EMERSON White-Rodgers 1D56-310 Thermostat Instruction Manual

EMERSON White-Rodgers 1D56-310 Thermostat Instruction Manual

WHITE-RODGERS

 

Installation Instructions  for:
Horizontal	1D56-310, -347
Snap-Action	1D56W-347
Vertical	1E56-301, -444
Sealed Mercury Cell	1E56W-444
Horizontal	1F56-301
Sealed Mercury Cell	1F56-306, -444
	1F56W-444

YOUR THERMOSTAT REPLACES

System	Models
Standard Heating & Cooling Systems – 4 or 5 wires Standard Heat Only Systems Standard Central Air Conditioning Gas or Oil Heat Hydronic (Hot Water) Zone Heat – 2 wires	All Models
Electric Furnace Heat Pump (No Aux or Emergency Heat)	1D56-347, 1D56W-347, 1E56-444, 1E56W-444, 1F56-306, -444, 1F56W-444
Heat Pump (with Aux or Emergency Heat) Baseboard Electric Heating or Line Voltage (120 or 240 Volt) Millivolt Heat Only Systems – Floor or Wall Furnaces Hydronic (Hot Water) Zone Heat – 3 wires	None

PREPARATIONS

Assemble tools required: power drill, flat blade screwdriver, wire cutter/stripper, level. Failure to follow and read all instructions carefully before installing or operating this control could cause personal injury and/or property damage.

THERMOSTAT FEATURES

 

CAUTION

To prevent electrical shock and/or equipment damage, disconnect electrical power to the system at the main fuse or circuit breaker until installation is complete. Before removing wires from old thermostat’s switching subbase, label each wire with the terminal designation it was removed from.

1. Remove Old Thermostat: A standard heat/cool thermostat consists of three basic parts:
2. The cover, which may be either a snap-on or hinge type.
3. The base, which is removed by loosening all captive screws.
4. The switching subbase, which is removed by unscrewing the mounting screws that hold it on the wall or adaptor plate.

Make a note here of the anticipator setting on the old thermostat for future reference and use in step 5. The heat anticipator pointer, if adjustable, will be set at one of a series of numbers representing the current rating of the primary control in your furnace. The number will be one of the following: .2, .4, .8, etc. or 0.2, 0.4, 0.8, etc.

REMOVING OLD THERMOSTAT

• If no heat anticipator/indication is showing, do not be concerned; move on to the next step.
• This product may or may not contain mercury. Also, this product may replace a unit that contains mercury.
• Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury.
• Wearing non-absorbent gloves, take up the spilled mercury and place into a container that can be sealed.
• If a cell becomes damaged, the unit should be discarded.
• Mercury must not be discarded in household trash.
• When the unit this product is replacing is to be discarded, place in a suitable container and return to White-Rodgers at 2895 Harrison St., Batesville, AR 72501 for proper disposal.

MOUNTING AND WIRING

WARNING

Do not use on circuits exceeding specified voltage. Higher voltage will damage control and could cause shock or fire hazard. Do not short out terminals on gas valve or primary control to test. Short or incorrect wiring will damage the thermostat and could cause personal injury and/ or property damage. Thermostat installation and all components of the system shall conform to Class II circuits per the NEC code.

• Remove base from subbase: Loosen the screws on the base and
• Mount switching subbase: Use the screws provided to mount the subbase and adaptor plate (optional) to wall
• Attach wires to appropriate terminals:
• For two wire systems (Heat Only or Cool Only). If you have a two-wire Heat Only system, attach one wire to RH and one to wire W.
• If you have a two-wire Cool Only system, attach one wire to RC and one to wire to Leave the factory-installed jumper between RC and RH attached. Tighten any unused terminals securely.
• If your system has more than two wires: Use the cross-reference chart to determine the correct wire
• If you have a four-wire heat/cool system leave the factory-installed jumper between RC and RH attached
• Electric heat or single-stage heat pump systems: 1F56-306 energizes the fan on call for heat.
• Other thermostats are configured from the factory to operate a heat/ cool, fossil fuel (gas, oil, ) forced air system.
• This is correct for any system that DOES NOT require the thermostat to energize the fan on a call for heat.
• If your system is an electric heat or heat pump system that REQUIRES the thermostat to turn on the fan on a call for heat, remove the yellow factory-installed jumper wire from the Y terminal and connect it to the A terminal.
• This will allow the thermostat to energize the fan immediately on a call for heat.
• If you are unsure if the heating system requires the thermostat to control the fan, contact a qualified heating and air conditioning service person.
• For single stage heat pump applications (no Auxillary heat), install a short jumper wire (not included) across terminals W and Y.
• If the system has a reversing valve connection energized in Cooling, attach it to O. If the system has a

Mounting Screw

Hole in Wall Mounting Screw reversing valve connection energized in Heating, attach it to B (see Fig. 4). This thermostat will not provide multi-stage heating or cooling.

Thermostat subbase

▲!   CAUTION To prevent electrical shock and/or equipment damage, disconnect electrical power to the system at the main fuse or circuit breaker until installation is complete.

REMOVING OLD THERMOSTAT

Mount Thermostat Base: Gently push excess wire back into the wall opening and plug hole with a fire-resistant material, such as fiberglass insulation to prevent drafts from affecting the thermostat Mount the thermostat base to the subbase using the three captive screws on the thermostat base. Tighten the screws securely.   Remove the paper tag from the plastic contact cover. Proceed to Step #5.

SET HEAT ANTICIPATOR

Set the anticipator to match the setting of your old thermostat you noted in Step 3, or, the anticipator should be set to match the current rating stamped on your main heating control. The heat anticipator is adjustable from 0.15 to 1.2 amps. Adjust the anticipator by rotating the contact arm  The anticipator setting is indicated by the numbers on the base that the pointer points to. If you are unsure where to set the anticipator contact the heater manufacturer for a recommended setting. Move the pointer counterclockwise to\ lengthen heating system cycles; move clockwise to shorten heating cycles. Adjustments should not be greater than 1/2 marking at a time. Snap on Cover: Carefully align the cover with the base and snap the cover onto the base.

NEW THERMOSTAT OPERATION

This thermostat is easy to operate. After power is turned on, use the system switch to select either heating or cooling, or to turn the heating/cooling system off. Use the fan switch to control fan operation. When the fan switch is in the AUTO position, the fan will cycle with the heating or cooling system (the fan will not run if the system switch is in the OFF position and the fan switch is in the AUTO position). When the fan switch is in the N position, the fan will run continuously, regardless of system switch position (even if he system switch is set to OFF, the fan will run if the fan switch is in the ON position).

Figure 2. Typical wiring for single transformer heating/cooling system

Figure 3. Typical wiring for two-transformer heating/cooling system

SPECIFICATIONS

• Switch Rating…………………………………… 24 VAC (30 VAC max.)
• Heating…………………………………………….. 0.15 to 1.2 Amps
• Cooling…………………………………………….. 0 to 1.5 Amps

Anticipator Rating

• Heating…………………………………………….. Adjustable from 0.15 to 1.2 Amps
• Cooling…………………………………………….. Fixed

THERMAL DATA

• Temperature Range…………………………. 50°F to 90°F (10°C to 32°C)
• Operating Humidity Range……………… 0 – 90% non-condensing

TROUBLESHOOTING

Symptom	Possible Cause	Corrective Action
No Heat/No Cool/No Fan (common problems)	1.  Blown fuse or tripped circuit breaker. 2.  Furnace power switch to OFF. 3.  Furnace blower compartment door or panel loose or not properly installed.	Replace fuse or reset breaker. Turn switch to ON. Replace door panel in proper position to engage safety interlock or door switch.
No Heat	1.  Pilot light not lit. 2.  Broken or melted anticipator wire.   3.  Loose connection to thermostat or system. 4.  Thermostat or heating system requires replacement or service.   5.  System Switch not set to Heat.	Re-light pilot. Excessive current or dead short in system. Have a qualified service person check the system before replacing thermostat. Verify thermostat and system wires are securely attached. Your furnace manufacturer or service person can describe how to test the heating system to verify it is operating correctly. If the heating system is capable of operation and the no heat condition persists, replace the thermostat. Set System Switch to Heat and raise temp above room temp.
Intermittent Heat	1. Furnace Lock-Out Condition	Many furnaces have safety devices that shut the system down when a lock-out condition occurs. If the heat works intermittently contact the furnace manufacturer or local service person for assistance.
No Cool	1.  Loose connection to thermostat or system. 2.  Thermostat or cooling system requires replacement or service.   3.  System Switch not set to Cool.	Verify thermostat and system wires are securely attached. Your cooling system manufacturer or service person can describe how to test the cooling system to verify it is operating correctly. If the cooling system is capable of operation and the no cooling condition persists, replace the thermostat. Set System Switch to Cool and lower temp below room temp.
Heat, Cool or Fan Runs Constantly.	1.  Possible short in wiring. 2.  Possible short in thermostat. 3.  Possible short in heat/cool/fan system.	Check each wire connection to the thermostat to verify it is neatly looped under the terminals. No extra wire should stick out from under the terminals.
Furnace Cycles Too Fast or Too Slow Narrow or wide temperature swing	See Step 5, Adjusting the Anticipator.	The anticipation setting is the only adjustment that effects the heating cycle rate. If an acceptable cycle rate is not achieved using the anticipator contact a local service person for additional suggestions. The location of the thermostat, size of the Heat/Cool System and current draw can influence the cycle rate.
Cooling Cycles Too Fast or Too Slow (narrow or wide temperature swing)	1.  Poor thermostat location for sensing room temperature. 2.  Cooling system over or undersized. 3.  Excessive Current draw influencing thermostat.	The cycle rate for cooling can not be adjusted. The location of the thermostat, size of the Cool system and current draw can influence the cycle rate. Contact a local service person for suggestions.
Thermostat Setting and Thermostat Thermometer Disagree	1.  Thermostat thermometer setting requires adjustment. 2.  Thermostat setting lever requires calibration.	The thermometer can be adjusted by using a standard slotted screwdriver. Turn the thermometer pointer screw located inside the front cover to change the setting. For calibrating the setting lever contact a local heating and cooling service person.
Adjusting Thermometer	1. Thermostat thermometer disagrees with other room thermometers.	The thermometer on the thermostat is accurately calibrated at our factory but you can adjust it by using a standard slotted screwdriver. Turn the thermometer pointer screw located inside the front cover to change the setting.

REFERENCE

Download Manual

EMERSON 1D56-310 White-Rodgers Low Voltage Horizontal Mounting Thermostat Instruction Manual

EMERSON White-Rodgers 1D56-310 Thermostat