Neomitis RT0 RF WIRELESS ROOM THERMOSTAT AND OPERATING INSTRUCTIONS

Neomitis RT0 RF WIRELESS ROOM THERMOSTAT 

OVERVIEW

Thank you for purchasing our RT0 RF, wireless digital room thermostat. It is by listening to your requirements we have created and designed our products to be easy to operate and install.
It is this ease of operation that is intended to make your life easier and help you save energy and money.

CONTROLS AND DISPLAY

Thermostat

LCD Display

SETTINGS

INITIAL POWER UP 

1. To start: insert the two AA batteries provided into the battery compartment.
   Once batteries are fitted all symbols will be displayed on the LCD screen as shown for two seconds.
2. After 2 seconds, the LCD will show:
   The ambient temperature (°C) solid.
   The icon is solid when the heating is turned ON.
   The setpoint temperature (°C) solid. RF icon flashes.Note: When the batteries must be changed, a low battery level indicator appears on the device. Remember to take used batteries to battery collection points so they can be recycled.

PAIRING PROCEDURE

The thermostat and the receiver are not bonded together at the factory. To bond the transmitter and the receiver together, proceed as below:

1. Press and hold for 5 seconds the RF test button on the receiver. RF test green light is blinking.
2. Within 1 minute, press and hold for 5 seconds the RF test button on the thermostat. Pairing icon is flashing.
3. Thermostat RF icon and recei-ver green light are blinking.
4. Thermostat RF icon and receiver green light will be solid when pairing is complete.

Note: the receiver is usually located near your boiler.

TEMPERATURES SETTING

The desired temperature can be set.

1. To set the temperature, turn the dial clockwise, to increment the temperature, turn the dial counter-clockwise, to decrement the tempera-ture. The default temperature is 20°C (68°F).

FACTORY SETTINGS

Note: To restore factory settings, press and hold down this part for more than 3 seconds using the tip of a pen. All LCD display will be turned ON for 2 seconds and the factory settings will be restored.

TROUBLESHOOTING

The boiler is not heating:

• Check that the thermostat is calling for heat if yes then the thermostat would appear to be working check that the boiler has not switched itself off.
• If no increase set temperature.
• Check the position of the batteries. Remove them for 30 seconds and reinsert them. If the problem persists, replace the 2 batteries.

Nothing in the display:

• Check the position of the batteries. Remove them for 30 seconds and reinsert them. If the problem persists, replace the 2 batteries.
  The room temperature is not high enough, the boiler is not providing enough heat:
• Check the active desired temperature and increase it if need be (see page 1).

You made a mistake while setting:

• You just need to restore factory settings, as explained in the “Factory settings” section (see page 2). This will reverse any changes you might have made.

The system is not heating but is on:

• If and indicator light is on but the system remains cold, then you should contact your installer.
• If the problem persists, then contact your installer.

TECHNICAL SPECIFICATIONS

Please refer to the installing instructions for any informations about batte-ries life, standards and product environment.

WHAT IS A ROOM THERMOSTAT 
an explanation for householders A room thermostat simply switches the heating system on and off as necessary. It works by sensing the air temperature, switching on the heating when the air temperature falls below the thermostat setting, and switching it off once this set temperature has been reached. Turning a room thermostat to a hi-gher setting will not make the room heat up any faster. How quickly the room heats up depends on the de-sign of the heating system, for example, the size of boiler and radiators. Neither does the setting affect how quickly the room cools down. Turning a room thermostat to a lower setting will result in the room being controlled at a lower temperature, and saves energy.
The heating system will not work if a time switch or programmer has swit-ched it off. The way to set and use your room thermostat is to find the lowest temperature setting that you are comfortable with, and then leave it alone to do its job. The best way to do this is to set the room thermostat to a low temperature – say 18ºC – and then turn it up by one degree each day until you are comfortable with the temperature. You won’t have to adjust the thermostat further. Any adjustment above this setting will waste energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only one room thermostat to control the whole house. But you can have diffe-rent temperatures in individual rooms by installing thermostatic radiator valves (TRVs) on individual radiators. If you don’t have TRVs, you should choose a temperature that is reasonable for the whole house. If you do have TRVs, you can choose a slightly higher setting to make sure that even the coldest room is comfortable, then prevent any overheating in other rooms by adjusting the TRVs.
Room thermostats need a free flow of air to sense the temperature, so they must not be covered by curtains or blocked by furniture. Nearby electric fires, televisions, wall or table lamps may prevent the thermostat from working properly.

Creating innovative solutions for ambient comfort NEOMITIS® LIMITED – 4th Floor, Lincoln House, 300 High Holborn, London WC1V 7JH Registered in England and Wales No: 9543404
Tel: +44 (0) 2071 250 236
Fax: +44 (0) 2071 250 267
E-mail: [email protected]
www.neomitis.com

Other Manuals

Neomitis RT0 RF WIRELESS ROOM THERMOSTAT AND RECEIVER Installation Guide

Neomitis RT0 RF WIRELESS Digital ROOM THERMOSTAT Technical Spacification Guide

Neomitis RT0 RF WIRELESS ROOM THERMOSTAT ANDOPERATING INSTRUCTIONS