SALUS EP110 Single Channel Programmable Thermostat Quick Guide

SALUS EP110 Single Channel Programmable Thermostat 

INTRODUCTION

Programmable timers EP110, EP210, and EP310 are used to switch ON/OFF the heating system, the hot water or any electronic device like pumps or lights as needed. It works by controlling with programmed schedules (24H or 5-2 schedule types) which contain 3-time programs each.

PRODUCT COMPLIANCE

EU Directives: 2014/30/EU, 2014/35/EU and 2011/65/EU.
Please check www.saluslegal.com for the full information.

SAFETY INFORMATION

Use in accordance with the regulations. Indoor use only. Keep your equipment completely dry. Disconnect your equipment before cleaning it with a dry towel. The unit is to be used for the control of room temperature inside the house.

INSTALLATION

Use in accordance with the EU and national regulations. For indoor use only. Keep your device completely dry.
This product must be installed by a competent person and in accordance with all the EU and national regulations.

Technical data

	EP110	EP210	EP310
Power Supply	230 V AC	230 V AC	230 V AC
Max load	3 (1) A	3 (1) A	3 (1) A
Output	NO / COM / NC volt free	2 x SPDT 230V AC	3 x SPDT 230V AC
Number of channels	1	2	3
Dimensions [mm]	120 x 98 x 27	120 x 98 x 27	120 x 98 x 27

Buttons functions

Button	Function
MODE	Select operating mode (ON, ONCE, AUTO, ADV, OFF)
+HR	Activate/deactivate BOOST function
	Turn on the LCD backlight
	Press for 3 sec to activate HOLIDAY mode
	Increases the selected setting
	Decreases the selected setting
	Select a clock or program setting
	Sets a clock or programme setting
	Reset to Factory settings

LCD display icon description

1. Device operation (animated icon)
2. Number of hours for the BOOST function
3. ON/OFF indicator
4. Work mode
5. AM/PM
6. Holiday mode
7. Clock
8. The day of the week
9. Program number

1. 1. Zone I operation mode
2. Day of the week
3. Program number
4. ON/OFF indicator
5. Zone II operation mode
6. Zone II work status
7. AM/PM
8. Number of hours for the BOOST function for Zone II
9. Number of hours for the BOOST function for Zone I
10. Zone I work status
11. Clock
12. Holiday mode

1. Zone I operation mode
2. Zone II operation mode
3. Zone III operation mode
4. Program number
5. ON/OFF indicator
6. Holiday mode
7. AM/PM
8. Number of hours for the BOOST function for Zone III
9. Zone III work status
10. Zone I work status
11. Number of hours for the BOOST function for Zone II
12. Zone II work status
13. Number of hours for the BOOST function for Zone I
14. Clock
15. Day of the week

Jumpers settings

The parameters can be changed using the jumpers on the back of the device.

Note: Disconnect the power supply before working with the device.

Note: After changing the settings, it is necessary to reset the device using the button.

Wiring diagram

All wire connectors are located on the back of the device. To remove the cover, loose two screws located at the bottom of the device and then remove the back of the housing.

Note: Disconnect power supply before working with the device.

Setting time and date

Operation modes

There are 5 different work modes available. Using MODE button, you can change modes directly according to the following sequence:

1. ON mode
2. ONCE mode
3. AUTO mode
4. ADV mode
   The ADV mode can be activated if the ONCE or AUTO mode is selected when it is activated
5. OFF mode

Programming EP110 controller

You can create 3 independent time schedules. There are 2 work models to choose from:

• business days + weekends (5-2)
• each day separately (24 hours)
  The controller works by default in working days + weekend mode (5-2).
  To set each day separately (24 hours), change the jumper position according to the diagram on the previous page.

Programming EP210/EP310 controller

You can create 3 independent time schedules for each zone. There are 2 work models to choose from:

• business days + weekend (5-2)
• each day separately (24 hours)
  The controller works by default in working days + weekend mode (5-2).
  To set each day separately (24 hours), change the jumper position according to the diagram on the previous page

HOLIDAY mode

Holiday mode is used to disable all controller outputs for a specified number of days (up to 31 days).
When HOLIDAYS mode is active, aircraft icon will appear on the display.

BOOST Function

BOOST function extends the active program time to 1-9 hours. Press the +Hr button to activate BOOST mode (each press of the button extends the active program by 1 hour

Factory Settings

If you made a mistake, want to change controller parameters or return to its factory settings, you can reset the controller with button

SALUS Controls plc
SALUS House  Dodworth Business Park South, Whinby Road, Dodworth, Barnsley S75 3SP UK.
SALES: T: +44 (0) 1226 323961
E: [email protected]
TECHNICAL: T: +44 (0) 1226 323961
E: [email protected]
Issue Date: Feb 2014
Maintaining a policy of continued product development SALUS Controls plc reserves the right to change the specification, design, and materials of products listed in this brochure without prior notice. SALUS Controls is a member of the Computime Group 00089.

REFERENCE:

Download Manual:

SALUS EP110 Single channel programmable Thermostat Quick Guide

Other manuals:

SALUS EP110 Single Channel Programmable Thermostat Installation Manual

SALUS EP110 Single Channel Programmable Thermostat Quick Guide