Emerson

EMERSON White Rodgers 1F81 Programmable Heat Pump Thermostat CONFIGURATION AND TYPICAL WIRING DIAGRAMS

EMERSON White Rodgers 1F81 Programmable Heat Pump Thermostat

Configuration Menu

Step 1F81-261

Press Button(s)

1F83-261

Press Button(s)

Displayed (Factory Default) Press or to select: COMMENTS
1 PRGM

and RUN

N/A HOLD (0:00) 0 to 8 hrs (in

15 minute increments)

Select temporary Hold time
2 HOLD* Set SYSTEM

switch to OFF and Press and

(FA)

SL Select FA or SL (Fast or Slow) heating cycle rate
3 HOLD* and d-L (ON) OFF Select display backlight OFF or ON
4 HOLD* N/A E (ON) OFF Select Energy Management Recovery OFF or ON
5 HOLD* and Filter (000) 0 to 1950 hours

(in 50 hour increments)

Select filter replacement run time
6 HOLD* and LOC (OFF) ON Select compressor lockout OFF or ON
7 HOLD* and 0 HI

(0)

4 LO to

4 HI

Select temperature display adjustment higher or lower
8 HOLD* and °(F) °C Select temperature display to °F or °C
9 HOLD* Set SYSTEM

switch to HEAT

or COOL

1 + 2

FA

 

(ON)

OFF Select ON to start 2nd stage immediately when the setpoint is manually raised more than 3° F in HEAT or lowered more than 3° F in COOL from room temperature
10 RUN N/A Returns to normal operation

* Press HOLD to advance to next item or TIME to move backward to the previous item

NOTE
The following wiring diagrams show typical terminal identification and wiring. For proper installation, refer to the original manufacturer’s instructions.
Relay contacts shown are thermostatically operated.

WIRING DIAGRAMS

Reset Operation: 1F81-261
If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat by pressing , and TIME at the same time. This also resets the factory defaults to the configuration menu and program. If the thermostat has power, has been reset and still does not function correctly, contact your heating/cooling service person or place of purchase.


Reset Operation: 1F83-261
If a voltage spike or static discharge blanks out the display or causes erratic thermostat operation, you can reset the thermostat by pressing , and move the SYSTEM switch from OFF to HEAT at the same time. This also resets the factory defaults to the configuration menu. If the thermostat has power, has been reset and still does not function correctly, contact your heating/cooling service person or place of purchase.

* The 24 Volt neutral connection to terminal C on the thermostat is not required if you replace the batteries once a year with fresh “AA” Energizer® alkaline batteries.

REFERENCE:

Download Manual: EMERSON White Rodgers 1F81 Programmable Heat Pump Thermostat CONFIGURATION AND TYPICAL WIRING DIAGRAMS

EMERSON White Rodgers 1F81 Programmable Heat Pump Thermostat CONFIGURATION AND TYPICAL WIRING DIAGRAMS

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago