CAUTION Follow the Installation Instructions before proceeding. Set the thermostat mode to “OFF” prior to changing settings in setup or restoring Factory Defaults.
This equipment has been tested and found to comply with the limits for an intentional radiator, pursuant to Part 15, subpart C of the FCC rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference in radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Notice: Only peripherals complying with FCC limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Daikin is likely to result in interference to radio and TV reception. Changes or modifications to the product, not expressly approved by Daikin could void the user’s authority to operate the equipment.
FCC – INDOOR Mobile Radio Information:
To comply with FCC/IC RF exposure limits for general population / uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This Device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
We, Daikin, declare under our sole responsibility that the device to which
this declaration relates: Complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The FCC responsible party is Goodman Manufacturing Company, L.P., and may be contacted by calling (713)-861-2500, or at 19001 Kermier Rd., Waller, TX 77484. www.GoodmanMFG.com
This color touchscreen has the ability to receive updates to its firmware. Periodically firmware updates are released by the manufacturer to add features and/or performance enhancements. This manual was produced reflecting the most current firmware/feature set at the time of publication, firmware rev. 4.04. Firmware releases after rev. 4.04 may not be adequately depicted in this manual. Please refer to the appropriate website or contact your place of purchase to learn about changes to the thermostat after firmware release 4.04.
During Setup and Programming
Press the WARMER or COOLER buttons to modify the selection. Press the MODE button to advance and confirm through the setup steps.
Setting the Clock and Day*
Not available when wi-fi module is present.
Press the SET CLOCK button. Adjust the clock using the WARMER or COOLER buttons. Press MODE to advance to the day setting. Adjust the day using the WARMER or COOLER buttons. Press the SET CLOCK button to confirm settings.
TIP: To adjust the time by hours press and hold the FAN button while pressing the WARMER or COOLER buttons.
Select mode by pressing the MODE button.
Selecting your desired temperature
Using the Fan Button
Fan On indicates constant fan operation. You may turn the fan on even if the thermostat is in the OFF mode. Pressing the FAN button toggles this feature on or off. If you don’t see “Fan On”, the fan is in auto mode and will only turn on during a heat or cool demand.
Viewing the Temperature Sensors
REMOTE/SUPPLY TEMP
Press the Accessory Status button to view linked wireless wired sensors and other accessories. Press the Accessory Status button to return to the main screen.
Remove and Replace the old thermostat
To install the thermostat properly, please follow these step by step instructions. If you are unsure about any of these steps, call a qualified technician for assistance.
If the terminal designations on your old thermostat do not match those on the new thermostat, refer to the chart below or the wiring diagrams that follow.
Wire from the old thermostat terminal marked | Function | Install on the new thermostat connector marked |
G or F | Fan | G |
Y1, Y | Cooling | Y1 |
W1, W | Heating | W1/0/B |
Rh, R, M, Vr, A | Power | R |
C | Common | C |
O/B | Rev. Valve | W1/O/B* |
W2 | 2nd Stage Heat | W2 |
Ck1 | Dry Contact Switch | DRY CONTACT |
CKGND | Dry Contact Switch | DRY CONTACT |
Note: O/B is used if your system is a Heat Pump.
IMPORTANT: This thermostat requires both R (24 VAC Return) and C (24 VAC Common) be connected to the backplate terminals.
Ensure which switch is correct for your system. Dip switches are located on the back of the thermostat.
For Heat Pump Only
When the GAS/EL or HP dip switch is configured for HP, this dip switch (O or B) must be set to control the appropriate reversing valve. If O is chosen, the W1/O/B terminal will energize in cooling. If B is chosen, the W1/O/B terminal will energize in heating.
This dip switch configures the thermostat to control a conventional gas/electric system or a heat pump. If your system is anything other than a heat pump, leave this switch set for GAS/EL.
Conventional Heating and Cooling Systems
Heat Pump Systems
Dry Contact
The technician setup is a diagnostic feature that enables testing of all outputs. To enter Technician Setup, press and hold the SETUP button for 10 seconds until all the icons appear. Follow the next steps to view settings and test equipment.
How to Change Settings in the Setup Screens
To enter Advanced Setup, press the SETUP button, then press MODE. Use the WARMER or COOLER buttons to adjust the value of your selection. Press MODE to advance to the next setup step. Press SETUP again to leave the setup screens.
Backlight (setup step 3)
Backlight Intensity Level (setup step 4)
The backlight can be adjusted between Off and seven levels of brightness.
Night Dimmer (setup step 5)
Selecting On allows for automatic dimming of the display at night.
Night Dimmer Brightness (setup step 6)
Off through seven levels of brightness
Night Dimmer Start Time (setup step 7)
12:00 am to 12:00 am
Night Dimmer Stop Time (setup step 8)
12:00 am to 12:00 am
Language (Setup Step 15)
Setup step instructions on the scrolling display can be set for English, Spanish, or French. Press the SETUP button, then press MODE repeatedly until the Language setup step appears. Use the WARMER or COOLER buttons to make a selection. Press MODE to advance to the next step. Press SETUP to leave the setup screens.
Scrolling Display Method (Setup Step 16)
This option allows the user to choose how the scrolling text is displayed. Options are:
Press the SETUP button, then press MODE repeatedly until the Scrolling Method setup step appears. Use the WARMER or COOLER buttons to make selection. Press MODE to advance to the next step. P ress SETUP to leave the setup screens.
Example of “Whole Words Centered”:
The Vacation feature allows the thermostat to use temporary, energy-saving setpoints without having to change regular programming.
The HOME/AWAY feature allows for a one button press to bring in your stored unoccupied vacation settings. A subsequent press of the HOME/AWAY button restores the last used comfort settings.
When the VACATION button is pressed and the thermostat detects that a Wi-Fi module is installed:
Emergency Heat
The Emergency Heat function is only available if your thermostat is set to control a Heat Pump. To initiate the Emergency Heat feature, Press the EMERGCY button. During Emergency Heat operation the thermostat will turn on the fan and auxiliary stages of heat when there is a demand for heat. The compressor used for heating and all stages of cooling will be unavailable. To exit Emergency Heat, press the EMERGCY button.
The Accessory Status button allows the user to view the status of wired and wireless accessories. For many of the wireless devices this status includes: Battery Level, Signal Strength & Last Time Updated.
If there is an optional wireless module installed, the Accessory Setup button allows the user to link or connect wireless devices to the thermostat, or the thermostat to the network.
Wi-Fi Module
Please follow the instructions included with the Wi-Fi module to connect to an Access Point or view status. The general instructions are below.
If the WIFI is present on the display then the thermosat is connected to the Wi-Fi Access Point. If just the “dot” of this icon appears, then just the Wi-Fi module is recognized.
Press the Accessory Status button, then press either the Cooler button to view connected Wi-Fi sensors, OR press the Warmer button to view the Wi-Fi status and settings.
Press the Mode button to step through the connected sensors or the Wi-Fi status screens listed below.
At any time press the Accessory Status button to leave the status screens.
Press the Accessory Setup button to enter Wi-Fi or Skyport setup:
Press the Cooler button to configure Wi-Fi settings.
Press the Warmer button to join this thermostat to a Skyport account. If the theremostat is connected to Wi-Fi and the Internet, a Device ID will appear on the scrolling display of the thermostat. You will enter this code to add this thermostat to your Skyport account via a browser or the Skyport mobile app.
Note: To connect to Skyport Cloud Services, Setup Step #27 must be set to on.
These setup steps allow the user to monitor equipment runtimes and program service alerts. Service alerts are displayed in the scrolling marquee.
Service Filter Runtime (Setup Steps 9-10, 12-13)
To view, set, or reset System Runtimes, press the SETUP button, then press MODE. Press MODE to advance to the desired setup step. Use the WARMER or COOLER buttons to adjust the value of your selection. Press SETUP again to leave the setup screens.
UV Lamp Runtime (setup steps 11, 14)
Programming a Daily Schedule*
*not available when wi-fi module is present
To enter Time Period Programming screens, Press and hold PROGRAM until the scrolling prompt appears.
Select Day of Week to program – Press the WARMER or COOLER buttons to choose the day of the week to be Press MODE to advance to the next step.
Program Button
This thermostat features four programmable time periods per 24 hour day:
Morning, Day, Evening, and Night. The start time for each time period is adjustable. The stop time for each time period is the start time for the next period. Each time period, or day part may be individually disabled.
Select the Day to Program – Press the WARMER or COOLER to select the desired Day or Week Part in the case of 5-2 (weekday – weekend) programming.
Enable/Disable Morning Period – Press the WARMER or COOLER to select ON or OFF. If the default ON is selected, then the Morning period will run complete with the Mode and Set Points selected. If OFF is selected then the Morning day part will be skipped and the thermostat will use the next day part that is enabled.
Select Morning Mode – Press the WARMER or COOLER to select the desired mode, which includes OFF. You may be limited by the available modes in advanced Installer setup step#2. Press MODE to advance to the next step.
Select Morning Start Time – Press the WARMER or COOLER buttons to adjust the time of day desired. Press MODE to advance to the next step.
Select Morning Cool Setpoint – Press the WARMER or COOLER buttons to adjust the cool setpoint desired. This step will appear if Cool or Auto Mode was selected in the step where the Morning mode is specified. Press MODE to advance to the next step.
Select Morning Heat Setpoint – Press the WARMER or COOLER buttons to adjust the heat setpoint desired. This step will appear if Heat or Auto Mode was selected in the step where the Morning mode is specified. Press MODE to advance to the next step.
Repeat Enable, Mode, Start Time and Setpoint programming for Day, Evening, and Night.
“Copy Current Day to Next Day” is available – Press the UP button to Copy the current day’s program to the next day. Press Mode again to continue copying the following day.
Press the PROGRAM Button to exit Time Period Programming at any time.
How to Change Settings in the Setup Screens
To enter Advanced Setup, press the SETUP button, then press MODE. Use the WARMER or COOLER buttons to adjust the value of your selection. Press MODE to advance to the next setup step. Press SETUP again to leave the setup screens.
Selecting Your Time Period Schedule (setup step 1) T
his thermostat may be configured to be programmable or nonprogrammable.
Selecting Your Available Modes (setup step 2)
The Cycles Per Hour setting may limit the number of times per hour your HVAC unit may energize. For example, at a setting of 6 cycles per hour the HVAC unit will only be allowed to energize once every 10 minutes. The Cycles Per Hour limit may be overridden and reset by pressing the WARMER or COOLER buttons on the thermostat. Settings are No Limit, 2, 3, 4, 5, or 6.
Compressor Minimum Off Minutes (setup step 18)
This feature allows the user to set a minimum off time for the compressor. Settings are 5 mins., 3 mins., or 0 mins.
Minimum Heat/Cool Setpoint Difference (setup step 19)
This feature allows the user to set the minimum gap between Heat and Cool setpoints in AUTO mode. Select from 0 to 6. If setup step 2 is not set for AUTO-CHANGEOVER, this step will not appear.
Number of Heat Stages (setup step 20)
This setting assures proper stage callouts on the thermostat display for non-heat pump applications.
Number of Cool Stages (setup step 21)
This setting assures proper stage callouts on the thermostat display for non-heat pump applications.
Number of Aux Stages (setup step 22)
This feature is for heat pump application only. This feature allows for proper Aux Heat Staging. (0-2 stages)
Deadband Settings (setup step 23)
The Deadband is the number of degrees or minutes that the thermostat waits before it initiates the stages of heating or cooling.
Fahrenheit or Celsius (setup step 24)
This feature allows the thermostat to display temperature in Fahrenheit or Celsius.
Press Fan To Clear All Messages (setup step 37)
This feature allows the user to clear all current error messages from the display.
Dry Contact Polarity (setup step 25)
Dry Contact Use (setup step 26)
Skyport (setup step 27)
Set to ON to allow access to Skyport services or to OFF to not allow access to Skyport services.
Local API (setup step 28)
Set to ON to allow 3rd party software to interface with your thermostat such as home automation software.
Resetting the Thermostat to the Factory Default Settings
(for default values see page 39, Advanced SetupTable)
If, for any reason, you desire to return all the stored settings back to the factory default settings, follow the instructions below.
WARNING: This will reset all Time Period and Advanced Programming to the default settings. Any information entered prior to this reset may be permanently lost.
Overview
Daikin Digital thermostats support the handling of specific signals from the utility provider. The utility generated signals carry pricing information and/or setback actions that alter the comfort settings of the thermostat in order to reduce energy usage on demand. This is known as Automated Demand Response or ADR for short. You must register to participate
in a utility sponsored program, if offered by your local utility, to take advantage of this feature.
Skyport Cloud Services
From the web application the user will select Thermostat Settings from the left column. Then the Demand Response button is selected.
The Demand Response configuration page, shown below, is where the thermostat is configured to respond to the energy provider’s signals. It also sets operational parameters for the thermostat.
The left column of the ADR configuration page allows or prevents access by the utility. Here communication with the utility and your thermostat may be turned On or Off.
The selected utility will provide a Program ID.
The Account ID would normally be the occupants utility account number.
The right column of the ADR configuration page is where the occupant adjusts the operational parameters for ADR. The utility may send up to 3 types of ADR signals to Skyport. These are:
1) Pricing for the cost of energy, 2) An Offset to the occupants’ comfort setpoints, and 3) a signal to enforce discrete or Static setpoints.
The Maximum Cooling Setpoint and Minimum Heating Setpoints for ADR events are adjusted here.
The Static Settings are applied when the utility sends a signal to allow the occupant to enforce their own discrete temperature settings during an ADR event.
The Offset Settings allow the utility to modify the Cool or Heat setpoints by the value set here during an ADR event.
A Price Trigger setting allows the occupant to set the maximum cost of energy threshold. When this threshold is exceeded
the Price dependent action is enforced. This Price Trigger and Dependent action is enforced independent of an ADR event, as long as the utility sends ‘real-time’ pricing.
Selecting the Overview tab of the ADR page will cause a summary of ADR events to be displayed.
ADR (setup step 29)
Controls whether you want the thermostat to possibly respond to signals from the utility provider. Select ON to allow this and to have steps 30-36 appear.
Price Dependent Action (setup step 30)
Allows the user to determine what action is taken when the price rises above the set threshold. Note that the threshold price is only adjustable via Skyport.
Specifies the range of allowable setpoint adjustments to be enforced when any ADR signal has been received from the utility. Since you might be paying more for energy while an event is active, you can impose tighter limits on setpoint ranges that are only enforced during the event.
Specifies the setpoints that will come into use during an event when the PRICE DEPENDENT ACTION is set to OBSERVE STATIC SETPOINTS
Specifies how much the current setpoints in effect prior to an event will be altered during an event when the PRICE DEPENDENT ACTION is set to OBSERVE SETPOINT OFFSETS. The heat setpoint can be automatically lowered by 1 to 10 degrees while the cool setpoint can be automatically raised by 1 to 10 degrees
DISPLAY INDICATIONS WHEN AN ADR EVENT IS HAPPENING
After setting your desired values for use during an ADR event, the scrolling display will give a little information when an event is pending or active. For instance, when an ADR event has been sent to your thermostat, you might see ADR STARTS at 4:15 to notify you of a pending event. Once active, you might see ADR STOPS at 5:30. If you have configured a threshold for cost of energy past which you want to trigger an event, you will see PRICING EVENT on the display. When an event is active, you can press any of COOLER, WARMER or MODE buttons, followed by the WARMER to opt out of the event.
To prevent unauthorized use of the thermostat, the front panel buttons may be disabled. To disable, or ‘lock’ the keypad, press and hold the MODE button. While holding the MODE button, press the WARMER and COOLER buttons together. The
To unlock the keypad, press and hold the MODE button. While holding the MODE button, press the WARMER and COOLER buttons together. The
To enter Technician Setup, press and hold the SETUP button for 5 seconds. After all the icons appear, press MODE. The version number of the thermostat will appear in the scrolling text. Press MODE to advance to the next step. Use the WARMER or COOLER buttons to adjust the value of your selection. To leave Technician Setup, press SETUP.
Technician Setup is for diagnostic and testing purposes and is intended for use by a qualified technician. See page 15 for more detailed instructions.
Technician Setup contains the following options:
Step# Description | Pg# | Range | Df | |
1 | Prog Mode | 25 | Non, 1 Day, 5/2 Day, 7 Day | 7 |
2 | Available Modes | 25
16 | Heat/Cool/Auto/Off, Heat/Cool/Off, Heat/Off, Cool/Off | Heat/Cool/ Auto/Off |
3 | Backlight | 16 | On, Off | Off |
4 | Backlight Level | 16 | Off thru 7 levels of brightness | Level 5 |
5 | Night Dimmer | 16 | On/Off | Off |
6 | Night Dimmer Brightness | 16 | Off thru 7 levels of brightness | 2 (20%) |
7 | Night Dimmer Start Time | 16 | 12A-12A | 8:00P |
8 | Night Dimmer Stop Time | 16 | 12A-12A | 6:00A |
9 | Current Service Filter Runtime Hours | 21 | 0-1999 Hours | 0 |
10 | Current Service Filter Calendar Days | 21 | 0-720 Days | 0 |
11 | Current UV Lamp Calendar Days | 22 | 0-720 Days | 0 |
12 | Set Service Filter Runtime Hours | 21 | 0-1950 hours | 0 |
13 | Set Service Filter Calendar Days | 21 | 0-720 Days | 0 |
14 | Set UV Lamp Calendar Days | 22 | 0-720 Days | 0 |
15 | Language | 16 | English, Espanol, Francais | English |
16 | Scrolling Method | 17 | “L-R Slow, L-R Fast, Word L-R Slow, Word L-R Fast, Whole Word L Slow, Whole Word R Slow, Whole Word Ctr. Fast, Whole Word Ctr. Slow | Whole Word Center Fast |
17 | Cycles Per Hour | 26 | No Limit, 2, 3, 4, 5, 6 | 6 |
18 | Compressor Minimum Off Minutes | 26 | 0, 3, 5 Minutes | 5 |
19 | Min. Heat/Cool Setpoint Difference | 26 | 0 – 6 Degrees | 2 |
20 | Number of Heat Stages | 26 | 0 – 2 | 2 |
21 | Number of Cool Stages | 26 | 0 – 1 | 1 |
22 | Number of Aux Stages | 26 | 0, 1 | 0 |
23 | 1st Stage Deadband | 26 | 1 – 6 Degrees | 2 |
24 | F/C | 26 | Fahrenheit (F), Celsius (C) | F |
25 | Dry Contact Polarity | 27 | Open, Closed | Open |
26 | Dry Contact Use | 27 | Condensate, Vacation, FDD | Vacation |
27 | Skyport | 27 | On, Off | On |
28 | Local API | 27 | On, Off | Off |
29 | ADR | 33 | On, Off | Off |
Step# Description | Pg# | Range | Df | |
30 | Price Dependent Action | 33 | None, Observe Setpoint Offset, Observe Static Setpoints | None |
31 | Event Max Cool Setpoint | 33 | 65 – 85 | 85 |
32 | Event Min Heat Setpoint | 33 | 65 – 85 | 65 |
33 | Static Cool Setpoint | 33 | 65 – 85 | 78 |
34 | Static Heat Setpoint | 33 | 65 – 85 | 68 |
35 | Cool Setpoint Offset | 34 | 1 to 10 | 2 |
36 | Heat Setpoint Offset | 34 | -1 to -10 | -2 |
37 | Press Fan To Clear All Messages | 26 |
One-Year Warranty – This Product is warranted to be free from defects in material and workmanship. If it appears within one year from the date of original installation, whether or not actual use begins on that date, that the product does not meet this warranty, a new or remanufactured part, at the manufacturer’s sole option to replace any defective part, will be provided without charge for the part itself provided the defective part is returned to the distributor through a qualified servicing dealer.
THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of either defective parts or replacement parts. Such costs may be covered by a separate warranty provided by the installer.
THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION LOCATION AND BECOMES VOID UPON REINSTALLATION.
LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH THE LIMITED WARRANTY IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED, ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER.
ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING HOURS. ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY.
THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:
This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
see page 23
DAY | PERIOD | START TIME | COOL | HEAT | |
MONDAY | Morning | ||||
Day | |||||
Evening | |||||
Night | |||||
TUESDAY | Morning | Copy Mon to Tues No Yes | |||
Day | |||||
Evening | |||||
Night | |||||
WEDNESDAY | Morning | Copy Tues to Wed No Yes | |||
Day | |||||
Evening | |||||
Night | |||||
THURSDAY | Morning | Copy Wed to Thurs No Yes | |||
Day | |||||
Evening | |||||
Night | |||||
FRIDAY | Morning | Copy Thurs to Fri No Yes | |||
Day | |||||
Evening | |||||
Night | |||||
SATURDAY | Morning | Copy Fri to Sat No Yes | |||
Day | |||||
Evening | |||||
Night | |||||
SUNDAY | Morning | Copy Sat to Sun No Yes | |||
Day | |||||
Evening | |||||
Night |
Download Manual
Daikin D4272 Digital Thermostat
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…