IMPORTANT:
Read carefully and follow these instructions as well as the general advice on safety and risks before installation. Keep this leaflet in a safe place for future reference. If you have any doubt about the safety of the unit seek the advice of an expert. If the unit is used in a greenhouse make sure that the electrical connections are carried out by qualified personnel.
General
After unpacking and before switching on, make sure that the unit and all its accessories are perfectly in order. If there has been any damage in transit, consult your dealer or the manufacturer immediately. Keep the packaging materials (polythene bag, polystyrene, nails etc.) out of reach of children because they represent a potential source of danger. This also applies to small parts supplied, which can be swallowed. This electronic thermostat can be used for a wide variety of temperature control applications, for example for heating and cooling greenhouses and winter gardens, or for monitoring water temperatures in aquariums, the air temperature in terrariums or the soil temperature in seed beds. It is simple to operate and can be connected to any type of heating cable, heating mat or other heating or cooling devices, provided that the maximum heating power of 3000 W is not exceeded. This thermostat is only licensed for connection to 230 V / 50-60 Hz a.c. voltage. The unit must be protected from high degrees of contamination and moisture. If it is used for any application other than that described above it may be damaged and risks such as short-circuiting, fire, electric shock etc. may ensue. The safety and installation instructions must be strictly adhered to.
Advice on safety and risks
Make sure that the mains voltage corresponds to the voltage indicated in Chapter 2 (technical data). The place of installation must be chosen so that the unit can under no circumstances get wet (e.g. dripping condensation, open roof hatches, etc.) or fall into water. The thermostat may be operated in a horizontal or vertical position.
Room temperature control
The sensor should be installed at half room height and should be freely suspended. The room temperature can only be optimally controlled when the sensor is not influenced by draughts, solar radiation or other heat or cold sources.
Cultivation of plants and seeds
Position the sensor in the soil close to the roots. The sensor must be entirely surrounded by soil. In large plant pots the sensor should be located in the middle of the pot.
Water temperature control
For water temperature control (e.g. in an aquarium), the sensor should be positioned in the central layers of water. Here too the sensor must be completely surrounded by water.
When installing, check that the unit or mains cable is not damaged. Also make sure that the sensor cable has not become sharply kinked as this may impair operation.
Switching on/off
As soon as the unit has been connected to the supply voltage it can be switched on by means of the “ON/OFF” button. To do this the button must be press for 3 seconds. Immediately after switching on the unit determines the ambient temperature of the sensor and indicates it on the display. To switch off, again press the “ON/OFF” button for 3 seconds.
It is indicated by the yellow LED whether the heat or cool mode is active
Cleaning
Disposal and repair
Servicing and maintenance under warranty
We give you a 2 year unlimited manufacturerʼs warranty (from date of purchase) on all Bio Green products. Excluded from the warranty is damage due to violence, improper use and failure to follow instructions for use, cleaning and maintenance work. The manufacturer accepts no liability for damage due to frost, insufficient heating power related to the room dimensions, or due to inadequate heat insulation.
Important note
The unit may only be opened and repair work may only be carried out by licensed specialists in accordance with the applicable repair regulations. Only original parts may be fitted. A guarantee of perfect operation and reliability can only be given if the unit is installed and handled expertly. This also applies to the provisions of the Technical Equipment Act and the applicable accident prevention regulations. In case of warranty please complete the warranty and info card attached for this purpose.
If you have any further questions refer to our Bio Green Service:
Bio Green
DOWNLOAD MANUALS:
BIOGREEN THERMO 2 Digital-Thermostat Installation and operating instruction
BIOGREEN THERMO 2 Digital-Thermostat Installation and operating instruction
Johnson Controls T7000e LCD Digital Thermostat Johnson Controls T7000e LCD Digital Thermostat Installation Guide
Honeywell T8635L Microelectronic Communicating Programmable Thermostat Honeywell T8635L Microelectronic Communicating Programmable Thermostat USER’s GUIDE
Hetta HS01RF WIRELESS THERMOSTAT Kit PAIRING INSTRUCTIONS Insert batteries into the Thermostat. Ensure that the…
HEAT-MAT NGT-567-0010 Underfloor Heating Thermostat Menu Introduction The NGT thermostat can switch your underfloor heating…
Honeywell RLV450 PROGRAMMABLE THERMOSTAT READ BEFORE INSTALLING DESCRIPTION * LP appears only for the first…
Honeywell RLV431 Programmable Thermostat Description The RLV431 thermostat can be used to control an electric…