Apple HomeKit technology provides an easy, secure way to control HomeKit-enabled accessories using Siri on your iPhone, iPad, or iPod touch. After installing your FIBARO Heat Controller configure it from a compatible app with just a few simple steps. You can even create your own custom scenes to control your home settings. For example, you can create a scene to automatically turn off the lights, lock your doors, close the garage door, and set the thermostat to the desired temperature in just one step
Important safety information
Read this manual before attempting to install the device! Failure to observe the recommendations included in this manual may be dangerous or cause a violation of the law. The manufacturer, Fibar Group S.A. will not be held responsible for any loss or damage resulting from not following the instructions of the operating manual. ! This product is not a toy. Keep away from children and animals CR2032 coin cell battery is harmful if swallowed
Battery pack warning!
The Heat Controller contains a lithium-ion polymer battery pack, heed all the following warnings:
FIBARO Heat Controller is a HomeKit-enabled, remotely controlled thermostatic head to control temperature in your room using Bluetooth® low energy wireless technology. It measures the temperature and automatically adjusts the heat level. It can be mounted without tools on three types of thermostatic radiator valves. You can create schedule via app to easily manage temperature throughout the week.
Main features of FIBARO Heat Controller:
3 types of controlling the temperature in FIBARO Heat Controller:
Pairing with HomeKit
You can set temperature using app (10-30°C) or directly on the device (16-24°C). During manual temperature change LED ring colour corresponds to the temperature set-point.
To check and change the temperature on the device:
The device can be used with an additional, dedicated temperature sensor (FGBRS-001) to provide the best temperature regulation. It can be placed anywhere in the room and the device will use it as a reference point for the room temperature. Before using, the sensor must be paired with the thermostatic head. One thermostatic head can be paired with only one sensor, but one sensor can be paired with up to three thermostatic heads
To pair the FGBRS-001 with the device:
Extra temperature sensor
NOTE FGBRS-001 is the only compatible external temperature sensor.
To remove all paired heads:
Before dismounting, the device must be put in Standby Mode to ensure safe removal. See chapter “Standby Mode” on page 12 for more information
To dismount the device:
Menu
Menu allows to perform important configuration and maintenance actions. In order to use the menu:
After enabling the local control protection changing temperature directly on the device (by turning it) will not be possible. Enabling local protection is recommended if you want to prevent accidental temperature change, e.g. by children. Local protection can be enabled/disabled manualy or via app. When attempting to change temperature if local protection is enabled:
To enable/disable local protection:
Calibrating the device to your radiator valve is required for proper controlling the temperature.
Calibration is performed:
To perform calibration using the menu:
Standby Mode
In Standby Mode the device is in deep sleep state allowing for safe dismounting, transporting and low as possible battery consumption. The device is shipped in Standby Mode. Entering the device in Standby Mode will not factory reset the device nor will result in loosing any data, but calibration and sensor pairing (after long Standby) is lost
To enter Standby Mode:
To exit Standby Mode click the button once, the device will enter first installation procedure
Reset procedure allows to restore the accessory back to its factory settings, including HomeKit and extra temperature sensor pairing and device configuration.
To perform factory reset:
The device is equipped with a rechargeable lithium-polymer battery pack that can be charged via micro-USB port using standard 5V charger (not included). When battery is low the LED ring will start to blink red. The device will also report low battery status of itself and dedicated temperature sensor (if paired) to the controller. The device does not operate the valve and maintains the last valve position until fully charged
To charge the battery:
The device allows to create heating schedule to manage temperature in the room throughout the week. Schedule is created via app. Up to 50 different rules can be created in schedule
To create rule user should specify:
Override Mode is a special type of mode that overrides schedule. Override Mode starts right after setting it for fixed duration (4 hours by default). Duration can be changed in FIBARO app.
To start Override Mode set temperature by turning the knob or change the temperature via app, while schedule is active. LED ring will pulse quickly with selected colour.
To exit Override Mode grab knob with your hand for 5 seconds
There are 3 special types of override modes:
External sensor status (read-only)
Status of the connection with external temperature sensor
Available settings: | 0 – unpaired 1 – paired |
Default setting: | 0 (unpaired) |
Lock physical control
Parental lock of manual control. When enabled the device prevents changing the temperature by turning the knob until it is disabled by this parameter or from the menu.
Available settings: | 0 – manual control enabled 1 – manual control disabled |
Default setting: | 0 (enabled) |
Calibration
Forcing automatic calibration of the device
Available settings: | 0 – device is not during calibration 1 – force autocalibration |
Default setting: | 0 |
Status faults
The device reports the status of detected errors in the form of a bit mask (status faults). Values can be combined, for example: code with value 5 (1+4) means low battery and calibration error were detected
Code | Status |
0x01 | Low battery of external sensor – battery level of extra temperature sensor is low. Change the battery. |
0x02 | Hardware fault – fault of the device. Device will try to calibrate again. |
0x04 | Calibration error* – unsuccessful calibration. Device is unable to work properly. |
For communication with the controller:
For communication with the extra sensor (FGBRS-001):
Sensor specification (FGBRS-001)
Legal Notices
All information, including, but not limited to, information regarding the features, functionality, and/or other product specification are subject to change without notice. Fibaro reserves all rights to revise or update its products, software, or documentation without any obligation to notify any individual or entity. FIBARO and Fibar Group logo are trademarks of Fibar Group S.A. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Fibar Group S.A. is under license. Apple, iPhone, iPad, iPad Air, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc. All other brands and product names referred to herein are trademarks of their respective holders. Use of the Works with Apple HomeKit logo means that an electronic accessory has been designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Warning
This product is not a toy. Keep away from children and animals! CR2032 coin cells are harmful if swallowed!
Declaration of conformity
Hereby, Fibar Group S.A. declares that the device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.manuals.fibaro.com
WEEE Directive Compliance
Device labelled with this symbol should not be disposed with other household wastes. It shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.
DOWNLOAD MANUALS:
Fibaro FGBHT-001 RADIATOR THERMOSTAT User Manual
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…