Read this manual carefully before beginning operation with your Daikin Home Controls (DHC) accessories. Keep the manual so you can refer to it at a later date if you need to. If you hand over the accessory to other persons for use, hand over this manual as well.
Symbols used:
Attention!
This indicates a hazard.
Please note:
This section contains important additional information.
This accessory is part of the DHC ecosystem and communicates with a dedicated wireless connection.
All accessories of the ecosystem can be configured comfortably and individually via the ONECTA app. The available functions provided by the DHC ecosystem in combination with other accessories are described in the DHC Application Guide.
All current technical documents and updates can be found on the product pages: https://qr.daikin.eu/?N=EKRRVATR2BA
The DHC Radiator Thermostat enables time-controlled regulation of the room temperature via a heating schedule with individual time slots. For precise regulation of the room temperature, the DHC Room Thermostat can measure the actual temperature of a room and transmit the data to the DHC Radiator Thermostat.
You can comfortably control the DHC Radiator Thermostat in connection with a DHC Access Point via the free ONECTA app.
The DHC Radiator Thermostat fits all common radiator valves and is easy to mount, without having to drain any water or intervene in the heating system. With the additional boost function, cool rooms can be heated quickly by opening the heating valve.
Accessory overview (see figure 1):
Display overview (see figure 2):
Read this entire section before starting to connect other accessories.
To integrate the DHC Radiator Thermostat into your eco-system and enable it to communicate with other accessories, you must connect them first.
You can connect the DHC Radiator Thermostat to the DHC Access Point via the ONECTA app. It is also possible to create a direct connection to other DHC accessories. For further information on a direct connection, see the DHC Application Guide.
Connecting to the DHC Access Point
You can fix the DHC Room Thermostat to a wall with:
You can also mount the DHC Room Thermostat on a flush-mounted box.
Adhesive strip mounting
To mount the DHC Room Thermostat using the adhesive strips, proceed as follows:
Screw mounting
To mount the DHC Room Thermostat with screws, proceed as follows:
Flush-mounted box mounting
You can mount the DHC Room Thermostat on a flush-mounted box using the screw holes (see figure 11).
If the accessory is mounted to a flush-mounted box, there may be no open conductor ends.
If changes or works have to be made on the house installation (e.g. extension, bypass of switch or socket inserts) or the low-voltage distribution for mounting or installing the accessory, the following safety instruction must be considered:
Only to be installed by persons with the relevant electro-technical knowledge and experience!*
Incorrect installation can put your own life at risk and the lives of other users of the electrical system at. The incorrect installation also means that you are running the risk of serious damage to property, e.g. because of a fire. You may be personally liable in the event of injuries or damage to property.
Contact an electrical installer!
*Specialist knowledge required for installation:
The following specialist knowledge is particularly important during installation:
The configuration of the accessory can be set up completely in the ONECTA app. For further information on configura-tion of the accessory without using the DHC Access Point, see the DHC Application Guide.
The following modes and settings can be adjusted:
6.1 | AUTO | Automatic mode |
6.2 | MANU | Manual mode |
6.3 | Offset | Offset temperature (not yet available) |
6.4 | Prg | Programming a schedule |
6.5 | Operating lock (not yet available) | |
6.6 | Holiday mode |
In automatic mode, the temperature is controlled in ac-cordance with the set heating schedule. Manual changes are activated until the next point at which the schedule changes. Afterwards, the defined schedule will be activated again.
In manual mode, the temperature is controlled in accor-dance with the current temperature set via the push-but-tons (E + F). The temperature remains activated until the next manual change.
As the temperature is measured on the DHC Radiator Thermostat, the temperature distribution can vary through-out a room. To adjust this, a temperature offset of ±3.5 °C can be set. If a nominal temperature of e.g. 20 °C is set but the room presents with only 18 °C, an offset of -2.0 °C needs to be set.
This setting is not yet available in the ONECTA app and cannot be changed for the moment.
Programming a schedule
You can create a schedule with time slots for heating and cooling according to your personal needs.
Operating lock (not yet available)
Operation of the accessory can be locked to avoid settings being changed unintended (e.g. through involuntary touching). This setting is not yet available in the ONECTA app and cannot be changed for the moment.
Holiday mode
Holiday mode can be activated in the ONECTA app. It will put your system into standby. The holiday mode is visualized on your Daikin Altherma and on the Air Conditioning units in the ONECTA App.
For further information, see the DHC Application Guide.
After connecting and mounting the DHC Radiator Thermostat, simple operations are available directly on the accessory.
If the symbol for empty batteries (
To replace the batteries of the accessory, proceed as follows
Attention! There is a risk of explosion if the battery is not replaced correctly. Replace only with the same or equivalent type. Never recharge nonrechargeable batteries. Do not throw the batteries into a fire. Do not expose batteries to excessive heat. Do not short-circuit batteries. Doing so will present a risk of explosion.
Used batteries should not be disposed of with regular domestic waste! Instead, take them to your local battery disposal point.
Provided that the voltage value permits it, the accessory will remain ready for operation even if the battery voltage is low. Depending on the particular load, it may be possible to send transmissions again repeatedly, once the batteries have been allowed a brief recovery period.
If the voltage drops too far during transmission, the empty battery symbol(
The wireless DHC accessories operate in the following frequency bands:
In order to safeguard the operation of all devices working in this range, it is legally required to limit the transmission time of devices. Limiting the transmission time minimizes the risk of interference.
The ‘duty cycle’ is the maximum transmission time. It is the ratio of the time that a device is actively transmitting in comparison to the measurement period (1 hour), and is expressed as a percentage of 1 hour.
If the total amount of allowed transmission time is reached, the DHC accessory will stop transmitting until the time limit is reached.
For example, when a device has a duty cycle limit of 1%, it is only allowed to transmit 36 seconds in 1 hour. After this, it will stop transmitting until the 1 hour limit is reached. DHC accessories fully comply to this limitation and use 2 frequency bands with a duty cycle of respectively 1 % and 10%.
During normal operation of the DHC accessories, this limit is not usually reached. However, it is possible that the limit is reached during start-up or during a fresh installation of asystem. In this case, the LED of the accessory lights up red. It may be non-responsive for a short period (max. 1 hour), until the time restriction for transmission has expired. After this period, it will operate normal again.
Error and flashing codes | Meaning | Solution |
Battery symbol ( | Battery voltage too low | Replace the batteries of the accessory (see “8 Replacing batteries” on page 28). |
Antenna symbol flashing ( | Communica tion problem with DHC Access Point or connected accessory | Check the connection with the DHC Access Point or the connected accessory. |
Lock symbol ( | Operating lock activated | Deactivate the op- erating lock via the app or the menu. |
Short orange flashing | Radio transmission/attempting to transmit/data transmission | Wait until the transmission is completed. |
1x long green lighting | Operation confirmed | Continue operation. |
Error and flashing codes | Meaning | Solution |
Short orange flashing (every 10 seconds) | Connection mode active | Follow the instructions in the app to add an accessory (see “5.1 Connecting DHC accessories” on page 18). |
Short orange lighting (after green or red confirmation) | Batteries empty | Replace the batteries (see “8 Replaceing batteries” on page 28). |
1x long red lighting | Transmission/ operation failed or duty cycle limit is reached | Try again (see “9.2 Duty cycle” on page 30). |
6x long red flashing | Accessory defective | Contact your reseller. |
1x orange and 1 x green lighting (after inserting batteries) | Test LED | After the test LED has stopped, you can continue. |
The factory settings of the accessory can be restored. If you do this, you will lose all your settings.
To restore the factory settings of the accessory, proceed as follows:
The accessory does not require you to carry out any maintenance other than replacing the battery when necessary. Enlist the help of an expert to carry out any repairs.
Clean the accessory using a soft, lint-free cloth that is clean and dry. You may dampen the cloth a little with lukewarm water in order to remove more stubborn marks. Do not use any detergents containing solvents, as they could corrode the plastic housing and label.
Radio transmission is performed on a non-exclusive transmission path, which means that there is a possibility of interference occurring. Interference can also be caused by switching operations, electrical motors, or defective electrical devices. The range of transmission within buildings can differ greatly from that available in the open air. Besides the transmitting power and the reception characteristics of the receiver, environmental factors such as humidity in the vicinity have an important role to play, as do on-site structural/screening conditions.
Hereby, Daikin Europe N.V. declares that the radio equipment type DHC EKRRVATR2BA is in compliance with Directive 2014/53/EU. The original declaration of conformity is available from the EKRRVATR2BA product pages. https://qr.daikin.eu/?N=EKRRVATR2BA
Subject to technical changes.
Instructions for disposal
Do not dispose of the device with regular domestic waste! Electronic equipment must be disposed of at local collection points for waste electronic equipment in compliance with the Waste Electrical and Electronic Equipment Directive.
Information about conformity
The CE sign is a free trading sign addressed exclusively to the authorities and does not include any warranty of any properties. For technical support, please contact your specialist dealer.
Free download of the ONECTA app!
Download Manual
Daikin EKRCTRDI2BA Room Thermostat Installation Guide
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…