FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE.
Your new White-Rodgers 5-Day/1-Day/1-Day Digital Thermostat uses the technology of a solid-state microcomputer to provide precise time/temperature control. This thermostat offers you the flexibility to design heating and cooling programs that fit your needs.
This thermostat is intended for use with a low-voltage system; do not use this thermostat with a line-voltage system. If in doubt about whether your wiring is millivolt, line, or low voltage, have it inspected by a qualified heating and air conditioning contractor or electrician. Do not exceed the specification ratings. All wiring must conform to local and national electrical codes and ordinances. This control is a precision instrument and should be handled carefully. Rough handling or distorting components could cause the control to malfunction.
CAUTION
To prevent electrical shock and/or equipment damage, disconnect electric power to the system at the main fuse or circuit breaker box until installation is complete.
WARNING
Do not use on circuits exceeding specified voltage. Higher voltage will damage control and could cause shock or fire hazards. Do not short out terminals on the gas valve or primary control to test. Short or incorrect wiring will damage the thermostat and could cause personal injury and/or property damage. Thermostat installation and all components of the system shall conform to Class II circuits per the NEC code.
ELECTRICAL DATA
REMOVE OLD THERMOSTAT
ATTENTION!
This product does not contain mercury. However, this product may replace a unit that contains mercury. Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury. Wearing nonabsorbent gloves, take up the spilled mercury and place it into a container that can be sealed. If a cell becomes damaged, the unit should be discarded. Mercury must not be discarded in household trash. When the unit this product is replacing is to be discarded, place in a suitable container. Refer to www.white-rodgers.com for a location to send the product containing mercury.
ELECTRIC HEAT SYSTEMS
This thermostat is configured from the factory to operate a heat/ cool, fossil fuel (gas, oil, etc.), forced air system. It is configured correctly for any system that DOES NOT require the thermostat to energize the fan on a call for heat. If your system is an electric heat or heat-pump system that REQUIRES the thermostat to turn on the fan on a call for heat, locate the GAS/ELECTRIC switch on the thermostat base (see fig. 1) and switch it to the ELECTRIC position. This will allow the thermostat to energize the fan immediately on a call for heat. If you are unsure if the heating/ cooling system requires the thermostat to control the fan, and contact a qualified heating and air conditioning service person.
BATTERY LOCATION
2 “AA” alkaline batteries are included in the thermostat at the factory with a battery tag to prevent power drainage. You must remove the battery tag to engage the batteries. If BATT is displayed, the batteries are low and should be replaced with fresh “AA” Energizer® alkaline batteries. To replace batteries, install the batteries along the top of the base (see Fig. 1). The batteries must be installed with the positive (+) end to the left.
HYDRONIC (HOT WATER OR STEAM) HEATING SYSTEMS
This thermostat is set to operate properly with a forced-air heating system. If you have a hydronic heating system (a system that heats with hot water or steam), you must set the thermostat to operate properly with your system. Change the second option in the configuration menu to SL (see CONFIGURATION MENU, page 5).
NOTE
The following wiring diagrams show typical terminal identification and wiring. For proper installation, refer to the original manufacturer’s instructions.
NOTE Relay contacts shown are thermostatically operated. * The 24 Volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh “AA” Energizer® alkaline batteries.
Figure 2. Typical wiring diagram for single transformer systems
Figure 3. Typical wiring diagram for two-transformer systems with NO safety circuits
Figure 4. Typical wiring diagram for two-transformer systems with safety circuits in BOTH systems
If at any time during testing your system does not operate properly, contact a qualified service person. Turn on the power to the system.
Fan Operation
If your system does not have a G terminal connection, skip to Heating System.
CAUTION
To prevent compressor and/or property damage, if the outdoor temperature is below 50°F, DO NOT operate the cooling system.
Before you begin programming your thermostat, you should be familiar with its features and with the display and the location and operation of the thermostat buttons. Your thermostat
consists of two parts: the thermostat cover and the base. To remove the cover, pull it straight out from the base. To replace the cover, line up the cover with the base and press until the
cover snaps onto the base.
The configuration menu allows you to set certain thermostat operating characteristics to your system or personal requirements. Press RUN to make sure the thermostat is in the run program mode, then press PRGM and RUN at the same time to enter the configuration menu. The display will show the first item in the configuration menu.
The configuration menu table summarizes the configuration options. An explanation of each option follows. Press HOLD to change to the next menu item or press TIME to go back to the previous item in the menu. To exit the menu and return to the program operation, press RUN. If no keys are pressed within fifteen minutes, the thermostat will revert to normal operation.
Step | Press Button(s) | Displayed (Factory Default) | Press or to select: | COMMENTS |
1 | PRGM and RUN | HOLD (0:00) | 0 to 8 hrs (in 15 minute increments) | Select temporary Hold time |
2 | HOLD* | (FA) | SL | Select FA or SL (Fast or Slow) heating cycle rate |
3 | HOLD* | d-L (ON) | OFF | Select display backlight OFF or ON |
4 | HOLD* | E (ON) | OFF | Select Energy Management Recovery OFF or ON |
5 | HOLD* | Filter (000) | 0 to 1950 hours (in 50 hour increments) | Select filter replacement run time |
6 | HOLD* | LOC (OFF) | ON | Select compressor lockout OFF or ON |
7 | HOLD* | 0 HI (0) | 4 LO to 4 HI | Select temperature display adjustment higher or lower |
(F) | C | Select temperature display to F or C | ||
9 | HOLD* | 1 + 2 FA
(ON) | OFF | Select ON to start 2nd stage immediately when the setpoint is manually raised more than 3°F in HEAT or lowered more than 3°F in COOL from room temperature |
10 | RUN | Returns to normal operation |
Press HOLD to advance to next item or TIME to move backward to the previous item
MANUAL OPERATION
This section will help you plan your thermostat’s program to meet your needs. For maximum comfort and efficiency, keep the following guidelines in mind when planning your program.
SAMPLE
Heating/Cooling Schedule Plan (Factory Program)
Period | WEEKDAYS (5 Day) | SATURDAY (1 Day) | SUNDAY (1 Day) | ||||
Start Time | Temp | Start Time | Temp | Start Time | Temp | ||
HEAT | 1ST | 6:00 AM | 70°F | 6:00 AM | 70°F | 6:00 AM | 70°F |
2ND | 8:00 AM | 62°F | 8:00 AM | 62°F | 8:00 AM | 62°F | |
3RD | 5:00 PM | 70°F | 5:00 PM | 70°F | 5:00 PM | 70°F | |
4TH | 10:00 PM | 62°F | 10:00 PM | 62°F | 10:00 PM | 62°F | |
COOL | 1ST | 6:00 AM | 78°F | 6:00 AM | 78°F | 6:00 AM | 78°F |
2ND | 8:00 AM | 85°F | 8:00 AM | 85°F | 8:00 AM | 85°F | |
3RD | 5:00 PM | 78°F | 5:00 PM | 78°F | 5:00 PM | 78°F | |
4TH | 10:00 PM | 82°F | 10:00 PM | 82°F | 10:00 PM | 82°F |
Look at the factory preprogrammed times and temperatures are shown in the sample schedule. If this program will suit your needs, simply press the RUN button to begin running the factory preset program. If you want to change the preprogrammed times and temperatures, follow these steps. Determine the time periods and temperatures for your weekday and weekend programs. You must program four periods for both the weekday and weekend programs. However, you may use the same heating and cooling temperatures for consecutive time periods. You can choose start times, heating temperatures, and cooling temperatures independently for both weekday and weekend programs (for example, you may select 5:00 AM and 70° as the weekday 1st-period heating start time and temperature, and also choose 7:00 AM and 76° as the weekday 1st period cooling start time and temperature). Use the following table to plan your program time periods and the temperatures you want during each period. Fill in the complete table to have a record of your programs
Heating/Cooling Schedule Plan
Period | WEEKDAYS (5 Day) | SATURDAY (1 Day) | SUNDAY (1 Day) | ||||
Start Time | Temp | Start Time | Temp | Start Time | Temp | ||
HEAT | 1ST | ||||||
2ND | |||||||
3RD | |||||||
4TH | |||||||
COOL | 1ST | ||||||
2ND | |||||||
3RD | |||||||
4TH |
Entering Your Program
Follow these steps to enter the heating and cooling programs you have selected.
Set Current Time and Day
Enter Heating Program
CAUTION
If the outside temperature is below 50°F, disconnect power to the cooling system before programming. Energizing the air conditioner compressor during cold weather may cause personal injury or property damage.
CHECK YOUR PROGRAMMING
Follow these steps to check your thermostat programming one
final time before beginning the thermostat operation.
YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY
Reset Operation
If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation you can reset the thermostat by pressing, and TIME at the same time. This also resets
the factory defaults to the configuration menu and program. If the thermostat has power, has been reset, and still does not function correctly contact your heating/cooling service person
or place of purchase. Batteries For optimum performance, we recommend replacing the batteries once a year with fresh “AA” Energizer® alkaline batteries.
Symptom | Possible Cause | Corrective Action | |
No Heat/No Cool/No Fan | 1. | Blown fuse or tripped circuit breaker. | Replace fuse or reset breaker. |
(common problems) | 2. | Furnace power switch to OFF. | Turn switch to ON. |
3. | Furnace blower compartment door or | Replace door panel in proper position to engage | |
4. | panel loose or not properly installed. | safety interlock or door switch. | |
No Heat | 1. | Pilot light not lit. | Re-light pilot. |
2. | System Switch not set to Heat. | Set System Switch to Heat and raise setpoint above room temperature. | |
3. | Loose connection to thermostat or system. | Verify thermostat and system wires are securely attached. | |
4. | Furnace Lock-Out Condition. Heat may also | Many furnaces have safety devices that shut the system down when | |
be intermittent. | a lock-out condition occurs. If the heat works intermittently contact | ||
5. | Heating System requires service or | the furnace manufacturer or local service person for assistance. | |
thermostat requires replacement. | Diagnostic: Set System Switch to Heat and raise the setpoint above | ||
room temperature. Within a few seconds the thermostat should make | |||
a soft click sound. This sound usually indicates the thermostat is | |||
operating properly. If the thermostat does not click, try the reset | |||
operation listed above. If the thermostat does not click after being | |||
reset contact your heating and cooling service person or place of | |||
purchase for a replacement. If the thermostat clicks, contact the | |||
furnace manufacturer or a service person to verify the heating system | |||
is operating correctly. | |||
No Cool | 1. 2. 3. | System Switch not set to Cool. Loose connection to thermostat or system. Cooling System requires service or thermostat requires replacement. | Set System Switch to Cool and lower setpoint below room temperature. Verify thermostat and system wires are securely attached. Same procedure as diagnostic for No Heat condition except set the thermostat to Cool and lower the setpoint below the room temperature. There may be up to a five minute delay before the thermostat clicks in Cooling if the compressor lock-out option is selected in the configuration menu (Item 6). |
Heat, Cool or Fan Runs Constantly. | 1. 2. 3. 4. | Fan Switch set to Fan On. Possible short in wiring. Possible short in thermostat. Possible short in Heat/Cool/Fan system. | Check each wire connection to verify they are not shorted or touching together. No bare wire should stick out from under terminal screws. Try resetting the thermostat as described below. If the condition persists the manufacturer of your system or service person can instruct you on how to test the Heat/Cool system for correct operation. If the system operates correctly, replace the thermostat. |
Furnace Cycles Too Fast or Too Slow (narrow or wide temperature swing) | 1. | The location of the thermostat and/or the size of the Heating System may be influencing the cycle rate. | Item 2 in the Configuration Menu is the adjustment that controls the cycle rate. If an acceptable cycle rate is not achieved using the FA (Fast) or SL (Slow) adjustment contact a local service person for additional suggestions. |
Cooling Cycles Too Fast or Too Slow (narrow or wide temperature swing) | 1. | The location of the thermostat and/or the size of the Cooling System may be influencing the cycle rate. | The cycle rate for cooling is fixed and can not be adjusted. Contact a local service person for suggestions. |
Thermostat Setting and Thermometer Disagree | 1. | Thermostat thermometer setting requires adjustment. | The thermometer can be adjusted +/- 4 degrees as listed in item 7 of the Configuration Menu. No other adjustment is possible. |
Clock Loses or Gains Time | 1. | Loss of power to thermostat and low batteries. | The thermostat will maintain its program in memory even with no power/no batteries but the clock time will be incorrect when power is restored. See No Heat/No Cool/No Fan (common problems) above for items to check in the system. |
Heat or Cool Starts Early | 1. | EMR activated | See Configuration Menu (Item 4). |
Thermostat Does Not Follow | 1. | AM or PM set incorrectly in program. | Check current clock and program settings including the AM or PM |
Program | 2. | AM or PM set incorrectly on the clock. | designations for each time period. If a voltage spike or static discharge |
3. | Voltage spike or static discharge. | occurs use the Reset Operation listed above. | |
Blank Display and/or Keypad Not Responding | 1. 2. | Loss of power and dead batteries. Voltage Spike or Static Discharge. | Replace batteries and check heat/cool system for proper operation. If a voltage spike or static discharge occurs use the Reset Operation listed above. |
White-Rodgers is a division of Emerson Electric Co.
The Emerson logo is a trademark and service mark 8 of Emerson Electric Co.www.white-rodgers.com www.emersonclimate.com
Download Manual: EMERSON White Rodgers 1F81 Programmable Heat Pump Thermostat Installation and Operation Instructions
EMERSON White Rodgers 1F81 Programmable Heat Pump Thermostat Installation and Operation Instructions
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…