Do you already know about PROGmatic programming sticks? You can program SPARmatic comet by hand or you can use, for example, the comfortable PROGmatic-Bluetooth programming stick to copy your personally specified heating and economy times onto all your EUROtronic energy-saving radiator thermostats at your home which have a programming port in a matter of seconds. Detailed information and the *PROGmatic Programming sticks can be found on: www.eurotronic.org.
Please read the user manual before you place the thermostat. Keep the documents for later questions and provide them if you pass the thermostat on to other persons.
Application as directed
By purchasing the SPARmatic comet energy-saving radiator thermostat you own a programmable radiator thermostat that can be used for temperature regulations in enclosed rooms and therefore, it can contribute to the reduction of heating energy. – Please use the thermostat only for this purpose. The EUROtronic programming port is intended ONLY for ourEUROtronic programming stick. Never connect other devices with the programming port!
By pressing MENU you will arrive at the set-up menu. Please choose one of the items with the selector wheel. With OK you can select one menu item and with the selection wheel they can be adjusted. The button OK confirms the setting.
The button MENU leads to the previous level.
to select the mode
AUTO = automatic mode
MANU = manual mode
the setting of time programme
setting of comfort and economy temperature
setting of date and time
window function
reset of the device to the factory preset
starting of a new adaptation to adjust the valve
travel function
installation function (Please only attach the
controller to the coupling ring in this position)
adaptation of temperature to the room situation
standby function
version
Daylight saving time
Remove the battery lid by pressing the battery lid upwards (1) at the highlighted point and then taking it out (2).
Then insert the batteries as represented in the appliance. Do not use accumulators! Ensure that the polarity is correct! Attention: Never recharge batteries, danger of explosion! Do not short-circuit batteries! Do not disassemble batteries! Take low batteries out of the device immediately. Keep batteries away from extreme warming – danger of leakage! Do not apply used and new batteries together. If needed, clean the battery and the contacts before using them. Keep the batteries away from children. When getting in touch with battery acid instantly irrigate the affected parts with clear water and call a doctor.
After inserting the batteries for the first time the date will flash on the display. Now, the date and time can be set.
The display will be shown. Now, the motor will completely move to the installation position in order to make the installation easier. As soon as SPARmatic Comet is ready for installation will be shown on the display. ( – any time selected in the menu). Now please do not press any other buttons! Plug device for a coupling ring. ➔ mounting.
You can also set a date and time via the menu item later on. But in case of that, SPARmatic Comet does not move to the installation position.
➔ In case of replacing batteries, the stored time program will remain active. You should check the specified time to ensure that.
SPARmatic comet can be quickly and easily mounted on all common valves (see adapter table). It can be installed without the grime and water spots because the heating circuit is not interrupted.
ATTENTION: It must be possible to insert SPARmatic comet without applying force, ensure that the appliance is in the „ “ or „ “ position.
➔ In case of a later installation, please switch the menu to „ “ before you install the device. Herewith the installation is facilitated. Only mount it in this position.
Dismounting
➔ To remove the SPARmatic comet remove this at the (with the wheel turned on the highest temperature of over 28 C° to position), wait for a short period and then press on the unlocking device to detach the quick-release catch. Then pull the SPARmatic comet from the valve.
Initial installation: Press the button OK until appears on the display so that SPARmatic Comet will be able to start its adaptation. The device will adapt itself to the stroke of your valve body. To do this the valve will now be opened and closed several times to store the endpoints. In some cases, this process can take a few minutes. After successful adaptation, it returns to normal mode.
MANU-Modus
In the MANU-mode SPARmatic comet adjusts to the manually specified temperature.
AUTO-Modus
In the AUTO-mode SPARmatic comet changes between to temperatures according to the time program that has been set:
The heating and economy times can be specified via the adjustable time program. It is possible to set 8 switch points (4 heating and 4 economy times) per day at the most. SPARmatic comet has the following factory preset:
Heating time:
Heating with comfort temperature (factory preset: 1st heating time at 07:00)
Economy time: lowering to economy temperature (factory preset: 1st economy time at 22:00)
Setting heating and economy times
With SPARmatic comet, it is possible to set 4 heating and 4 economy times per day – one for each day or one for a block of several days. TAG1 to TAG7 represent the weekdays from Monday to Sunday. Additionally, the corresponding days are shown as abbreviations below the menu bar on the display.
Block construction:
Setting of an individual program:
Press MENU. Select the menu item with the selector wheel. Press OK . for Monday is shown on the display. Select day/block with the selector wheel. Confirm with OK. Set the beginning of the 1st heating time (symbol
Setting comfort and economy temperature Press MENU. Select the menu item with the selector wheel. Confirm with OK. Set the comfort temperature with the selector wheel. Confirm with OK. Set the economy temperature with the selector wheel. Confirm with OK.
➔ By the way: Maximum energy saving can be obtained with an economy temperature which is about 5 °C below the comfort temperature.
Manual operation
With the selector wheel an adaptation of the room temperature is possible at any time. In the AUTOmode it remains active until the next switch point is reached. Now, the usual program becomes active again.
Cleaning
To clean the SPARmatic comet use only a dry or lightly wet cloth. Avoid chemical solvents – they can probably damage the device.
Used devices
Do not throw old devices and packaging into the household waste. They can be recycled. You receive further information at your local government.
Adapter
Please remove all the connection pieces of the plastic adapters before you use one of the attached adapters!
Please completely remove the connection rods highlighted in grey prior to the assembly the adapter. You can find additional brass adapter models that are subject to a charge: at:www.eurotronic.org
Declaration of Conformity
The Declaration of Conformity is provided at: www.eurotronic.org
The three-year warranty begins on the day of purchase. Please keep the receipt as evidence of purchase in the future. During the guarantee period, defective radiator thermostats may be sent to the service address below. Please ensure sufficient postage is paid. A new or repaired device will then be sent to you free of charge. Following the expiry of the guarantee, you may still send the defective device to the address below for repairs. Please ensure sufficient postage is paid. Repairs carried out after the guarantee period are subject to a charge. Your legal rights are not affected by this guarantee. There is no new warranty period starting when repairing or replacing the device.
Please note that we only grant a warranty on the function of the device. We will not grant a warranty for the interaction between the thermostat and the bottom part of the valve. The technical data is only valid for the use of the following valves: Heimeier, Junkers Landys + Gyr, MNG, Honeywell, Braukmann (a measure of thread M30 x 1,5), Oventrop (M30 x 1,5) Danfoss RA, RAV, and RAVL. Please see the combinations of the devices on our website (www.eurotronic.org/ Adapter list) EUROtronic does not issue a guarantee when using the thermostat with valves that are not mentioned above.
Eurotronic Technology GmbH Südweg 1 36396 Steinau-Ulmbach
Telefon: 0 66 67 / 9 18 47-0
Servicehotline: 0 66 67 / 9 18 47-17
Email: info@eurotronic.org
Internet: www.eurotronic.org
* subject to a charge pack.-no. 900 000 250 1 | stand: 2014/05
www.eurotronic.org
Download Manual:
EUROtronic Comet programmable radiator thermostat User Manual
EUROtronic Comet programmable radiator thermostat User Manual
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…