FINDER

FINDER 1C.B1 SMART THERMOSTAT INSTRUCTION MANUAL

FINDER 1C.B1 SMART THERMOSTAT

A step-by-step guide to accessing all the functions of the Finder Bliss2 smart thermostat Type 1C.B1.9.005.0007

EASY INSTALLATION

TECHNICAL SPECIFICATION

  • Power supply: 3×1.5 V alkaline batteries type AAA – LR03
  • Temperature adjustment: (+5…+37)°C
  • Resolution: 0.1°C
  • Degree of protection: IP20
  • Output: 5 A 250 V AC changeover volt-free contact
  • Mounting: Wall

INSTALLATION NOTES

SAFETY REQUIREMENTS
The installation and assembly of electrical equipment must be performed by experienced personnel. Before connecting the thermostat, make sure that the load (pump, valve, boiler, etc.) is not powered and that it falls within the thermostat’s contact rating.

POSITIONING
Install the thermostat away from heat sources (radiators, direct sunlight, kitchens), away from doors/windows, and mount approximately 1.5 meters above floor level.

FIXING BASE TO WALL
First, detach thermostat from its base by inserting two fingers into the central rear hole and, with the other hand, pull the front of the thermostat towards you.

FIXING BASE
Secure the Smart Bliss2 thermostat base to the wall using the screws included in the package. When fixing, be careful not to over-tighten the screws to avoid damaging the base

ELECTRICAL CONNECTIONS
To make the connections, first refer to instructions for your heating system (pump, valve, boiler, etc.), then remove the terminal cover and connect the appropriate wires to terminals 6 (COM) and 7 (NO) of the Smart Bliss2 thermostat

Type 01C.02.8.230.0500: OPTIONAL power supply Using the external power supply, the batteries MUST be removed.

BATTERY INSERTION AND MOUNTING THE THERMOSTAT

  • Insert 3 x 1.5V alkaline batteries type AAA – LR03, paying attention to the indicated polarity. After inserting the batteries, initialization screens will appear. Wait for this process to finish and the detected temperature will then appear.
  • Mount the thermostat to its base by first engaging the bottom part of the thermostat with the lower pins of the base plate, then close the upper part of the thermostat to lock onto the upper pins

The thermostat is now ready to be configured. However, the Gateway2 (1Y.GU.005.1) must first be installed.

GATEWAY2 INSTALLATION
Connect the Micro USB connector to the Gateway2 (1Y.GU.005.1) and plug the power supply into to the elecrical outlet

After switching on, the luminous base of the Gateway2 flashes with a fading white light – which indicates it is awaiting configuration.

CONFIGURATION
To configure the Gateway2 and the Smart Bliss2 Thermostat, download the Finder Bliss application from the Google Play Store or the Apple Store and proceed with the configuration following the tutorial on the App. When requested by the App, activate the association of the thermostat following the following screens

When done, the temperature detected by the Smart Bliss2 thermostat will be displayed in the application

THE LUMINOUS BASE – NOTES

WHITE LED

  • Fading flashing: waiting for configuration
  • Fixed: Wi-Fi network and Cloud connection present
  • 2 Flashes: Connected to the Wi-Fi network but no connection to the Cloud (Check your Internet connection)
  • 3 Flashes: No connection to the Wi-Fi network and no connection to the Cloud (Check your Wi-Fi network)

BLUE LED
Flashing: sending Bluetooth commands

RED LED
Flashing: sending commands to the Smart Bliss2 Thermostat

To change the light intensity of the GATEWAY2 base, press the button 3 :

  1. 1 Once: Low brightness
  2. 2 times: Medium-Low brightness
  3. 3 times: Medium-High brightness
  4. 4 times: High brightness

RESET
Press the button for> 10 seconds to restore factory settings

OVERVIEW OF SCREENS & ICONS

ROOM TEMPERATURE
Thermostat is set to AUTOMATIC mode (AUTO) and will respond to programming via the App. Current room temperature is displayed.

TARGET TEMPERATURE IN MANUAL MODE
The thermostat is set to MANUAL mode. The target temperature is displayed.

MANUAL MODE
Thermostat is set to Manual mode. If the small arc segment at the top is coloured, the heating or cooling system is active. If red – heating If blue • cooling.

HOURS SETTING
This displays the number of hours for which the manual mode is to apply. From 1 hour (h01) to permanent (hæ).

FULL ARC
Appears when a setting is accepted and when the heating or cooling system is active.

HUMIDITY DETECTED IN THE ATMOSPHERE
In this section you can opt to view the level of humidity in the atmosphere (% RH).

0/0RH
Display of Relative Humidity currently present in the atmosphere.

ON/OFF SECTION
In this section you can turn the thermostat ON or OFF.

ON MODE
With ON mode selected, the thermostat can function in either AUTO or Manual modes.

OFF MODE
With the OFF mode selected, the thermostat will still maintain a frost protection setting of + 50C to avoid freeze damage to the system.

SETTINGS MENU
From here you can access the device settings.

ASSOCIATION WITH THE GATEWAY
The opposing arrows will flash only during the gateway pairing procedure.

TRANSMISSION TEST WITH THE GATEWAY
At this point in the menu you can perform a signal transmission test between the gateway and the thermostat.

RESULT OF THE TRANSMISSION TEST WITH THE GATEWAY

  • O SIGNAL ABSENT: the gateway is unreachable
  • 1/6 POOR: bring the two devices closer
  • 7/8 GOOD: make changes only if errors are found
  • 9/10 VERY GOOD: stable connection.

FIRMWARE VERSION
At this point in the menu it is possible to view the firmware version present on the device

MANUAL MODE

ON/OFF MODE

AUTOMATIC (AUTO) MODE

HUMIDITY

ASSOCIATION WITH THE GATEWAY

BEFORE FOLLOWING THE ASSOCIATION PROCEDURE, OPEN THE BLISS APP AND ADD A NEW DEVICE

TRANSMISSION TEST WITH THE GATEWAY

RESULT OF THE TRANSMISSION TEST WITH THE GATEWAY

  • 0 SIGNAL ABSENT: the gateway is unreachable
  • 1/6 POOR: bring the two devices closer
  • 7/8 GOOD: make changes only if errors are found
  • 9/10 VERY GOOD: stable connection

HEATING/COOLING

ACCORDING TO THE OPERATING MODE OF THE THERMOSTAT, YOU WILL SEE DIFFERING VISUAL FEEDBACKS ON THE LUMINOUS ARC

HEATING
THE ARC IS RED

COOLING
THE ARC IS BLUE

GATEWAY SET-UP

FIRST STEPS
Connect the gateway to the socket using the micro USB power supply before starting the procedure.

IMPORTANT
The BLISS2 smart thermostat is only compatible with the second generation gateway

Type 1Y.GU.005.1.
The code is shown under the black silicone cover at the top of the gateway. The gateway works only with 2.4GHz Wi-Fi networks. Check that you have a 2.4GHz network configured on your home router and that you have the network name and password before starting the procedure.

  1. After logging in to the new Bliss app, click on “Add device” to start the association
  2. Select “Bliss2” to star the association of the gateway and the thermostat
  3. Select an existing house (created with Yesly) or create a new one to define which system the gateway belongs to. Then press “Continue”.
  4. Select the time zone you are in. The default is for Italy
  5. Select “Configure a new gateway” and give it a name. Then press “Continue”.
  6. After selecting the gateway to associate, choose to connect it to the Wi-Fi network. Then press “Continue”.
  7. You can choose whether to associate the gateway to the network by selecting it from those available or by scanning the QR code located behind the router.
  8. After choosing the network to associate with, the gateway will complete the association
  9. Now you need to put the Bliss2 thermostat in “connection” mode. Go to the device and make the arrows blinkExecute this procedure on the Bliss2:
  10. The gateway is now communicating with the Bliss2. Please, wait.
  11. When the procedure is over, give the Bliss2 a name.
  12. Finder Bliss2 is properly paired. Now all you have to do is configure the temperature schedule and discover the rest of the functions of your new Smart Bliss2 Thermostat.

FINDER FRANCE Sari Avenue d’ltalie Zl du Pré de la Garde

  • F – 73300 ST. JEAN DE MAURIENNE
  • Tel.+33/479/83 27 27
  • Fax +33/479/59 80 04
  • finder.fr@finder.fr

S.R.L FINDER BELGIUM – B.V Bloemendael, 5 B- 1547 BEVER

FINDER P.L.C. Opal Way – Stone Business Park STONE, STAFFORDSHIRE ST15 OSS – UK

FINDER ASIA Ltd. Room 901 – 903, 9F, Premier Center20 Cheung Shun Street Cheung Sha Wan, Kowloon Hong Kong

findernet.com

Reference

Download Manual

FINDER 1C.B1 SMART THERMOSTAT INSTRUCTION MANUAL

FINDER 1C.B1 SMART THERMOSTAT INSTRUCTION MANUAL

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago