HETTA HM01RF Wireless Programmable Thermostat USER MANUALS

HETTA HM01RF Wireless Programmable Thermostat

TIME AND PROGRAMME SETTING

1. Time setting
   Press enter time setting mode. Each press will switch between Hour, Minute & Day (Days being 1234567), use to adjust settings.
2. Time Period & Temperature Programming
   Setting the temperature to 00 ºC will make the time period INACTIVE.
   • Press and hold the button until the display shows “LooP” (cycle control); then, press to display either “12345” (Mon to Fri ), “123456 “ (Mon to Sat) or “123456 7 “ (Mon to Sun).
   • Press to enter the 1st time period ( icons are displayed for each period) and use to set the desired temperature, then press and set the required time. The settings are saved automatically.
3. Press to switch to the next time period, then to set the temperature and time.
4. Continue with  to access the remaining time periods.
5. The Auto icon displayed when the thermostat is in Auto mode.
   Pressing during a time period will switch over to temporary manual control where the temperature may be set to override the Auto setting. Auto mode is restored at the next time period.
   Pressing switches between Auto and Manual modes.
6. Modify the time period setting
   Press first, then press; to switch to the time period option to modify time settings.

DEFAULT TIME PERIODS

Period		Icon	Default Period Time	Default Period Temperature
Working Day	1		06:00	20℃
	2		08:00	15℃
	3		11:30	15℃
	4		12:30	15℃
	5		17:30	22℃
	6		22:00	15℃
Weekend	1		08:00	22℃
	2		23:00	15℃

WIRING DIAGRAM

Please refer to Wireless Wiring Centre User Manual (HWC018RF) for detailed wiring instructions. It is recommended that a qualified Electrician is consulted, or used for the installation of this product, in accordance with the current IEE Wiring and Building Regulations.

ADVANCED SETTINGS

In “power off” state, first press and hold , then press to enter advanced settings, which are saved automatically once the backlight is out. Press to set next data.

No.	Symbols	Setting Item	Parameter Setting Function	Factory Default
1	SEN	Sensor control option (NTC)	0: internal sensor 1: external sensor 2: internal control temperature, external limit temperature	0: internal sensor (“Err” is displayed if selected wrongly, or NTC is faulty. Heating stops until corrected)
2	OSU	Temperature limit of external sensor	5-99 oC	42 oC
3	dlF	Return difference of temperature limit value of the external sensor	1-9 oC	2 oC
4	SUH	Set the upper-temperature limit value	5-99 oC	35 oC
5	SUL	Set lower limit temperature value	5-99 oC	5 oC
6	AdJ	Synchronise display the temperature reading	-5 oC to +5 oC	0.5 oC
7	FrE	Anti-freezing function (only for water heating)	00: anti-freezing function closed 01: anti-freezing function open	00: anti-freezing function shut down
8	Loc	Keylock	00: Unlock 01: All keys locked except power key 02: All keys locked	00: Unlock
9	SNP	Alternate Parameter	00 01: Active	00
10	FAC	Factory default	08: Using current user settings 00: Restore factory default (set to 00 and press	00

Note: The temperature limit of the external sensor is factory set at 42 oC (OSV). The return difference of this temperature is factory set at 2 oC (diF). When the temperature reaches 44 oC , the thermostat will switch the heating output off. When the temperature drops down to 40 oC , the thermostat will switch the heating output back on.

PRODUCT SUMMARY

This new design heating thermostat is designed to be used with the Hetta Wireless Wiring Centre HWC018RF. With a large LCD display it can be positioned within the building, without extra cables.

TECHNICAL DATA

• Power supply: 1.5V*2
• Load current: 3A
• Consumption: <0.3W
• Temperature sensor: NTC
• Accuracy: ±0.5ºC
• Set-point temperature Range: 5ºC – 60ºC
• Limited temperature range: 5-99ºC

BUTTON DESCRIPTION

BUTTON DESCRIPTION
KEY	DESCRIPTION
	On / off
	Mode key: Press to switch between auto/manual time interval control. Allows temporary manual operation and time interval pre-set function
	Time setting: minutes/hours/weeks
	Raise temperature setting, programmed parameters					to increase
	Lower temperature setting, programmed parameters					to decrease
	Keylock Press for 5 sec to lock and unlock

Note: If the backlight is not on when the thermostat is in operation, this means the battery power is low, in which case please replace the batteries.

SCREEN DISPLAY

DISPLAY FUNCTIONS

• Manual control
• Temporary manual control
• Auto control
• Water is heating
• Anti-freezing function
• Morning, the first time interval
• Evening, the fifth time interval
• Leaving the house, second-time interval
• Afternoon, fourth-time interval
• Lunchtime, third-time interval
• Night/sleep, sixth-time interval

HM01RF WIRELESS PAIRING INSTRUCTIONS

• Locate the Bar Code within the Wireless Wiring Centre.
• To set SN code use the following steps:
• VAL: control valves 1-8, the factory default is 1.

1. Turn the Wireless Wiring Centre ON.
2. After inserting the batteries, turn the Thermostat OFF.
3. Press and hold the TIME button and then press the POWER button. The Advanced Settings page will now be displayed.
4. Press the MODE button until SNP 00 is displayed, change this to read 01 using the UP button. (00 = Inactive 01 = Active)
5. Press the MODE button and ensure FAC 08 is shown, then press the POWER OFF button.
6. Within 10 seconds, press and hold the DOWN button and then press the POWER button. SN1 and a Flashing Number will now be displayed.
7. Using the UP & DOWN buttons enter the first 2 digits of the 14-digit Barcode number, found in the Wireless Wiring Centre, then press MODE to display SN2, and enter the second 2 digits. Repeat this process to SN6.
8. After the sixth 2 digits are entered, press MODE again. CHh will now show the last 2 digits of the Barcode number.
9. Press MODE again to display VAL and enter the number of the Zone Valve to be controlled, eg, 02.
10. Press MODE again to go back to the home screen, and test by increasing the SET TEMP to 2 degrees above the ROOM TEMP. After approx. 3 seconds the selected Zone Valve Relay will operate.

Reference:

DOWNLOAD MANUALS:

HETTA HM01RF Wireless Programmable Thermostat USER MANUALS

HETTA HM01RF Wireless Programmable Thermostat USER MANUALS