Bosch

Bosch Room thermostat II Instruction Manual

Bosch Room thermostat

Product Description

The room thermostat II measures the temperature at a suitable location in the room and ensures a more stable and efficient temperature control. It is the perfect complement to your Bosch Smart Home radiator thermostats

Description of the symbols

  • Warning! Note about hazards
  • Note: Additional important information
  • Note about the installation video

Safety instructions

  • Read this user manual completely before installing or commissioning the device and pay particular attention to the hazard information.
  • Do not charge used batteries, and do not attempt to reactivate them using heat or other means. Do not short-circuit batteries. Do not expose batteries to strong sunlight. Do not throw batteries into fire! There i is a risk of explosion!
  • Make sure the polarity is correct when inserting the batteries! Only use batteries of the same type. Drained batteries must be removed from the device immediately. Remove batteries from the device if it is not in use for a long period of time. Increased risk of leakage!
  • Store small cells and batteries which could be swallowed out of the reach of children. Swallowing can result in burns, perforation of the soft tissue and death. Severe burns can occur within 2 hours after swallowing. In the event that a cell or battery is swallowed, seek medical assistance immediately.
  • The device is not a toy! Do not allow children to play with it. Never leave the packaging material lying around unattended. Plastic film and small parts may pose a danger to children.
  • This device may be used by children from 8 years of age and by persons with reduced physical, sensory or mental capacities, or a lack of experience and knowledge provided these persons are supervised or have been instructed in the safe use of the device, and understand the corresponding risks.
  • When remotely or automatically controlling a device, it is not always possible to guarantee that commands are actually executed or that the correct device status is displayed in the app and on other Smart Home display devices because of external circumstances. This may lead to material damage and/or personal injury. Therefore, you must ensure to the greatest extent possible that no person is endangered at the time of remote operation or automated control. Please take special care when setting up or adjusting the remote control or when using the automated control and check the desired functionality at regular intervals.
  • Do not open up the device. It does not contain any parts to be maintained by the user. If a fault occurs, have the device checked by a specialist.
  • We accept no liability for material damage or personal injury which is caused by improper use or failure to observe the safety instructions. In these cases, any guarantee claim becomes void! We accept no liability for consequential damage.
  • For safety and approval reasons (CE/UKCA), the device may not be modified and/or no changes may be made to the device without authorisation.
  • Do not paint over the device! Do not apply wallpaper over the device!
  • Any use other than that which is described in the user manual is considered improper and leads to the exclusion of guarantee and liability.
  • Do not use the device if it has damage visible from the outside, for example, to the housing, control elements or connection sockets, or if it has a malfunction. If in doubt, please contact our service team.
  • Only operate the device indoors and do not expose it to moisture, vibrations, constant sunlight or other sources of heat, extreme cold temperatures and mechanical stress.
  • Only use the device together with original components and recommended products from Bosch partners.

Notes

  • The range within buildings can differ significantly from the range in open spaces. In addition to the transmitting power and the receiving properties of the receiver, environmental factors such as humidity, as well as the local structural situation, play an important role.
  • The device is only intended for use in residential environments.
  • The device is only intended for private use. You can also use the explanatory videos and additional information on our website as an additional aid for mounting, installing, starting up and restoring the factory settings on your Bosch Smart Home room thermostat II: www.bosch-smarthome.com/rom/room-thermostat-2

Product Overview

Item Name Explanation
1 Device front view
2 LED display
3 Status LED
4 Rotary knob/system

button

5 Device rear view
6 Sensor connection Connection for op-

tional accessories.

7

Mounting bracket receiving openings For different angles of inclination of the

device.

8

Battery compart- ment Ensure correct po- larity when inserting

the batteries!

9 Mounting plate Used to attach the

device to the wall.

10

Mounting bracket Used to install the device on even

surfaces.

LED display (2)

Item Name Description
a Information area Displays error codes or other additional informa-

tion.

b Humidity Displays room humidity in normal operation.
c Status indicators
Battery status Appears with low battery charge
Connection status Wireless connection to the controller is active. In the event of constant flashing, there is a connection

problem with the controller.

Child lock Press the system button >3 seconds, adjust the

desired value by turning

Open window The system has detected an open window in the

room. Heating/cooling mode paused.

d Cooling mode The device/system is set to cooling mode.
e Heating mode The device/system is set to heating mode.
f Room control modes

(press system button 1x, select mode)

Automatic Room control is controlled via a schedule.
Manual Temperature at constant value. Can be changed via

rotary knob.

Heating break The regulation in the room pauses.
g Value display Displays actual and set temperature. Other text information in case of an error or during configura-

tion.

The status LED (3) shows the status of the room thermostat using flashing codes

Signal Meaning Measures
Flashes orange Pairing mode (is active) or device is communicat- ing with the

controller

Please wait
Flashes green Pairing mode (successful) or process

confirmed

Flashes red 1x Pairing mode (not successful) or

process failed

If this is the first tun- ing attempt, please try again. Otherwise reset the device to the factory settings and contact the service department if

necessary.

Flashes red every 15 sec- onds Functional error Look for informa- tion in the Smart Home app. Contact the service team if

necessary.

Start-up
Ensure that you have a Bosch Smart Home controller and the Bosch Smart Home app and have successfully configured both. Now start the Bosch Smart Home app and select “Add new device”. Follow the instructions in the app.

Resetting to factory settings
You can reset the device to its factory settings as follows:

Open the battery compartment (8) and remove one of the batteries. Replace the battery while holding the rotary knob (4) pressed. Hold the knob pressed until the status LED (3) on the room thermostat flashes orange and “RES” appears on the display. Now release it briefly and press the knob again and hold until the LED lights green. The device then restarts. Please note that it can take a few seconds until the room thermostat is ready for operation again.

  • When resetting to factory settings, the settings and information are only lost from the device and not from the Bosch Smart Home controller.
  • To re-configure the device, first delete it in the device management section of the Bosch Smart
  • Home app and then add it again in the usual configuring process

Maintenance and cleaning

Removing o or changing the battery
To remove or replace the batteries, remove the device from the mounting plate (9) or first remove the mounting bracket (10). Open the battery compartment( 8). Remove the batteries. Take care to ensure the correct polarity when replacing them. The device does not require maintenance. Leave any repairs to a specialist. Clean the device with a soft, clean, dry and lint-free cloth. When cleaning, do not use any cleaning agents containing solvents

Simplified declaration of conformity

  • Robert Bosch Smart Home GmbH hereby declare that the radio equipment type Bosch Smart Home BTH-RM corresponds with the directive 2014/53/EU. The complete text of the EU declaration of conformity is available via the following web address: https://eu-doc.bosch.com
  • Robert Bosch Smart Home GmbH hereby declares that the radio system type BTH-RM complies with Regulation 2017. The full text of the declaration of conformity is available at the following internet address: https://gb-doc.bosch.com

Environmental protection and disposal
Electrical or electronic devices which are no longer usable must be collected separately and disposed of via an environmentally friendly recycling facility (European Directive on Waste Electrical and Electronic Equipment). Use your country’s specific return and collection systems when disposing of waste electrical or electronic devices. Used batteries do not go in the household waste! Dispose of them at your local battery collection point!

Technical data

Device type designation BTH-RM
Protection type IP21
Ambient temperature 0 – 50 °C
Max. humidity 80 % (non-condensing)
Dimensions (W × H × D) 86 × 87 × 28 mm
Weight (without batteries) 85 g
Radio protocol ZigBee 3.0
Radio frequency band 2.4 – 2.4835 GHz
Max. transmitting power 10 dBm
Radio range in the open < 100 m
Software class A
Receiver category 2
Batteries 4 × 1.5 V Micro/AAA/LR3, alkaline
Battery lifespan (typical) < 2 years

Spare parts /accessories
For information on available spare parts or accessories, please visit: https://www.bosch-smarthome.com/rom/spareparts

Service information

Reference

Download Manual:

Bosch Room thermostat II Instruction Manual

Bosch Room thermostat II Instruction Manual

wpx_thermostats

Recent Posts

Johnson Controls T7000e LCD Digital Thermostat Installation Guide

Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide

1 year ago

Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’S GUIDE

Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE

1 year ago

Hetta HS01RF WIRELESS THERMOSTAT KIT USER MANUAL

Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…

1 year ago

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat USER MANUAL

HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…

1 year ago

Honeywell RLV450 PROGRAMMABLE THERMOSTAT USER GUIDE

Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…

1 year ago

Honeywell RLV431 Programmable Thermostat User Guide

Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…

1 year ago