SAFETY REQUIREMENTS
The installation and assembly of electrical equipment must be performed by expert personnel. Before connecting the chronothermostat make sure that the load (pumps, valves, boiler, etc …) are not powered-up and are within the rating of the contact To remove the base use the appropriate slots 1 and 2
POSITIONING
Install the chronothermostat away from heat sources (radiators, direct sunlight, kitchens) and doors/windows. Mount about 1.5 meters above floor level.
FIXING
Use screws 0 3.5 mm MAX – maximum head thickness 3 mm. When fastening, do not over tighten the screws to avoid distorting the base.
CLEANING
Use only a damp cloth for cleaning.
Fix the base on the wall and make the electrical connection as shown on the diagram
NOTE
Even if it is supplied by a power supply, the Bliss Wi-Fi display will NOT stay always on.
Insert the batteries into the battery compartment, respecting the indicated polarities.
CAUTION Incorrect battery polarity can cause the batteries to leak acid and damage the chronothermostat, invalidating the guarantee.
Fix the chronothermostat on its base as shown in the figure below
NOTE To disassemble it, proceed in reverse
NOTE
If only one of the two pairs is reversed, the device works the same, only the battery life is halved.
The Chronothermostat is provided with 2 battery thresholds: the first threshold indicates that the batteries are low and must be replaced. In this condition, and with the display in the off state, a flashing battery icon will be seen every 5 seconds
After touching the Finder button and turning on the display, the battery icon will continue to flash
At the second threshold the Chronothermostat turns off, this condition the flashing battery icon can be seen every 5 seconds (until the batteries completely run out).
If the chronothermostat is not connected to the Wi-Fi, after replacing the batteries reset the date and time.
POWER ON THE DISPLAY
CHRONOTHERMOSTAT OFF
NOTE After setting the year, the chronothermostat automatically recognizes the day of the week and automatically a number from 1 to 7 will appear on the display to indicate the day of the week
MINUTES
NOTE
At each programming step it is possible to go back one step using the back button
To exit the manual setting and return to the main screen, press the “hand” button.
WEEKLY PROGRAMMING
Press the numbers corresponding to the days of the week to be programmed (1 = Monday … 7 = Sunday). At the end of the selection, press the Finder key.
The screen indicates that the temperature will be programmed (right) at the time indicated on the left. Set the desired temperature with the cursor at the indicated time (in this case between midnight and one in the morning). Press Finder to confirm the schedule and move to the next hour
Set the desired temperature with the cursor at the indicated time (in this case between one and two in the morning). Press Finder to confirm the schedule and move to the next hour
Proceed in the same way until reaching the 23:00 Hour time period.
NOTE
To go back to the previous step, use the back button or the Finder button to switch to the next time programming. To exit programming and save the values set so far, press the Finder button for 2 seconds.
COPY PROGRAM
To copy the program of one day to use for another day (s), simply press the day to be copied first and then the day (or days) on which to obtain the same programming. Then press the Finder button for 2 seconds to confirm and return to the main menu.
Example: reviewing day 3 (Wednesday)
Repeatedly press the Finder button to step through and display the hours together with the appropriate set temperature. To go back to the previous step use the back button. Press the Finder button for 2 seconds to save and exit the review.
STATE & FROST PROTECTION FUNCTION
When the chronothermostat is off, the display will show the word OFF. But in this condition, the frost protection function remains active. If the room temperature falls below the frost protection temperature, the flame icon will appear together with the word OFF.
The chronothermostat can only be locked using the Finder Bliss application. When the lock mode is activated, the Chronothermostat will display a lock icon.
To unlock the chronothermostat you will need to enter the PIN as shown below
Caution
By entering an incorrect PIN code, the Chronothermostat will display Err for an instant and then propose a re-try. After entering the wrong PIN 3 times, the chronothermostat will remain locked for 20 seconds with the word Err displayed (the display will turn off after 5 seconds to reduce battery drain). This procedure repeats for any further attempt to enter the wrong PIN.
NOTE
Removing the batteries will not cancel the lock. If you forget your PIN, use code 618 to unlock the product.
Download the Finder Bliss application to your smartphone. The pairing procedure will be described in the application. Turn on Wi-Fi and search for a network
In the case where the APP credentials were not inserted by the expiry of the timeout, the Chronothermostat performs a RESET of the configuration and the internal Wi-Fi is turned off.
CHRONOTHERMOSTAT Wi-Fi CONNECTION TO THE NETWORK
After connecting the timer-thermostat to the home network, the update will take place within 4 to 40 minutes, depending on the update time set on the application. To immediately connect the chronothermostat to the App, with display off, press the Finder button for 3 seconds. Segments will appear to indicate waiting for parameters to be synchronized with the APP.
If the wait for synchronization persists for too long it means that the chronothermostat has difficulty updating with the cloud (via the APP). The problem may be due either to the poor network signal (seen by the Chronothermostat) or to a slow home connection, busy broadband or slow server response. Battery life depends greatly on connection times. After 20 seconds, if the connection has not occurred, an error message appears (see page 18). If there was a previous connection to the Cloud the chronothermostat will display the last setting received from the server.
GENERAL CHARACTERISTICS
Type | Wi-Fi wall-mounted weekly programmable thermostat |
Wi-Fi frequency | 2.4 GHz |
Encryption | WPA2 / PSK |
Display | LED |
Resolution | 1 hour (1 minute via APP*) |
Daylight Saving Time | Automatic Update |
Battery life | About 1 year (Over 1 year depending on the mode set by APP) |
Functions | Additional settings available on the APP |
The time slot can not start and end at the same time
DEFAULT PARAMETERS | |
Season set | Winter |
Frost protection | Fixed at 5°C |
Thermal differential | 0.2°C |
INDICATION OF ERRORS (ACCORDING TO VERSION)
ANTENNA SIGNAL
On the APP it is advisable to check for a BLISS signal of at least 3 notches to ensure a good operation.
IB1C91 – 12/22 – Finder S.p.A. con unico socio – 10040 ALMESE (TO) – ITALY
Download Manual:
FINDER 1C.91 PROGRAMMABLE THERMOSTAT Instruction Manuals
Other Manual:
FINDER 1C.91 PROGRAMMABLE THERMOSTAT Product Specification Guide
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…