Engocontrols

Engocontrols E901RXWIFI Wireless Thermostat QUICK GUIDE

Engocontrols E901RXWIFI Wireless Thermostat

INTRODUCTION

E901WIFI is a wireless, Wi-Fi room thermostat which enables economical and ecological control of any type of heating. The operation of the thermostat is very simple and allows the user to adjust the heating cycle to user’s rythm of the day. Built-in WiFi module (in the receiver) enables remote control of the heating system via a smartphone or a tablet using the ENGO application Smart / TUYA Smart. The devices are pre-paired and ready for work.

Product Compliance
This product complies with the following EU Directives: 2014/53/EU, 2016/65/EU 868.0 MHz – 868.6 MHz; <13dBm WIFI 2,4 GHz

Please note!
This document is a brief manual of the installation and operation of the product and highlights its most important features and functions.

SAFETY INFORMATION

Use in accordance with national and EU regulations. Use the device only as intended, keeping it in a dry condition. The product is for indoor use only. Please read the entire manual, before installation or use.

INSTALLATION

Installation must be performed by a qualified person with appropriate electrical qualifications, in accordance with the standards and regulations in force in a given country and in the EU. The manufacturer is not responsible for non-compliance with the instructions.
WARNING:
For the entire installation, there may be additional protection requirements, which the installer is responsible for

Care for the natural environment is of paramount importance to us. The awareness that we manufacture electronic devices obliges us to dispose of used electronic components and devices safely. Therefore the company has received a registration number issued by the Chief Inspector for Environmental Protection. The crossed out symbol the trash can on the product means that the product must not be disposed of with ordinary waste containers. Sorting waste for recycling helps to protect the environment. It is the user’s responsibility to surrender used equipment to a designated collection point for recycling waste from electrical and electronic equipment.

Wall mounting

Remove the thermostat cover as shown in the picture.
If there are batteries inside, remove them

Use a screwdriver to push the plastic tabs in as shown in the figure until you eel resistance, and tilt the front part of the housing.

Separate the front part from the back part in the direction shown above

Use the supplied mounting screws and mount the back cover to the wall (use holes as shown arrows)

Using the hinges on the left, fold the front and back covers together as shown in the picture above until they click into place.

Wiring Diagrams

E901RXWIFI receiver

Receiver’s switches description:

1. LEFT SWITCH
ON – Manual mode- receiver ON
2. OFF – Manual mode- receiver OFF
RIGHT SWITCH
3. MANUAL – Receiver works in manual mode according to the left switch)
4. AUTO – Receiver works in AUTO mode (according to the thermostat’s command)

LED indications in the receiver

The status of the receiver is indicated by two LEDs. These are LEDs with the following colors:

  • red (upper one),
  • green (upper one),
  • blue (upper one), 1
  • orange (lower one). 2

A detailed explanation of the meaning of the LEDs can be found in the table below:

DESCRIPTION
The red
LED flashes
TThe red LED diode flashes – Receiver and thermostat are prepared for installation in the app.
LED always flashes red:
– immediately after connecting the receiver to the power supply, if the thermostat is not added to the app – after running the parameter “APP “-> YES (installer parameters)
– after removing thermostat from the app (device automatically entered pairing mode)
The red
LED steady
The red LED diode is steady – E901 WIFI has not been installed in the app and it is working in Offline mode. It means also app pairing mode timed out (pairing with app must be done within 10 minute after enabling pairing mode).
The green LED is solid The receiver is connected to a router but there is no connection to Internet (router is offline)
The iireen LED flashes The receiver lost connection with a router (router is off)
The
LED is solid
The receiver is connected to a router that has Internet access (router is online)
The
LED flashes
The receiver was paired but lost communication with the thermostat due to out of range or low battery in the thermostat. When receiver lost communication with thermostat it starts flashing after 15 minutes.
The orange
LED is solid
In automatic mode, the receiver received a heating / cooling signal from the thermostat or
the receiver was started in manual mode (left switch ON, right switch MANUAL)
Theta UI.J44  –
LED flashes
The receiver is in the pairing mode and is looking for a signal from the thermostat (then you must
activate the “SYNC parameter in the thermostat). The receiver was paired but lost communication with the thermostat due to out of range or low battery in the thermostat. Orange diode starts flashing 15 minutes after lost communication from the thermostat.
The range
LED is off
The receiver does not send a heating /cooling signal.
The pink
LED is on
Update process started. To increase the chance of success of the update – immediately after the pink diode appears, dick any thermostats button to turn on backlight

LCD icon description

1. AM/PM 9. Low battery indicator
2. Clock 10. Antifrost Mode
3. Day of the week indicator 11. Cooling mode
4. Settings icon 12. Heating mode
5. Key lock function 13. Temperature unit
6. Send a signal (pairing) 14. Room / setpoint temperature
7. Internet connection 15. Manual mode/ Temporary override mode
8. Holiday Mode 16. Program number

Button description

Button Function
Change the parameter value down
Change the parameter value up
D Set the day of the week
H Set the hour
M Set the minutes
Manual mode
OFF mode / Holiday mode
AUTO mode / Back button
Programming / Program selection
Confirm function
Thermostat reboot, time reset

Setting Time / Setting Date
In the online mode – the thermostat reads the current time from the application.
In the offline mode – D/H/M buttons are active and day/time can be set manually

D– Press D button to set the day
H– Press H button to set the hour.
M– Press M button to set the minutes.

Manual mode – temperature settings
In manual mode, the thermostat maintains a constant setpoint temperature as long as the user will not change it again or will not switch to another operating mode (e.g.  schedule mode).

Setting setpoint temperature in manual mode

Press any button to highlight the screen, then follow the steps below:

Press, button to enter manual mode.
The hand icon should be visible on the display.

Using or button set new comfort temperature value. 

Confirm by button or wait until the thermostat will approve your choice itself and display the main screen.

OFF mode

  • Press any button to highlight the screen, then follow the steps below:
  • Press, button to enter OFF mode.
  • LCD is turned OFF, Thermostat is not sending signal for heating/cooling to the receiver.

To exit the OFF mode press again the button.
The thermostat will return to the previous mode.

Installation of the E901WIFI thermostat in the app

Make sure your router is within range of your smartphone. Make sure you are connected to the Internet. This will reduce the pairing time of the device.
Use only Wi-Fi 2,4GHz network

STEP 1 – DOWNLOAD ENGO SMART APP
Download the ENGO Smart app from Google Play or Apple App Store and install it on your smartphone.

https://play.google.com/store/apps/details?id=com.engo.smartlife 
https://apps.apple.com/us/app/engo-smart/id1606693444

STEP 2 – REGISTER THE NEW ACCOUNT
To register a new account, please follow the steps below:

  1. Click „Register” to create new account
  2. Enter your e-mail address to which the verification code will be sent.
  3. Enter the verification code received in the email.
    Remember that you only have 60 seconds to enter the code!
  4. Then set the login password.

STEP 3 – CONNECT THE THERMOSTAT TO WI-FI

  1. After installing the app and creating an account:
  2. Turn on Wi-Fi and Bluetooth on your smartphone. Connect mobile phone to the Wi-Fi network to which you want to assign the thermostat.
  3. Connect the receiver to the power supply.
    When first powered up, the red led will start flashing, which means that devices are ready to be added to the application.
    Go to step 7 (adding devices in the app).
    If the red LED on the receiver is not flashing, proceed with the next steps.
  4. Press and hold button for 5 seconds.
  5. Use or, button to choose APP – add to application parameter.
  6. Confirm with button.
  7. In the app, select: „Add Device”.
  8. Then choose: „Auto Scan”.
  9. After finding the thermostat, go „Next”.
  10. Select the Wi-Fi network which thermostat should connect and put it’s password.
  11. Wait for the app to configure thermostat.
  12. Name the device and click „Done”.
  13. Thermostat has been installed and displays the main interface.
  14. …and it shows on the main app window.
  15. When the blue LED on the receiver will light up, it means the device has been correctly added to the application and is now connected to the Internet.

When the blue LED on the receiver will light up, it means the device has been correctly added to the application and is now connected to the Internet.

E901WIFI pairing process with the receiver
PLEASE NOTE!
E901WIFI THERMOSTAT IS ALREADY PAIRED WITH THE RECEIVER!

If you want to re-pair the receiver and thermostat with each other and then add it to the application, make sure that the receiver is disconnected from the power supply, and  the switches on it are in the ON and AUTO positions. Then connect the receiver to the power supply and wait a few seconds. Next, move the left switch to the OFF position  and back to the ON position with a quick motion. The orange LED will start blinking, which will confirm that the receiver has entered the pairing mode.

Press and hold the button for 5 seconds.

Use or, button to select SYNC parameter.

Confirm with button.

Using or buttons choose YES and start the pairing process on a new frequency by pressing the button.

The thermostat started to send a signal to find the receiver (the symbol of the blinking antenna) and started the countdown with the number 10 (min). The pairing process may take up to 10 minutes.

When the orange LED stops blinking, the devices have been paired on a new frequency.

The thermostat will display the message „good”, which means that the devices are successfully paired with each other. Thermostat will return to the next APP parameter in  the service menu (adding to application).
You can skip this step and return to the main menu by clicking (OK) button a few times
WARNING! If the orange LED on the receiver has not stopped blinking after 10 minutes, repeat the pairing process taking into account the distance between devices,  obstacles and interference.

Installer settings

To enter installer parameters press and hold button for 5 seconds.

Useor. button to move between parameters. Enter the parameter by. Edit the parameter using or. Confirm the new parameter value  with the button.

Installer parameters

Pxx Function Value Description Default value
P01 Heating/Cooling
Selection
Cooling
Heating
P02 Control
algorithm
1 SPAN ±0,25°C 1
2 SPAN ±0,5°C
3 TPI for Underfloor Heating
4 TPI for Radiators
5 TPI for Electrical Heating
P03 Offset
temperature
-3.5 °
to + 3.5°C C
If the thermostat indicates
wrong temperature, you
can correct it by ± 3.5°C
0°C
PO4 Relay type NO Normally Open type of relay NO
NC Normally Closed type of relay
P05 Clock format 24h 24 hour 24h
12h 12 hour
P06 Minimum
setpoint
5°C – 20°C Minimum heating / cooling
temperature that can be set
5°C
P07 Maximum
setpoint
20°C – 35°C Maximum heating / cooling
temperature that can be set
35°C
P08 Key sound NO Key sound Off YES
YES Key sound On
P09 PIN Code NO Disabled NO
PIN Enabled
P10 Require a PIN to
unlock the keys
every time
NO Function disabled YES
YES Function enabled
SYNC Pairing with
receiver function
NO Function disabled NO
YES Function enabled
APP Pairing with
application
function
NO Function disabled NO
YES Function enabled
CLR Clear settings
factory reset
NO No action NO
YES Factory Reset

Technical specification

Thermostat supply 2 x AA batteries
Receiver supply 230 V AC 50 Hz
Receiver rating max 16 (5) A
Receiver outputs Voltage-free NO/COM relay
Temperature range 5 – 35°C
Control algorithm TPI or Histeresis (±0.25°C or ±0.5°C)
Communication Wireless, 868 Mhz + WIFI 2,4 GHz
Dimensions [mm] thermostat: 150 x 84 x 22 receiver: 96 x 96 x 27

REFERENCE:

DOWNLOAD MANUALS:

ENGO CONTROLS E901WIFI Wireless Internet Thermostat Wi-Fi User Guide

Engocontrols E901RXWIFI Wireless Thermostat QUICK GUIDE

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago