SALUS VS35 Wired Digital Non-Programmable Thermostat Quick Guide

SALUS VS35 Wired digital Non-Programmable thermostat 

Terminals description

Terminal	Description
L,N	Power Supply 230 V AC
NSB	Night SetBack (input 230 V AC)
SL	Switched output (230 V AC)
S1, S2	External temperature sensor

Proper thermostat placement

Button Functions

LCD Icon description

1. Current active mode
2. Comfort mode
3. Standard mode
4. Economic mode
5. Automatic mode
6. Frost protection mode
7. Temperature unit
8. Manual mode / temp. override
9. Current / set temperature
10. Key lock
11. Settings
12. Additional temperature sensor
13. Cooling
14. Heating

Installation

The VS35 thermostat has been designed for flush mounting in a standard electrical box with a diameter of 60 mm.

Wiring diagrams

An additional temperatur Te sensor is optional.

VS35 thermostat in connection with wiring centre 
In this diagram, the VS30 thermostat manages the NSB function, more details about NSB function can be found on the next page.

Note: In the KL06 wiring centre, the SL terminal is marked with an arrow icon .
NSB function and an additional temperature sensor is optional.

VS35 thermostat in connection with actuator or pump

VS30 thermostat in connection with a boiler with a “NO” voltage free terminal through the RM-16A relay

Temperature setting

Press any button to highlight the screen, then follow the steps below:

Manual mode

temperature settings
There are 4 temperature levels available. In manual mode only one temperature level is active (icon in the frame indicates which mode is currently choosen). For each temperature levels you can set a different temperature.

• Comfort mode
• Standard mode
• Economic mode
• Frost protection mode. Usually used in a longer period of absence or during the holidays (available only in heating mode).

Press any button to highlight the screen, then follow the steps below:

NSB function – automatic mode
The NSB (Night SetBack) function can automatically change temperatures on VS35 daily thermostats via VS30 programmable thermostat connected to a wiring centre (or another external clock). NSB function switches between comfortable temperatureand economic temperature.
To activate the automatic mode, select the icon A. On display together with the A icon, the controller indicates active temperature mode: or .

Press any button to highlight the screen, then follow the steps below:

Note: For the NSB function to work, it is necessary to connect the wirings properly. Connection diagrams can be found on the previous page.

Changing the HEATING / COOLING mode

Press any button to highlight the screen, then follow the steps below:

Note: Heating / cooling mode can also be set using the service parameter d18.

Offset function (temperature calibration)

The VS35 thermostat allows you to adjust the displayed temperature ± 3.0°C. You can do it according to the following steps:
Press any button to highlight the screen, then follow the steps below:

Note: You can also set the Offset temperature value using the service parameter d02.

Installer settings

Press any button to highlight the screen, then follow the steps below:

Note: To restore the thermostat’s factory settings, in step 2 set the PSuu to 47 code, and confirm the selection with the button.

dxx	Function	Value	Description	Default value
d01	Control method temperature	0	PWM algorithm	0
		1	Span ±0.25°C
		2	Span ±0.5°C
d02	Offset temperature	from -3.0°C to +3.0°C	If the thermostat indica- tes wrong temperature, you can correct it by ± 3.0°C	0°C
d03	Using a floor temperature sensor (S1, S2)	0	No sensor	0
		1	Sensor is connected
d04	External sensor used for air or floor temperature measurement (Function is active, when d03=1)	0	Thermostat measures the temperature only on the external sensor	0
		1	The sensor is used as a protection against overheating the floor
d05	Cooling mode control method	1	Span ±0.5°C	2
		2	Span ±1.0°C
d06	Type of thermoelectric actuator	0	NO – normally open	1
		1	NC – normally closed
d07	Valve protection	0	OFF	1
		1	ON
d08	Frost protection temperature	5-17°C	Frost protection / Holiday mode temperature	5°C
d12	Heating temperature limit	5-35°C	The maximum heating temperature that can be set by the user	35°C
d13	Cooling temperature limit	5-40°C	The minimum cooling temperature that can be set by the user	5°C
d14	Maximum floor temperature (this function is active  in heating mode when d04 = 1)	6-45°C	In order to protect the floor from overheating, heating will be turned OFF, when the maximum temperature of the floor sensor will be reached	27°C
d15	Minimum floor temperature (this function is active  in heating mode when d04 = 1)	6-45°C	In order to protect the floor, heating will be turned ON, when the minimum temperature of the floor sensor will be reached	10°C
d16	Lower floor temperature limit for cooling (this function is active  when d04 = 1)	6-45°C	In order to protect the floor, cooling will be turned OFF, when the minimum temperatu- re will be reached	6°C
d18	Operating mode HEATING / COOLING	0	Heating system	0
		1	Cooling system

Error codes

Error code	Description
Err02	The maximum/minimum floor temperature has been exceeded
Err03	The temperature sensor is faulty
Err04	The temperature sensor is shorted

Reference

Download Manual

SALUS VS35 Wired Digital Non-Programmable Thermostat Quick Guide

OTHER MANUALS

SALUS VS35 Wired digital Non-Programmable Thermostat User Manual

SALUS VS35 Wired digital Non-Programmable thermostat Wiring Daigram

SALUS VS35 Wired digital Non-Programmable thermostat Quick Guide