Comfortheat MCD5 ELECTRIC Programmable Thermostat Operating Manual

Comfortheat MCD5 ELECTRIC Programmable Thermostat

MCD5 Operations Manual – Electric

A Comfort Heat floor heating system has been installed in your floor. Floor heating warms from the ground up giving you an unparalleled feeling of comfort. This heating system is controlled by an electronic thermostat and floor sensor for optimum temperature control.

PRIOR TO TURNING ON
The sub-floor slab or screed must be fully cured before turning the heating on. Wait at least 3 weeks before turning it on and increase the floor temperature gradually over 2-3 days.

PRODUCT WARRANTY
TILE CABLE – 10 years
SLAB CABLE – 10 years
CARPET MATS – 5 years
TIMBER MATS – 5 years THERMOSTAT & SENSOR – 2 years

SUGGESTED TEMPERATURE SETTINGS
BATHROOM – 24 ~ 28ºC
LARGE TILED AREA – 21 ~ 22ºC CARPET – 19 ~ 21ºC
TIMBER – 24ºC
SLAB – 21ºC

The MICROTEMP RANGE of electronic thermostats is specifically designed for underfloor heating systems. The thermostats are vertically flush mounted and have a 2-pole isolator with a 16A output relay.
MCD5 – The MCD5 touchscreen thermostat has a built-in programmable time clock to automatically turn the floor heating system ON and OFF at selected times. During the OFF periods, the floor does not turn OFF but programs the floor temperature to your selected ‘set back temperature’. The floor is heating when the temperature display turns red.

TECHNICAL DATA – MCD5

• Supply Voltage: 240V AC, 50/60hz
• Output Relay: 16A SPST, 3600W max
• Switching Differential: 0.4 deg C
• Built-in Switch: 2 pole 16A
• Temperature Range: 0/+50 degC
• Clock Function: Up to 7 different 4 or 6 event
• program combinations
• Display: 220 x 176 pixel TFT – color touch
• Housing/protection: IP21
• Dimensions (HxWxD): H 114mm x W84mm x D40mm
• Mounted: Vertical or Horizontal

Factory Default settings: weekdays (days 1-5):

• on at 6 am – 25°C
  • off (set back) at 8 am – 20°C on at 4 pm – 25°C
  • off (set back) at 10.30 pm – 20°C
• weekends (days 6-7):
  • on at 8 am – 25°C
  • off (set back) at 11 pm – 20°C

note: thermostat does not “turn off” but changes to a “set back” temperature. This setback temperature can be changed.

TURNING ON FOR THE FIRST TIME [Factory Reset]

• Press the ‘MENU’ button
• Press the ‘Arrow’ button until you see ‘Engineer Settings‘ > Press OK
• Press the ‘Arrow’ button until you see ‘Factory Reset‘ > Press OK
• Press the ‘Arrow’ button until you see ‘RESET‘ > Press OK

The thermostat will turn off and on. Set language>OK Set time>OK Set date>OK The thermostat is now set to ‘factory default’ settings and is fully operational in auto mode. Default settings can be changed as detailed below.

PROGRAMMING This setback temperature can be changed.

• Press the ‘MENU’ button
• press the ‘Arrow’ button until you see ‘User Settings‘ > Press OK
• press the ‘Arrow’ button until you see ‘4-Event Schedule‘ > Press OK
• Select from either 5:2 6:1 or 7:0 > Press OK > Press Exit
• Press the ‘MENU’ button
• Press the ‘Arrow’ button until you see ‘4-Event Schedule‘ > Press OK
• Set day(s) of the week> Press OK
• Set Morning > Press OK
• Press the ‘Arrow’ button to set Morning ‘ON’ time > Press OK
• Press the ‘Arrow’ button to set Morning ‘ON’ temperature > Press OK
• Set Daytime > Press OK
• Press the ‘Arrow’ button to set Daytime ‘OFF’ time > Press OK
• Press the ‘Arrow’ button to set the Daytime ‘OFF’ temperature > Press OK (normal setting is 20°C – do not set to 0°C)
• Set evening > Press OK
• Press the ‘Arrow’ button to set Evening ‘ON’ time > Press OK
• Press the ‘Arrow’ button to set the Evening ‘ON’ temperature > Press OK
• Set Night > Press OK
• Press the ‘Arrow’ button to set Night ‘OFF’ time > Press OK
• Press the ‘Arrow’ button to set Night ‘OFF’ temperature > Press OK (normal setting is 20°C – do not set to 0°C)
• Repeat the process depending on your weekly configuration

MANUAL MODE SETUP
Override of the auto on /off programmed setting.

• Press the ‘MANUAL’ button
• Set temperature> Press OK – Hand will appear with set temperature
• To change the thermostat back to automatic mode – press the ‘AUTO’ button

COMFORT MODE
Comfort mode will temporarily override auto settings for a single length of time. Once the time expires the thermostat will revert to the auto-programmed setting.

• Press the ‘COMFORT’ button
• Set temperature > Press OK
• Set length of time > Press OK

Understanding Adaptive Function? ** IMPORTANT FOR IN-SLAB INSTALLATIONS **
The adaptive function allows the thermostats to predict when the floor heating should be turned on. A thermostat set to 28°C at 6 am will begin to turn on hours before (based on the last few day’s temperatures) in an attempt to be at 28°C at 6 am

Time of use meter
The Smart Power Meter varies the power tariff rate at different times of the day. Overnight the rate is at the ‘Off Peak’ rate and during the afternoon and evenings there is the ‘Peak’ rate. At the times between these, there are ‘Shoulder’ rates. The exact times of these rates should be confirmed by your power provider. As the cost of electricity during ‘Peak’ times is more expensive than during the ‘Off Peak’ or ‘Shoulder’ times the adaptive function on the MCD4 thermostat should be programmed to ‘OFF’.

Benefits of Adaptive Function (noninsulin installations)
As the weather becomes cooler, your thermostat will predict what time to turn on your system so your floors will always be warm and at your set temperature, as programmed.
Set the Adaptive Function to ‘Off’ (default setting for MCD5 is ‘ON’)

• Press the MENU button
• Press the ‘Arrow’ button until you see ‘Engineer Settings‘ > Press OK
• Press the ‘Arrow’ button until you see ‘Adaptive Function‘ > Press OK
• Press the ‘Arrow’ button until you see ‘OFF‘ > Press OK

Reference:

DOWNLOAD MANUALS:

Comfortheat MCD5 ELECTRIC Programmable Thermostat Operating Manual

OTHER MANUALS:

Comfortheat MCD5 Hydronic Programmable Thermostat Setup Manual

Comfortheat MCD5 Programmable Thermostat User Manual

Comfortheat MCD5 THERMOSTAT Wiring Diagram

Comfortheat MCD5 ELECTRIC Programmable Thermostat Operating Manual