Thermostat and Display
User options allow you to customize some of your thermostat’s features. Most users will not need to make any changes to the settings in this section. To enter the User Options menu, press and hold the RETURN button for approximately 3 seconds until the screen changes and displays the first User Option.
Press the SpeedBar® up or down to change the setting for the displayed User Option. After you have changed your desired setting, press NEXT to advance to the next User Option. You may also press BACK to move backwards through the User Options.
When your changes are complete, press RETURN to exit.
Table of User Options
NOTE: A detailed description of each User Option follows this table.
| No. | User Options | Factory Default | Setting Options | Comments | Pg. |
| 1 | Filter Service Monitor | OFF | OFF | Disables filter service monitor feature. | 8 |
| 30, 60, 90, 120, 180, 365 | Selects a number of days that must pass before the thermostat will flash a Service Filter reminder in the display screen. | ||||
| 2 | UV Light Service Monitor | OFF | OFF | Disables UV service monitor feature. | 8 |
| 180, 365 | Selects a number of days before the thermostat will flash a Service UV reminder in the display screen. | ||||
| 3 | Humidifier Pad Service Monitor | OFF | OFF | Disables pad service monitor feature. | 8 |
| 180, 365 | Selects a number of days before the thermostat will flash a Service Humid reminder in the display screen. | ||||
| 4 | Set Point Adjustment Limit* | 0 ADJ | 0, 1, 2, or 3 ADJ 0 | Selects a temperature adjustment limit of 0 (disabled), 1˚, 2˚ or 3˚. | 8 |
| 5 | Thermostat Lock Code | 000 | 0-9 | Select a 3 digit lock code of 0-9 for each digit. | 9 |
* For this option to be available, thermostat must be set to security level 1 (See Installer Manual).
User Options 1, 2 and 3
There are three user selectable service monitors that will display reminders for a required air filter, UV bulb or humidifier pad replacement. The SERVICE segment flashes in the display along with FILTER, UV or HUMID. When the service interval has been reached, and required cleaning or replacement has been performed, press the RETURN button to reset the timer. Select OFF or a set number of days before the reminder will appear.
User Option 4
The Set Point Adjustment Limit will limit how much the temperature can be adjusted from the current set point when the thermostat is locked with security level 1(See Installer Manual). This setting will not allow the user to override the temperature past the selected limit amount of 1, 2 or 3 degrees from the current set point. When the user reaches the adjustment limit the screen will flash ADJ. A setting of 0 disables the adjustment limit.
Thermostat Lock Code
User Option 5
The Thermostat Lock Code sets a 3-digit code that you may use at any time to lock or unlock the thermostat. Setting the code in the user options mode does not activate the lock feature (See Locking/Unlocking Thermostat, page 15). You may choose a 3-digit code with each digit being 0-9.
The System Control has 5 modes of operation – AUTO, COOL, OFF, HEAT and EMER. The mode can be selected by pressing the SYSTEM button to scroll through the different modes.
NOTE: Depending on how your thermostat was configured, some system modes may not be available.
The Fan Control has 3 modes of operation – AUTO, ON and CIRC. The mode can be selected by pressing the FAN button to scroll through the different modes.
NOTE: Depending on how your thermostat was configured, some fan modes may not be available.
Temperature Adjustment – Press the SpeedBar® up or down to adjust the current set temperature.
Status Indicators
Status indicators appear in the display to let you know if your system is heating, cooling or off.
This thermostat provides you with a reset button that will erase all of your user settings. The reset feature does not affect the Installer Settings.
To reset the thermostat, use a small object such as a tooth pick or paperclip and gently press the button located inside the small hole on the front of the thermostat housing labeled “reset”.
NOTE: You cannot reset the thermostat if it is locked.
Auto Changeover Mode
Auto Changeover mode is a feature enabled/disabled in the Installer Settings (see Installer Manual). If enabled, it is selected by pressing the SYSTEM button until AUTO HEAT or AUTO COOL appears in the display. When Auto Changeover mode is enabled and selected, the system automatically switches between heating and cooling when the room temperature meets the programmed heating or cooling set points. To operate properly, the thermostat requires a “dead band” setting to eliminate program conflicts. The dead band is set in the Installer Settings (See Installer Manual). The default setting is 3° F. Therefore, you will not be able to set your heat or cool temperature within 3° F of each other. If a setting is made in either heating or cooling which violates the dead band, the opposite mode will adjust up or down automatically to maintain the programmed dead band spacing.
Compressor protection is enabled/disabled in the Installer Settings (See Installer Manual). If enabled, this feature is automatically present in cooling and/or heating (heat pump only) modes. This thermostat includes an automatic compressor protection delay to avoid potential damage to your system from short cycling. This feature activates a short delay after turning off the system compressor. Additionally, for multi-stage heat pump systems, this thermostat provides cold weather compressor protection by locking out the compressor stage(s) of heating for a period of time after a power outage greater than 60 minutes. This cold weather compressor protection can be manually overridden at any time by changing the system mode to OFF momentarily, then back to HEAT.
Your 3-digit Lock Code is set in the “User Options” portion of this manual (See “Setting User Options”, page 7 and 9). Once the code is set, the thermostat can be locked or unlocked at any time by entering that code.
To lock or unlock the thermostat, press and hold the NEXT and RETURN buttons together for 5 seconds (Figure 1).
The screen will change, displaying 000 and LOCK will be flashing (Figure 2). Press the SpeedBar® up or down to enter the first digit of your lock code and then press NEXT to advance to the next digit. Repeat this process to enter the second and third digit of your lock code. After entering the third digit, press RETURN.
If you entered a valid code the thermostat will be locked or unlocked (depending on its previous state). When locked, the word LOCKED appears in the display (Figure 3). If an invalid code is entered the word NO will briefly appear, indicating that an incorrect code was entered (Figure 4).
The AC Power Monitor feature is enabled in the Installer Settings (See Installer Manual). If enabled, this feature will automatically be present. If your thermostat was hardwired (power provided from the system with batteries as a backup) then the AC Power Monitor feature will indicate when a loss of power to the thermostat has occurred by displaying NO POWR.
Indoor Remote Sensing
Indoor remote sensing is achieved by installing a Braeburn® remote indoor sensor and is configured in the Installer Settings (See Installer Manual). If a Braeburn indoor remote sensor was installed and properly configured in the Installer Settings, the thermostat will sense temperature at a remote location or at a combination of a remote location and the thermostat location.
Outdoor remote sensing is enabled by installing a Braeburn® remote outdoor sensor. No additional configuration is required.
If a Braeburn outdoor remote sensor was installed you may press the BACK and NEXT buttons at the same time to view the outdoor temperature.
Thermostat Cleaning
Never spray any liquid directly on the thermostat. Using a soft damp cloth wipe the outer body of the thermostat.
Never use any abrasive cleansers to clean your thermostat.
Changing the Batteries
This thermostat requires two (2) properly installed “AA” alkaline batteries to provide power for the thermostat if 24 volt AC power is not connected. (See Installer Manual). If batteries become low, a battery indicator will appear in the display. You should change your batteries immediately when you see the low battery signal by following these instructions.
When installed by a professional contractor, this product is backed by a 5 year limited warranty. Limitations apply. For limitations, terms and conditions, you may obtain a full copy of this warranty:
Braeburn Systems LLC 2215 Cornell Avenue • Montgomery, IL 60538
Technical Assistance: www.braeburnonline.com
Call us toll-free: 866-268-5599 (U.S.) 630-844-1968 (Outside the U.S.)
©2020 Braeburn Systems LLC • All Rights Reserved.
Download Manual: Braeburn 3020 Non-Programmable Thermostat User Manual
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…