Breeze33 BZ33-201P Programmable Thermostat Installational Manual

Breeze33 BZ33-201P Programmable Thermostat

Wall locations

The thermostat should be installed approximately 4 to 5 feet above the Iha floor. Select an area with average temperature and good air circulation.

Do Not Install a Thermostat In the Location

• Close to hot or cold air ducts
• That are in direct sunlight
• With an outside wall behind the thermostat
• In areas that do not require conditioning
• Where there are dead spots or drafts On comers or behind doors)
• Where there might be concealed chimneys or pipes

Subbase Installation

Wiring

• Tum Off Powar lo Heating/Cooling System

• Remove Old Thermostat
• Label Wires with Tags
• Separate Wallplate from N-Thannostat
• Separate Wallplate from New Thermostat
• Connect Wires Simply match wire labels. If labels do net match the latter& on the thermostat, check “AJIBmate Wiring (Conventional  Systems on page 9 and connect to terminal ea shown (-nDIH, below).

• Alternate Wiring (Conventional Systems) If labels do not match letters on the thermostat, check the chart below and connect to terminal as shown here (See notes, below

Caution: Electrical Hazard Failure to disconnect the power before beginning to install this the product can cause electrical shock or equipment damage

Terminal Designations

Installation Tip:
Do not overtighten terminal block screws, as this can damage the terminal block. A damaged terminal block can keep the thermostat from fitting on the subbase correctly or cause system operation issues. Max Torque = Sin-lbs.

DIAGRAM

Thermostat Operation

• LCD Display
• Fan Switch
• System Switch
• Temperature Setpoint Buttons
• User Buttons

LCD Display
See page 15 for details about this aisplay read out.

Fan Switch
Select ON or AUTO. ON will run the fan continuously. AUTO will cycle the fan on only when the heating or cooling system is on.

System Switch
Selects the operation mode on your HVAC system. Selecting HEAT turns on the heat mode. Selecting COOL turns on the coolmode. Selecting OFF turns both heating and cooling off. Selecting EMH (for heat pumps with auxiliary heat) will lockout the compressor and control emergency/ auxiliary heat.

Temperature Setpoint Buttons
Press the + or – buttons to select the desired room temperature.

User Buttons
Use these buttons to set up your programming options. Refer to the next page for detail.

Thermostat Quick Reference

Battery Door Information

Temporary and Permanent Hold Feature (if using programming)

Temporary Hold: The thermostat will display HOLD and + or ~ key. If you do nothing, the temperature will remain at this setpomt temporarily until next time period. Your program setpoint will then replace your temporary setpoint.

Permanent Hold: If you press the HOLD key at the left of your screen, you will see HOLD appear below the setpoint temperature in the display. The thermostat will now permane~ stay at this setpoint and can be adjusted using the keys.

To return to the program: Press the RUN SCHED key at the left of your screen to exit either temporary or permanent hold .

Filter Change Reminder
If your HVAC contractor has configured the thermostat to remind you when the air filter needs to be changed, you will see FILTER in the display when your air filter needs to be changed. Resetting the filter change reminder:When FILTER reminder is displayed;-you should change your air filter and reset the reminder by holding down the secona button from the top left side of the thermostat for 3 seconds

Programming The Thermostat

SetTime

1. Press the MENU button
2. Press SET TIME
3. Dayoftheweekwill be flashing. Use the 9 key to select the current day of the week.
4. Press NEXT STEP
5. The current hour is flashing. Use the key to select the current hour.
6. When using  12-hour time, make sure the correct a.m. or p.m. choice 1s selected.
7. Press NEXT STEP
8. Minutes are now flashing. Use the key to select current minutes.
9. Press DONE when completed .

Set Program Schedule 5+1+1 or 7Day

To customize your program schedule, follow these steps:

• Select HEAT or COOL with the system switch.

Note: You have to program heat and cool each seperately.

• Press the MENU button (If menu does not appear first press RUN SCHED)
• Press SET SCH ED. Note: Monday-Friday or (Monday if in 7 Days) is displayed and the WAKE icon is shown. You are now programming the wake time period for that day.
• Time is flashing. Use the key to make your time selection for tfiat day’s WAKE time period.
• Press NEXT STEP
• The setpoint temperature is flashing. Use the key to make your setpoint selection for that day’s WAKE time period.
• Press NEXT STEP
• Repeat steps 4 thru 7 for that day’s LEAVE time period, RETURN time period, and SLEEP time period. Continued on the next page

Set Program Schedule 5+1+1 or 7Day

Saturday:
Repeat steps 4 through 7 for the Saturday WAKE time period, LEAVE time period, RETURN time period, and for the Saturday SLEEP time period.

Sunday:
Repeat steps 4 through 7 for the Sunday WAKE time period, LEAVE time period, RETURN time period, and for the Sunday SLEEP time period

Technician Setup Menu

• Press MENU button.
• Press and hold TECH SET button for 3 seconds.
• Configure the installer options as desired using the table below.
• Use the + OR – keys to change settings and the NEXT STEP or PREV
• STEP key to move from one option to another.

Terminal Designations

• W2 ——— Auxiliary heat relay
• Y —Compressor relay
• G —Fan relay
• 0 —- Heat pump changeover valve energized in cooling
• R —-Transformer power
• C —Common wire from system transformer
• B —- Heat pump changeover valve energized in heating
• W/E——— Emergency heat relay

WARRANTY

Breeze33 Products LLC (Breeze33) warrants to the ORIGINAL PURCHASERthat its thermostats shall be free from defects in material and workmanship under normal use and service for a five (5) years. This warranty cannot be transferred – it is extended only to the original Purchaser or First User of theProduct. By accepting and keeping this Product you agree to all of the warranty terms and limitations of liability described below. Breeze33ʼs obligations under the warranty set forth above shall be to replace any Breeze33 Thermostat which is defective.

WHAT IS NOT COVERED?
The warranty above does not cover and Breeze33 is not liable for, (i) installation, (ii) any labor charges or (iii) products which have been damaged as a result of any accident, misuse, abuse, neglect, improper installation or maintenance, the use of abrasive or organic solvent cleaners, modification, failure to use the register, grille, or diffuser in accordance with instructions provided by Breeze33.

HOW TO OBTAIN WARRANTY SERVICE
Contact our warranty department at 740-314-4404 to report the defect. Return failed product with proof of purchase,your name, and address within 30 days of failure to:

• Breeze33 Products LLC 350
• Courtney Road Sebring,
• Ohio 44672 USA

LIMITATION OF LIABILITY
Breeze33ʼs liability on any claim of any kind, including, without limitation, warranty, negligence and/or breach of contract, shall in no case exceed the purchase price paid by the Customer. IN NO EVENT SHALL BREEZE33 BE LIABLE FOR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING, WITHOUT LIMITATION, DAMAGE TO PROPERTY) OR PUNITIVE DAMAGES, DAMAGES IN THE NATURE OF PENALTIES OR SIMILAR OR RELATED DAMAGES OF ANY KIND.

DISCLAIMER OF WARRANTIES
BREEZE33 EXPRESSLY DISCLAIMS ALL WARRANTIES, EXCEPT AS EXPLICITLY STATED HEREIN, TO THE FULLEST EXTENT PERMITTED BY LAW, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF PERFORMANCE, MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT. THIS DISCLAIMER INCLUDES ANY ORAL WARRANTIES OR REPRESENTATIONS MADE OR IMPLIED BY ANY AGENT, EMPLOYEE, SUBCONTRACTOR, MANAGER, DIRECTOR AND/OR REPRESENTATIVE OF BREEZE33.

REFERENCE:

DOWNLOAD MANUALS:

Breeze33 BZ33-201P Programmable Thermostat Installational Manual

Breeze33 BZ33-201P Programmable Thermostat Installational Manual