Neomitis TMR7a DIGITAL ROOM THERMOSTAT OPERATING INSTRUCTIONS

Neomitis TMR7a DIGITAL ROOM THERMOSTAT

OVERVIEW

Thank you for purchasing our TMR7, 7-day single-channel digital timer.
It is by listening to your requirements we have created and designed our products to be easy to operate and install.
It is this ease of operation that is intended to make your life easier and help you save energy and money.

CONTROLS AND DISPLAY

• Timer 
• LCD Display

SETTINGS

INITIAL POWER UP

1. Switch on the timer power supply. All symbols will be displayed on the LCD screen as shown for two seconds.
2. After 2 seconds, the LCD will show:
   • The default time and day
   • Run icon solid
   • CH systems is OFF
     Note: A low battery level indicator will appear in the display when the battery must be changed.
     Remember to take used batteries to a battery collection point so they can be recycled.

PROGRAMMING

Note: The unit is already set with the correct date and time. Should the timer need resetting for any reason, please see the instructions.

SET THE CH/Z1 PROGRAMMING

1. Move the Programming slider to position prog.
   All days of the week are solid. Underscore and Yes/ No are flashing.
2. Press day if you want to set another day of the week. Underscore moves under the other days. Then press yes to program the underscored day.
3. Press + or – to increment/decrement the first On/Off period start time.
   Then press yes to confirm.
4. Press+ or –to increment/decrement the first On/Off period end time.
   Then press Yes to confirm.
5. Repeat for the second On/Off period and for the third On/Off period. (Please refer to the advanced installer settings on Installation instruction to enable the third On/Off period).
   

   On/Off periods	Default schedule
   Two On/Off periods settings
   Period 1	Start at 06:30 am	End at 08:30 am
   Period 2	Start at 05:00 pm	End at 10:00 pm
   Three On/Off periods settings
   Period 1	Start at 06:30 am	End at 08:30 am
   Period 2	Start at 12:00 pm	End at 02:00 pm
   Period 3	Start at 05:00 pm	End at 10:00 pm

6. The current program can be copied to the next few days. Press Yes to copy or No to program manually the next day.
7. When finished, move the program slider to the RUN position to confirm.

OPERATING

MODE SELECTION AND DESCRIPTION

Mode slider sequences for CH/Z1: Constant all day auto off

• Constant: Permanent ON mode. The system is permanently turned ON.
• All day: The system turns ON from the first On period start time until the last Off period end time of the current day.
• Auto: Automatic mode. The unit is controlling to the programming that has been selected (refer to the “Programming” section page 2).
• Off: Permanent Off mode. The system stays Off permanently. The boost mode can be still used.

BOOST

BOOST: Boost mode is a temporary mode that allows you to switch ON for 1, 2 or 3 hours. At the end of set period, the device will revert to its prior setting.
BOOST will work from any running mode.
BOOST is entered by pressing BOOST button.
Press 1 time to set 1 hour, 2 times to set 2 hours, and 3 times to set 3 hours.
BOOST is canceled by pressing again on Boost or movement of sliders.
When BOOST is running the end of the Boost period is shown for each system.

Note:

• The Programming slider must be in the RUN position.
• There will be a slight delay between pressing BOOST and activation of the relay.

ADVANCE

Advance: advance mode is a temporary mode that allows you to switch ON the system in advance, until the next On/Off period end time.
Press ADV button to activate this mode.
Press ADV again button to disable it before the end.

HOLIDAY

Holiday: Holiday mode allows to switch off the heating (or Z1) for a specified number of days, adjustable between 1 and 99 days.
To set the holiday function:

1. Press Day button for 5 seconds.
2. OFF appears on the display. Press or to increment or decrement the number of days.
3. Then press YES to confirm. the heating (or Z1) switch Off and the number of remaining days will count down on display.
4.  To cancel the holiday function, press DAY button.

REVIEW

Review: Review mode allows to review all programming at one time. The review starts from the beginning of the week and each steps appear every 2 seconds.
Press the Review button to start the programming review.
Press again to go back on normal operating mode.

FACTORY SETTINGS

Note: To restore factory settings, press and hold down this part for more than 3 seconds using the tip of a pen.
All LCD displays will be turned ON for 2 seconds and the factory settings will be restored.

SET DATE AND CLOCK

1. Move the Programming slider to the position.
   The preset year is solid.
2. To select the current year, press +, to increment the year.
   Press –, to decrement the year.
   Press YES to confirm and set the current month.
3. The preset month appears.
   Press +to increment the month.
   Press – to decrement the month.
   Press YES to confirm and set the current day.
4. The preset day appears.
   Press+ to increment the day.
   Press –to decrement the day.
   Press YES to confirm and set the clock.
   01 = January ; 02 = February ; 03 = March ; 04 = April ; 05 = May ; 06 = June ; 07 = July ; 08 = August ; 09 = September ; 10 = October ; 11 = November ; 12 = December
5. The preset time appears.
   Press to increment the time.
   Press to decrement the time.
   Move the program slider to any other position to confirm/finish this setting.

TROUBLESHOOTING

• The display disappears on the timer: – Check the fused spur supply.
  The heating does not come on:
  • If the CH Indicator light is on then it is unlikely to be a fault with the timer.
  • If the CH indicator light is NOT ON then check the program and then try BOOST as this should operate in any position.
  • Check that your room thermostat is calling for heat.
  • Check that the boiler is on.
  • Check that your pump is working.
  • Check that your motorized valve if fitted has opened.
    If the problem persists contact your installer
    Note: If Service due soon or service due appears in the display please contact your landlord.

TECHNICAL SPECIFICATIONS

Please refer to the installing instructions for any information about, standards and product environment.

NOTE

In some instances, the unit may have been set with the service interval function enabled.
By Law in rented accommodation, your gas boiler should be inspected/serviced annually to ensure it is working correctly.
This option is designed to remind the end user to contact the relevant person to have the annual service carried out on the boiler.
This function will be enabled and programmed by your Installer, maintenance Engineer, or Landlord.
If it has been set to do so, the unit will display a message on the screen to remind you that a boiler service is due.
The Service Due Soon countdown will be indicated up to 50 days before the Service is due to allow time to arrange for an engineer to attend, normal functions will continue during this stage.
At the end of this service due soon period, the unit will go to Service Due OFF at which point only the 1hour boost will operate on TMR7 and PRG7, if the unit is a thermostat RT1/RT7, it will operate at 20°C during this hour.
If PRG7 RF, Thermostat has no function.

WHAT IS A TIMER ?

…an Explanation for Householders. Programmers allow you to set ‘On’ and ‘Off’ time periods. Some models switch the central heating and domestic hot water on and off at the same time, while others allow the domestic hot water and heating to come on and go off at different times. Set the ‘On’ and ‘Off’ time periods to suit your own lifestyle. On some timers, you must also set whether you want the heating and hot water to run continuously, run under the chosen ‘On’ and ‘Off’ heating periods, or be permanently off. The time on the timer must be correct. Some types have to be adjusted in spring and autumn at the changes between Greenwich Mean Time and British Summer Time. You may be able to temporarily adjust the heating program, for example, ‘Advance’, or ‘Boost’. These are explained in the manufacturer’s instructions. The heating will not work if the room thermostat has switched the heating off. And, if you have a hot-water cylinder, the water heating will not work if the cylinder thermostat detects that the hot water has reached the correct temperature.

NEOMITIS® LIMITED – 16 Great Queen Street, Covent Garden, London, WC2B 5AH UNITED KINGDOM
Registered in England and Wales No: 9543404
Tel: +44 (0) 2071 250 236
Fax: +44 (0) 2071 250 267
E-mail: [email protected]

www.neomitis.com

REFERENCE:

DOWNLOAD MANUALS:

Neomitis TMR7a DIGITAL ROOM THERMOSTAT OPERATING INSTRUCTIONS

OTHER MANUALS:

Neomitis TMR7a DIGITAL ROOM THERMOSTAT INSTALLATION INSTRUCTIONS

Neomitis TMR7a DIGITAL ROOM THERMOSTAT OPERATING INSTRUCTIONS