ORBIS LOGO

Orbis THALOS ELECTRONIC TOUCH SCREEN THERMOSTATS  

Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS -PRO

User Manual

Wall mounting touch screen thermostat for temperature control both in heating and cooling. It performs actions of type 1B and is intended for operating in environments Pollution Degree 2 and Overvoltage Category III (EN60730-1). Thalos has a monochrome backlit display and an input where it is possible to connect an external contact suitable to reduce the setpoint of 3°C.

SAFETY WARNINGS
During product installation and operation it is necessary to observe the following instructions:

TECHNICAL SPECIFICATIONS

 Power supply:

 Terminals:

DIMENSIONS

Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 1

WIRING DIAGRAMSOrbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 2

LEGEND

Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 3

INSTALLATION

Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 21

OPERATION

During the standard operation the thermostat displays the detected temperature value and the relay status is identified by the symbolOrbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 4 (heating) or Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 5(cooling).

Setpoint modificationOrbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 6

Depleted batteries signal
Replace the batteries as soon as possible! Dispose of the batteries in the appropriate recycling containers.

Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 7

Switch offOrbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 8

Note: in heating mode (winter), if the Thalos is off, it regulates the antifreeze Toff temperature in order to prevent freezing of the system. Toff can have values from 1 to 10° C or be excluded; in this case any minimum temperature is guaranteed

Error messages

Occurs in case of probe failure.
In this case the Thalos activates the receiver for 10 minutes every 4 hours (if the antifreeze temperature Toff is active)

Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 9

Reset
Unhook and re-hook the thermostat from the base. Press the keys for at least 3 seconds during the flashing.Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 10.

Default valuesOrbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 11

Advanced programming

To enter menu Advanced programming keep simultaneously pressed for 5 seconds the keys and until PR will appear. The items of the menu are displayed in succession. For each item is displayed an identity breviation and its relative blinking value. Use the keys and to modify the blinking value. After 3 seconds without touching the keys there is the passage to the following parameter. The writing END will appear when all parameters are set and the thermostat returns successively in standard mode saving the effected modificationsOrbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 20

Orbis- THALOS- ELECTRONIC- TOUCH -SCREEN- THERMOSTATS - 13

Night reduction temperature
Thalos has got an input to whom to connect an external contact (see wiring diagrams). With closed contact, the setpoint is reduced by 3 °C than the set one.

Backlighting management
The display backlighting is normally OFF and it is enabled (blue color) entering menu: setpoint modification, advanced programming, pin enter

ORBIS

REFERENCE”

DOWNLOAD MANUALS:

Orbis THALOS ELECTRONIC TOUCH SCREEN THERMOSTATS User Manual

OTHER MANUALS:

Orbis THALOS ELECTRONIC TOUCH SCREEN THERMOSTATS Product Specifications Guide

 

ORBIS LOGO

Orbis THALOS ELECTRONIC TOUCH SCREEN THERMOSTATS User Manual

Leave a Reply

Your email address will not be published. Required fields are marked *

To respond on your own website, enter the URL of your response which should contain a link to this post's permalink URL. Your response will then appear (possibly after moderation) on this page. Want to update or remove your response? Update or delete your post and re-enter your post's URL again. (Find out more about Webmentions.)