SALUS RT510SPE Wireless Programmable Thermostat Quick Guide

Salus-logo

SALUS RT510SPE Wireless Programmable Thermostat 

SALUS-RT510SPE-Wireless-Programmable-Thermostat-PRODUCT

Introduction

The RT510SPE module will switch your appliance on or off in accordance with the temperature set by you. The completed RT510SPE series consists of a transmitter – RT510TX thermostat and a Smart Plug SPE868.
Go to www.salus-manuals.com for the full PDF version of the manual.
Product Compliance
This product complies with EMC 2014/30/EU, LVD 2014/35/EU, RED 2014/53/EU, and RoHS 2011/65/EU. Full text of the EU Declaration of Conformity on www.saluslegal.com
868.0-868.6MHz; <13dBm www.saluslegal.com
Safety Information
Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel.

Button Functions

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.1

  1. Press for frost mode
  2. Press 3 sec for holiday mode
  3. Increase button
  4. Decrease button
  5. Press to confirm the setting
  6. Press to select setting
  7. Press to enter/exit the permanent override
  8. Press to enter/exit boost mode

LCD icons

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.2

  1. Current day of the program
  2. Current time
  3. Current Temperature
  4. Temperature unit
  5. Frost Protection
  6. Vacation Mode
  7. Temporary/Permanent Override
  8. Heating Mode ON
  9. RF signal
  10. Low battery
  11. Boost Mode
  12. Program number

DIP switch settings

The DIP Switches can be found on the rear of your thermostat

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.3

Control feature TPI Span
Operation When TPI is selected on DIP switch № 2, the DIP switch № 1 is functional. You can choose the Cycles Per Hour between a lower comfort level (6CPH) and a higher comfort level (9CPH). When Span is selected on DIP switch № 2, the DIP switch № 1 is not functional. The temperature accuracy of your thermostat is set to ± 0.25 °C.

Smart plug LED indicationSALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.4

If the thermostat loses connection with the Smart Plug, the Smart Plug goes into fail safe mode after 22 minutes. In this mode you still can operate your Smart Plug manually (by pressing the button on the device).

Installation

  1. Step 1
    The thermostat and the smart plug are pre-paired from the factory if purchased as a pack. If not, follow the thermostat pairing process.SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.5
  2. Step 2SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.6

Thermostat pairing process

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.7

  1. In case you have more than 1 smart plug, set ALL the smart plugs into pairing mode and start the pairing process. The LED will flash red when the plug is in pairing mode.
  2. Put the thermostat into pairing mode, by pressing the pair button for 3 seconds. After the smart plug is paired with the thermostat, the LED is steadily red.
  3. Begin pairing processSALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.8
  4. End pairing processSALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.9

Test the pairing process

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.10

Setting hours and day

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.11

Continue with the same steps for setting the Day. Press Set to return to the Main Screen.

Temporary override

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.12

Permanent override

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.13

Setting programs

  • You can create personalized programs for your controller. You have the option to choose between a 5-2 days program or a daily one by using parameter d04 from Installer mode.
  • Press SET to change your programsSALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.14
  • Use and to select Weekend/Weekday, pressSALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.15 to confirm your option. Follow the same steps for setting the hour, minutes and temperature. After you have done all the changes, please press SET to confirm all your choices and to return to the Main Screen.

Installer mode

SALUS-RT510SPE-Wireless-Programmable-Thermostat-FIG.16

Press the three buttons together for 3 seconds. Use +HR to select dxx parameter, or to change the parameter value and to confirm.

PARAMETER

dxx Function Parameter Default value
d01 Temperature display increments 0.1 or 0.5°C 0.5°C
d02 Temperature offset +/-3.0°C 0.0°C
d03 Frost setpoint 5.0-17.0°C 5.0°C
d04 Programmer selection 5/2 or 24 hr (7d) 52d

SALUS CONTROLS DISTRIBUTOR:
QL CONTROLS Sp. z o.o., Sp. k.
ul. Rolna 4,
43-262 Kobielice,
Poland

Importer:
SALUS Controls Plc
Units 8-10 Northfield Business Park Forge Way, Parkgate
Rotherham
S60 1SD
United Kingdom
www.salus-controls.eu
SALUS Controls is a member of the Computime Group.
In accordance with the product development policy, SALUS Controls plc reserves the right to change specifications, design, and materials used in production, presented in this manual, without prior notice.

REFERENCE

Download Manual

SALUS RT510SPE Wireless Programmable thermostat Quick Guide

OTHER MANUALS

SALUS RT510SPE Wireless Programmable thermostat Wiring Diagram

Salus-logo

SALUS RT510SPE Wireless Programmable Thermostat Quick Guide

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *