Frico

Frico TPT16 Programmable Electronic Thermostat Operating Instructions

 

Frico TPT16 Programmable Electronic Thermostat

Setup

This manual describes the most essential functions and technical specifications of the thermostat. These instructions help the user to control the thermostat, and the electrician to install and set up the thermostat.

Technical specifications

  • Display: 1.8” TFT, 128×160 resolution
  • Power supply: 230V – 50/60 Hz
  • Maximum load: 16A (resistive)
  • Setpoint temperature range: +5 °C/+40 °C U
  • sage temperature range: 0 °C/+40 °C
  • Temperature setback: Pilot wire 230V – 50/60 Hz
  • IP class: IP21
  • Standard Color: White RAL9003
  • Sensors: Built-in room sensor and floor sensor
  • NTC 10kΩ included
  • Wi-Fi: 2.4GHz 802.11bgn (TPT16WF)
  • Approvals: EN 60730-1, EN 60730-2-9,
  • EN 300 328 V2.2.2

Installation

Installation must be done by a qualified electrician in accordance with wiring and building regulations. Before installation, disconnect any power to the thermostat’s mains. During the installation of the thermostat, power to the thermostat must be disconnected or isolated AT ALL TIMES!  Release the front cover by pressing a screwdriver from the ejector latch at the bottom of the thermostat. Open the spring and remove the frame.

Wires must be stripped 9-10 mm. Wires can be released by pressing the connector’s release pin. The floor sensor must be placed into the protective tube in concrete. Make sure there is no water in the tube. Now connect the wires to the thermostat’s terminals:

  • PILOT: Pilot Wire (if applicable)
  • LOAD (N): Heating Cable connection (Neutral)
  • N: Power connection (Live)
  • L: Power connection (Neutral)
  • LOAD (L): Floor temp sensor NTC type
  • SENSOR: Heating Cable connection (Live)
  • Pilot Wire (if applicable)

Next, position the thermostat and fasten it onto the wall’s mounting box using 2-4 screws. Open the frame retaining spring, position the frame, and close the spring. Then attach the front part, and make sure the connector between the front and the bottom part is correctly placed. Press the front part until it snaps in place. The front part can later be removed by pressing the ejector latch.

Start-up
After connecting the power to the thermostat for the first time, or after performing a factory reset, a start-up wizard will prompt the following questions:

  • Language  Set language
  • Set timezone Timezone compared to GMT
  • Daylight saving in use Y/N
  • Date / Time Set current date & time
  • Thermostats use Heating or cooling
  • Heating system Floor (Slow), Floor (Fast), Other (Fast)
  • Floor-type Concrete or wood
  • Floor Temp limit 6-40 (concrete) 6-27 (wood)
  • Regulate Room/floor or power reg.
  • Load size  Specify the load
  • Gradual heating  ON or OFF, used with new concrete floors to limit temperature rise time

Note: Wooden floor requires that a floor sensor is connected. Thus, floor temp is limited to 27 °C.

Symbols

Control
The thermostat is controlled directly or via App Frico TPT (TPT16WF), see “Wi-fi settings (TPT16WF)” and “Phone applications (TPT16WF)”
The thermostat has three touch-sensitive capacitive buttons. These are:

  • Left (Up)
  • Center (Confirm)
  • Right (Down)

Each button has its own background light. At any time, when any of the buttons’ background light is lit, the button is available for use.
TIP: Holding the left button for 2 seconds at any time, will make a quick return to the main screen.
TIP: While browsing the thermostat’s menu, pause at any menu item for a while, and a help text will be shown.

Standby and Main screen
When the thermostat remains untouched for a while, it will automatically go to the standby screen. While on standby, touching any of the buttons will display the main screen below:

  1. Time
  2. Operation mode
  3. Wi-Fi indicator (TPT16WF)
  4. Heating switched
  5. Setpoint
  6. Measured temp (Room or floor sensor)

On the main screen, pressing the center button will access the main menu. Pressing the left or right button will change the set temperature.

Menu items

  • Operation mode See “Operation Mode”
  • Schedule See “Schedule”
  • Settings Adjust settings
  • Wi-Fi Adjust Wi-Fi settings (TPT16WF)
  • Energy consumption Show energy consumption
  • Child Lock Activate key lock
  • Info  Thermostat information
  • Shut down  Switch thermostat on/off
  • Back Go back to the main screen

TIP: “Energy Consumption” shows consumption statistics over different time periods. Press the center button to change the unit or reset the statistics.
TIP: Select “Child Lock” and press the center button three times to activate/deactivate the key lock.

Operation mode

The thermostat has three main modes: Home, Away, and Schedule. The additional modes are Anti-frost and Power regulation.

Home
Pre-set temperature while you are home. The temperature setting can be changed by the user and it is saved.

Away
Pre-set (reduced) temperature while you are away. The temperature setting can be changed by the user and it is saved. The external pilot signal will also change operation mode between Home and Away.

Schedule
The thermostat follows the settings programmed in the Schedule menu. Programming can also be done with a phone application(TPT16WF).

Anti-frost
This mode drops the setpoint to 7 °C. It can be used e.g. in a summer cottage during winter time.

 

Power regulation
Fixed power mode, which operates without feedback from sensors. Relay conduction time is selected e.g. 20% which means the relay is ON 20% and 80% OFF during the cycle time. Cycle time is 30 minutes.

Open window function
If the room temperature drops rapidly, the mode will be changed to Anti-Frost mode. When the temperature raises, the thermostat will return to the earlier used mode. The Open window function will automatically deactivate after 30 minutes. The function is disabled as default.

Schedule
Create customized daily schedules to minimize energy consumption and maximize comfort. There can be up to five set points per day. A set point is given a target set time and a target set temperature for the thermostat to regulate automatically. You can view your daily heating schedule in this menu. Set points can be added and removed according to your preferences.
TIP: Create a daily schedule for a weekday according to your preferences. Then use the copy/paste function to duplicate the given day’s scheme to other weekdays.

Settings

  • Language Set language
  • Brightness Adjust display brightness
  • Color theme Dark/Light
  • Standby screen ON/OFF
  • Backlight delay 5-30s
  • Show help No/2-15s
  • Advanced settings Go to advanced settings
  • Back Go back to the main screen

Advanced settings
WARNING: Advanced Settings is recommended only for expert users. Consult your supplier or use it with extreme caution! Incorrect settings may damage your floor or heating system! The advanced settings menu contains the following items:

  • Heating Setup  Change the heating or cooling setup
  • NTC sensor Change NTC type
  • Hysteresis Change temp variation
  • Calibration Fine tune temp measuring
  • Temperature limits Set limits for room and floor temp
  • Pilot wire Change pilot wire settings
  • *Adaptivity See below.
  • Factory reset Perform a full factory reset
  • Restart the device Perform a reboot
  • Back Go back to the settings

ADAPTIVITY: The thermostat will automatically start/stop heating proactively to reach the set temperature at the set time. If adaptivity is switched off, the thermostat will start/stop heating at the set time instead of operating proactively to reach the set temperature at the set time.

Wi-Fi settings (TPT16WF)

When the thermostat is not connected to the cloud “Connect to the cloud” can be started from the Wi-Fi settings menu. Connection is done together with the phone application “Add thermostat”. The thermostat will show two three-digit PIN codes, which will be copied to the phone application. The password for the selected Wi-Fi network will be given in the phone application. When the Add Thermostat operation is finalized thermostat will reboot. After the thermostat is connected to the cloud the Wi-Fi settings menu will offer the possibility to turn Wi-Fi OFF/ON. Existing Wi-Fi settings will be used when turning Wi-Fi back ON. To change the Wi-Fi network or password please use Connect to Cloud menu together with the phone application’s Reconfigure Wi-Fi menu.

Phone applications (TPT16WF)
Download ”Frico TPT” from the App Store or Google Play.

Packaging
Packaging materials are chosen with consideration to the environment and are therefore recyclable.

Handling of product at end of working life
This product may contain substances necessary for the functionality of the product but are potentially dangerous to the environment. The product should not be disposed of mixed with general household waste but delivered to a designated collection point for environmental recycling. Please contact the local authority for further details of your nearest designated collection point.

Wiring diagrams

Main office
Frico AB Tel: +46 31 336 86 00
Industrivägen 41
SE-433 61 Sävedalen mailbox@frico.se
Sweden www.frico.net
For the latest updated information and information about your local contact: www.frico.net

Reference

Download Manual:

Frico TPT16 Programmable Electronic Thermostat Operating Instructions

Frico TPT16 Programmable Electronic Thermostat Operating Instructions

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago