Roma Heating TS700 – Programmable Touch Screen Thermostat Instructional Manual

Roma Heating TS700 – Programmable Touch Screen Thermostat

This TS700 Programmable touchscreen thermostat is designed to control electric underfloor heating Systems, electric heating devices, or on/off valve actuators used in water heating Systems. The TS700 can be fully programmed to automate your heating cycle to suit your lifestyle or can be used in a simple manual mode. With a built-in air sensor and external floor sensor the TS700 is a modern, stylish easy-to-operate thermostat with high functionality suitable for multiple uses.

Technical data

Volt age	AC23 0V so~6oHz
M ax Load	16Amps
Power consumption	2VA
Setti ng ran ge	5°C…80°C
Limitation range	5°C…60°C (factory setting:35°( )
Accuracy of temperature	o.s~10°CAdjust is able, factory setting±l °C
Ambient temperature	_ 5~50°C
Protective housing	IP20
Hou si ng material	An i-flammable PC

Power
Press the power key to turn the TS700 unit ON and OFF. Also used to accept and exit programs and advanced settings pages.

upand Down
Use the and” keys to increase and decrease the temperature, (please note the screen will revert to the original screen after 3 seconds Of inactivity when changing manual temperature) or to set values required in each individual program or setting.

Lock Screen
Hold the keys simultaneously for 10 seconds to lock the screen, (after 10 seconds symbol will appear at bottom Of the screen). TO unlock repeat this process for 10 seconds to unlock the screen.

Time and Day Setting
Hold the key for 10 seconds until the time, (minutes) starts flashing. Use the and keys to set the correct minutes. Once the minutes are correct press and the hours will start flashing. Again use theandkeys to set the correct hours/time. Once the hours and time are correct press the key again and the days will start flashing. Please note the days are represented by numbers 1 — 7. Monday = 1, Tuesday = 2, Wednesday = 3, etc, etc. Use the ” and keys to set the correct day Of the week. Press the key once more and the thermostat will revert to the home screen and the new time and day should be as per your settings.

Mode selection Key / automated program setup
When the unit is on press the key to change between “manual and “automatic modes. Each time key is pressed the unit will change between modes.

Display symbols

Programming: Event time and temperature

The below table shows the default settings for the TSL700 5/2 day mode.

(Note: When automating your heating you are not turning the thermostat or heating ‘on’ and ‘off’ during the day but simply changing the time and temperature 6 times during a 24-hour cycle. The thermostat will then automate the heating according to the set times and temperatures you have input to suit your lifestyle).

Program your TS700

There are 3 automated modes to select from, (see advanced settings ). These instructions explain how to set the default 5/2 day mode. The 5/2 option sets days 1-5, (Monday — Friday) all the same and days 6-7, (Saturday — Sunday) both the same. The same setting principles below should be used to set 6/1 and 7-day modes. To set up the automatic programming, hold the key for 10 seconds. Once the screen changes to show only the time and day numbers on the left-hand side, use theand to set the Event time. This time should be when you first want the heating to change temperature, (ie the time when you get up in the morning). Once the time is correct press and then again use theand keys set the Event 1 temperature you require at this time. You have now set Event 1 time and temperature set points in your daily Schedule. The thermostat will now hold this setting until you set the next time and temperature setting For Event 2 in the next stage.

Event 2. Press again and the symbol at the top of the screen will change to . Using the andkeys change the time to when you want the temperature to change again, (ie when you leave the house for work). Once the time is set press again using the and keys to change the temperature you require at this time. You have now completed Event 2.

Repeat the above process for ( ) the remaining events 3-6. Once you have set up events 1— 6 press and the weekend setting will appear for days 6-7, (Saturday and Sunday). Again set the time using ” A “and pressC12 Now set the temperature withand and pressYou will now see the event symbol has changed( Note: There are only two events on weekend setting, (ie temperature is turned up in the morningtfand down in the evening ( Complete the weekend time and temperature settings. By pressing again you can go back over your settings for each event to check over them and make any changes using and keys if required. Once you are happy with your settings confirm these settings and return to the main/home page.
(Note: For the thermostat to run your new settings the symbol must be highlighted. When on the home page, If is not showing press0nce and will appear).

 Advanced setting
To access the advanced settings menu you must first turn the unit Off by pressing the key. Once Off press and hold the and keys simultaneously. This will bring up: RdJ (menu 1). You can scroll through the 10 different menu settings by pressing the key use the and keys to make any changes required to each menu setting. Please see the table below for advanced setting menu information.

Menu	Symbol	Setti ng	Recommended Setting	Or
1	!RdJ	Temperat ure ca li brati on	unn. u	Adju st measured temperat ure
2	25EN	Sensor mode	Ou/::	IN: built-in ai r se nsor OUT: fl oor se nsor ALL: both ai r & flo or se nsors
Please Note: If Err error is displayed this indicates that floor sensor is not connected
3	3L/ F	t emperatu re Limit ati on	35.0	Adjust li mit ati on value, Limit ati on range:S0  ( ~90°c
4	Yd/ F	Swit ching diff erenti al	,,.un	Adjust swit ching diff erenti al
5	5Lr   P	Antifr eeze fun ction	OFF	Turn on/ off Anti -fro zen fun cti on
6	b Pr G	Set vacation mode	/, 2, 3 , L/ , 5, b , ‘7	2: 5/ 2 day mode 1: 6/ 1 day mode 0: 7 day mode
7	‘7 r LE	Potenti al-fr ee output	unun	00: in sa me way 01: For Wat er Heati ng
8	BdL’::I	Potenti al-fr ee output delay	un	Change th e delay ti me
9	“IHI F	M ax . Temperat ure	35.0	M ax. Limit ati on temperat ure se t point {8 0 °( ) on se nsor mode “a ll ” only (menu 2)
10	RFR[	Reset to facto ry se tti ngs	–	Pro gramming parameters will be reset to facto ry se tti ngs when sy mbol ” – ” appears (Hold Down ” /’:, ” key for 10 seconds)

Connecting Diagram

Note: cablæ has no polarity. The probe can be wired into their designated ports either way round

Dimension:(mm)

Fitting

1. Release the front cover by inserting a screwdriver into the bottom release slot and twist gently
2. Taking the backing plate off by sliding the metal locking band up
3. Insta backing plate on the electric ca l connection box with screws provided. (We recommend a 47mm deep back box, supplied by others).
4. Wire thermostat into feed, load, and sensor ca bl es and maneuver r unit firmly back against the backing plate.
5. Lock the thermostat back to the backing plate by sliding the metal locking back-down clamps.
6. Press Thermostat cover back over the screen by locating the top lugs first then pressing the bottom clips firmly back to close.

REFERENCE:

DOWNLOAD MANUALS:

Roma Heating TS700 – Programmable Touch Screen Thermostat Instructional Manual

Roma Heating TS700 – Programmable Touch Screen Thermostat Instructional Manual