Fantini cosmi CH140GSM2 WEEKLY PROGRAMMABLE THERMOSTAT QUICK GUIDE

Fantini cosmi CH140GSM2 WEEKLY PROGRAMMABLE THERMOSTAT

INTRODUCTION TO THE SYSTEM

CH140GSM2 is a weekly programmable thermostat with built-in GSM, which is also controlled remotely via SMS or via the “Intelliclima+” APP. Equipped with a temperature sensor, with two output relays on board, it simultaneously manages heating and air conditioning units. However, relay 2 can be dedicated to an external unit with an ON/OFF function based on daily programming

PRELIMINARY INFORMATION
The complete English manual is available at the following link: pdf.fantinicosmi.it

INSTALLATION

Installation must be done by qualified personnel in compliance with the requirements concerning installation of electrical equipment. Installation operations must be done with the system’s power disconnected. The programmable thermostat CH140GSM2 must be installed on the wall or on a flush mounting box, in 3 units or round, at a height of about 1.5m from the floor, in a position to properly detect room temperature.

Dimension

Installation Instruction

GSM FEATURES FEEDBACK

• The connection to the GSM network of the programmable thermostat can be detected by the antenna symbol and three bars.
• The antenna symbol flashes if the module is not registered on the GSM network (e.g. no coverage, SIM not inserted or blocked by PIN, etc.).
• Once registered, the antenna turns on steady and the bars appear accordingly, indicating the intensity of the signal.
• The following table shows the signal values and the corresponding signals shown on the display.

ELECTRICAL CONNECTION

DESCRIPTION OF DISPLAY KEYS

Pressing any key for the first time lights up the display.

1. GSM antenna
2. Day of the week
3. Activation status: air conditioning or heating
4. Room temperature (Celsius/ Fahrenheit)
5. Multi-function key icon
6. Multi-function key
7. Operating mode
8. Bar graph to display messages and daily programming

The function of the multi-function keys varies depending on the situation and is described by the symbol that appears on the display next to the key

LANGUAGE SELECTION

DATE AND TIME SETTING

TECHNICAL FEATURES

Temperature adjustment scale	2 ÷ 40 °C, increase 0.1°C
Measurement scale/ room T display	– 50 ÷ + 50 °C
Power supply	230V 50 Hz
Maximum absorbed power	10W
Output type	2 relays with dry changeover contact (COM/NA/NC) 3 screw clamps (closed + open)
Input type	■ 1 auxiliary probe – NTC 10K – Lmax 100m – cross-section 0.5 ÷ 1.5 mm2 ■ 2 auxiliary inputs – dry contacts
Buffer battery	For programming data and clock/calendar
Contact range	5(3)A 250 Vac
Type of action	1 B.U. (connection micro-switch)
Software	class A
Minimum adjustment differential	0.3 ÷ 5 K
The thermal gradient of reference	4 K/h
Maximum room temperature	45°C
Storage temperature	-10°C ÷ +60°C
Electric insulation	Double insulation

WASTE DISPOSAL
The symbol of the crossed out wheeled bin indicates that the products must be collected and disposed of separately from household waste. The batteries and integrated accumulators may be disposed of together with the product. They will be separated at the recycling facilities. A black bar indicates that the product was placed on the market after 13 August 2005. Participating in the separate collection of products and batteries contributes to the correct disposal of these materials and therefore avoids possible negative consequences for the environment and human health. For more detailed information on the collection and recycling programs available in your country, contact the local authorities or the sales point where you purchased the product

FANTINI COSMI  

• Via dell’Osio, 6 20090 Caleppio di Settala, Milano – ITALY
• Tel. +39 02 956821
• Fax +39 02 95307006
• info@fantinicosmi.it
• www.fantinicosmi.it

REFERENCE:

DOWNLOAD MANUALS:

Fantini cosmi CH140GSM2 WEEKLY PROGRAMMABLE THERMOSTAT QUICK GUIDE

OTHER MANUALS:

Fantini cosmi CH140GSM2 WEEKLY PROGRAMMABLE THERMOSTAT Technical Data Sheet

Fantini cosmi CH140GSM2 WEEKLY PROGRAMMABLE THERMOSTAT QUICK GUIDE