Levoit LTM-A401S-WUS Programmable Thermostat USER MANUAL

Levoit LTM-A401S-WUS Programmable Thermostat 

What You’ll Need

• Electric drill
• 3/16-inch drill bit
• Small flat head screwdriver
• Philips head screwdriver

Specifications

Power Supply	AC 24V, 60Hz
Rated Power	3W
Dimensions	4.68 x 3.49 x 0.98 in / 11.88 x 8.86 x 2.50 cm
Weight	0.37 lb / 0.17 kg
Connectivity	2.4GHz Wi-Fi (802.11 b/g/n), Zigbee 3.0 (for room sensors)
Temperature Range	Setting Range: 32°–99°F / 0°–37°C Display Range: 32°–104°F / 0°–40°C   Note: The thermostat settings are limited to 99°F. However, the thermostat can read up to 104°F.

Temperature Increments	1°F / 0.5°C
Relative Humidity (RH) Display Range	0–99%
Relative Humidity (RH) Increments	1%
Operating Conditions	Temperature: 32°–122°F / 0°–50°C   Relative Humidity: 5–95% (non-condensing)
Storage Conditions	Temperature: -4°–140°F / -20°–60°C   Relative Humidity: 5–95% (non-condensing)

Compatibility

•  2H/2C Conventional Systems
•  4H/2C Heat Pump Systems or Dual Fuel Systems
•  Systems with Rc and Rh Terminals (for separate heating and cooling power supplies)

Installation

• Before installing and wiring, TURN OFF your HVAC system by turning off the appropriate switch or locking the appropriate circuit breaker in the OFF position.
•  Only install the thermostat if you are comfortable with electrical work. If not, contact a qualified electrician. Improper installation will increase risk of fire, electric shock, and other injuries.
•  The thermostat must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code.
•  Do not install the thermostat with wet hands

General Safety

• Only install and use the thermostat indoors, in a dry location, and avoiding extreme heat and freezing temperatures.
• Do not modify the thermostat hardware or software.
• Not for commercial use. Household use only.

Function Diagram

• A. Smart Thermostat
• B. Backplate
• C. Power Extender Kit (PEK)

Removing Your Old Thermostat

•  Turn off your HVAC system
•  Remove your old thermostat
• Check for compatibility
•  Take a photo
•  Find the Thermostat Labels in the included wire tag set. Label the wires according to the corresponding terminals. [Figure 1.5]
•  Carefully disconnect the wires. Each thermostat is different, but usually, you use a Philips head screwdriver to loosen a screw or press a release button to remove the wire.

Installing Thermostat with a C Wire

• Remove the old backplate
• Attach the new backplate
• Connect the wires
• Adjust the jumper (DIP switch)
• Place the thermostat
• Turn on your HVAC system

About R Wires

•  If you have more than one R wire (R wires include R, Rc, and Rh):
•  Connect the R or Rc wire to the Rc terminal, and connect the Rh wire to the Rh terminal.
•  If you only have one R wire (R wires include R, Rc, and Rh):
•  Connect the R wire—R, Rc, or Rh—to the Rc terminal.

Installing Thermostat without a C Wire
If your system does not have a C wire, you must install the power extender kit (PEK). The PEK connects to your thermostat wires to create a circuit that provides power to your thermostat.

Power Extender Kit (PEK)

• The PEK has 4 terminals on one side and 5 terminals on the other side.
•  The side with 4 terminals is not pre-wired. Connect the thermostat wires to the terminals.
•  The side with 5 terminals is pre-wired to connect to your HVAC control board.

Compatibility
The power extender kit (PEK) requires that your HVAC system has one of the following sets of wires:

• 4 Wires: W/W1, Y/Y1, G, and R (including Rc or Rh)
• 3 Wires: Y/Y1, G, and R (including Rc or Rh)

If your HVAC does not have these wires, your system may not be compatible with the PEK.

•  Identify the thermostat terminals on your HVAC
•  Label the thermostat wires
•  Disconnect the thermostat wires
•  Connect the thermostat wires to the PEK
•  Connect the PEK wires to the control board
•  Position the PEK
•  Remove the old backplate
• Attach the new backplate
•  Connect the wires
•  Adjust the jumper (DIP switch)
• Place the thermostat
• Turn on your HVAC system

Wiring Diagrams

The following are wiring diagrams for common HVAC systems. You may be able to use these for reference when installing your thermostat

Conventional Heating/Cooling System – C Wire

Conventional Heating/Cooling System – No C Wire (Used with PEK)

Heat Pump (Air or Geothermal) with Auxiliary Heat – C Wire

Heat Pump (Air or Geothermal) with Auxiliary Heat – No C Wire (Used with PEK)

Heat Pump (Air or Geothermal) with Auxiliary Heat, Two Transformer System – C Wire

Getting Started

Setup Wizard & Configuration

• When the thermostat first powers on, the welcome screen will appear. Begin the setup wizard.
• Refer to the photo of the backplate terminals to find which terminals have wires connected to them, then select these terminals on the screen
• Select the type of fuel system your furnace uses. This will affect how the fan works during heating.
• Select your desired Eco Level.
• Select whether you would like to connect the thermostat to the VeSync app (see VeSync App Setup, page 59). If you don’t want to connect to VeSync right now, you can do it later.
• Set your time zone and current time
• The setup wizard is complete. To start your thermostat, select an HVAC mode (see HVAC Modes, on page 45).

Basic Functions

Note: The smart thermostat is continually being improved and may change over time. If there are any differences, follow the on-screen instructions.

Home Screen

Standby Screen
The Standby Screen will display after a period of no activity. You can customize the standby screen timeout in the Settings, page 56).

HVAC Modes

• Heat: Heating only
• Cool: Cooling only
• Auto: The thermostat will automatically adjust heating/cooling to reach a target temperature range.
  Smart: The thermostat will automatically adjust heating/cooling to reach a set target temperature.
• Auxiliary Heat: Use Auxiliary Heat to warm up the room faster if the heat pump is not sufficient
• Off: Turns off heating and cooling

Fan Modes

• On: The fan runs continuously.
• Auto: The fan automatically turns on when the HVAC is cooling or heating.

Weather
Use the Weather screen to view the latest weather information, including high and low temperatures, humidity, and the upcoming forecast

Menu
Press the Me nal functions and settings.

Schedule

• Use the Schedule screen to automatically run routines throughout the day. The thermostat comes with a default schedule that includes 4 routines per day, which you can customize according to your preferences.
• Swipe left to delete a scheduled routine. If the first routine in a schedule is deleted, the thermostat will automatically continue the last routine from the previous day.

Default Schedule Settings

Weekdays		Weekends
Home	6:00 AM	Home	8:00 AM
Away	8:00 AM	Away	10:00 AM
Home	6:00 PM	Home	6:00 PM
Sleep	10:00 PM	Sleep	10:00 PM

My Routines
Use the My Routines screen to save temperature and thermostat preferences for different situations. The thermostat comes with 3 preset routines—Home, Away, and Sleep—which you can customize according to your preferences. You can also create custom routines for different situations, such as for dinner or exercising. If you have individual room sensors (sold separately), you can choose which sensors are active during each routine. To buy official Levoit room sensors, contact Customer Support (see page 73). You can use the schedule to automatically run routines (see Schedule, page 49).

Usage
 Use the Usage screen to view your heating and cooling usage over the past week.

Vacation
Use the Vacation screen to input your vacations, and set what the thermostat should do during those vacations. You can set departure and return dates, as well as a temperature range and fan setting for the thermostat to use.

Sensors
Use the Sensors screen to view the thermostat sensor and additional sensors (sold separately). View the sensors’ current temperature, humidity reading, online status, and remaining battery life. Room sensors can help eliminate hot and cold spots, prioritize certain rooms, and be used with routines. Sensors must be paired to your thermostat through the VeSync app. Add the thermostat and room sensor to the same VeSync Home and the sensor will automatically pair with the thermostat.

Notifications
Use the Notifications screen to view any recent notifications, as well as set reminders and alerts. You can set reminders for when to replace an air filter or perform HVAC maintenance. You can also choose to be alerted if there is a problem with your HVAC system or the temperature in your home exceeds a designated safe range.

Settings
Use the Settings screen to customize additional settings for your thermostat, such as screen brightness, temperature unit, display lock, and more.

Advanced Settings
WARNING: Adjusting these setting without guidance may cause damage to your HVAC system. We recommend consulting a HVAC professional before adjusting advanced settings. Use the Advanced Settings screen to fine-tune your thermostat settings. Follow on-screen instructions for more details.

My VeSync
Use the My VeSync screen to view your linked VeSync account information. You can also use this screen to register or re-register your thermostat if necessary.

VeSync App Setup

• To download the VeSync app, scan the QR code or search “VeSync” in the Apple App Store® or Google Play Store

• Open the VeSync app. If you already have an account, tap Log In. To create a new account, tap Sign Up.
• Tap + and select your smart thermostat.
• Follow the in-app instructions to set up your smart thermostat.

Connect with Amazon Alexa or Google Assistant
You can use the VeSync app to connect your smart thermostat to Amazon Alexa or Google Assistant™. Please follow the in-app instructions to set up your voice assistant.

VeSync App Functions
The VeSync app allows you to access additional smart thermostat functions, including those listed below. As the app develops, more features may become available.

• Remote Control
  • Control your thermostat from anywhere using the
• VeSync app.
  • Connect your thermostat to third-party voice assistants.
• Schedules
  • Create and customize heating and cooling schedules for every day of the week.
• Smart Scenes
  • Prioritize comfort and air quality in your home using
  • Smart Scenes, which can control your Levoit thermostat, humidifier, and air purifier settings all at the same time.
• Energy Usage Graphs
  • View your thermostat energy usage and how much time the thermostat spent heating/cooling.
  •  See your energy usage history for the previous week.

Troubleshooting

Problem	Possible Solution
The thermostat display does not turn on.	Gently tug on each wire connected to the terminals on the backplate to make sure they are properly inserted and secure.
	Make sure the cover of your HVAC system is completely closed. Some HVAC systems do not turn on if the cover is not closed.
	If you only have one R wire (R wires include R, Rc, and Rh), make sure the R wire is connected to the Rc terminal (see About R Wires, page 18).
	If you are using the PEK, make sure the wires are connected to the correct terminals on the backplate (see step 9 of Installing Thermostat without a C Wire, page 32).
	Use a multimeter to check the voltage of the C wire and Rc wire to make sure it is AC 18–30V. The thermostat does not work with high voltage systems. Contact Customer Support (see page 73).
The thermostat freezes or crashes.	Remove the thermostat from the backplate, then reattach it. This will restart the thermostat.

Problem	Possible Solution
Forgot lock screen password.	Unlock the thermostat through the VeSync app.
	Remove the thermostat from the backplate, then reattach it. This will restart the thermostat.
Heating and cooling functions are reversed.	If you have a heat pump system, change the O/B reversing valve setting in the thermostat’s settings (see Settings, page 56).
	Make sure that the W wire and Y wire are connected to the correct terminals on the backplate.
	If you are using the PEK, make sure the wires are connected to the correct terminals on the HVAC control board and backplate (see Installing Thermostat without a C Wire, page 22).
The thermostat does not show weather information.	Make sure the thermostat is connected to the VeSync app.
	In the VeSync app, make sure you input your home location and set the region to the United States.

Problem	Possible Solution
Room sensor (sold separately) does not connect to the thermostat.	Make sure the thermostat and room sensor are added to the same VeSync account.
	One of the room sensor’s batteries may be low. Replace with 2 AAA batteries.

• My smart thermostat isn’t connecting to the VeSync app.
• Make sure your phone has Bluetooth® turned on and is not currently connected to another Bluetooth device.
• During the setup process, you must be on a secure 2.4GHz Wi-Fi® network. Confirm that the network is working correctly.
• Make sure the Wi-Fi password you entered is correct.
• There should be no spaces at the beginning or end of the password.
• Test the password by connecting a different electronic device to the router.
• If you’re manually typing in the SSID and password, double check that both are entered correctly.
• Your phone should be as close as possible to your thermostat.
• Your router may need to be at a higher location, away from obstructions.
•  Make sure your thermostat and router are away from appliances (such as microwave ovens, refrigerators, electronic devices, etc.) to avoid signal interference.
• If you’re using a VPN, make sure it’s turned off while setting up your thermostat.
• Disable portal authentication for your Wi-Fi network. If portal authentication is enabled, the thermostat will not be able to access your Wi-Fi network, and setup will fail.

My thermostat is offline.

•  Make sure your router is connected to the internet and your phone’s network connection is working.
•  Delete your offline thermostat from the VeSync app. Swipe left (iOS®) or press and hold (Android™), then tap Delete Reconfigure the thermostat with the VeSync app.

Warranty

Product Name	Aura™ Smart Thermostat
Model	LTM-A401S-WUS
For your own reference, we strongly recommend that you record your order ID and date of purchase.
Date of Purchase
Order ID

Levoit Limited Product Warranty
Register your products at https://warranty.levoit.com/warranty to stay up to date with important product information such as product updates, limited warranties, usage and maintenance recommendations, and notifications concerning safety warnings or product recalls. Registration is not required to claim your limited warranty.

Two (2) Year Limited Consumer Product Warranty
Arovast Corporation (“Arovast”) warrants that the product shall be free from defects in material and workmanship for a period of 2 years from the date of original purchase (“Limited Warranty Period”), provided the product was used in accordance with its use and care instructions (e.g., in the intended environment and under normal circumstances).

Your Limited Warranty Benefits
During the Limited Warranty Period and subject to this limited Warranty Policy, Arovast will, in its sole and exclusive discretion, either (i) refund the purchase price if the purchase was made directly from the online Levoit store, (ii) repair any defects in material or workmanship, (iii) replace the product with another product of equal or greater value, or (iv) provide store credit in the amount of the purchase price.

Who is Covered?
This limited warranty extends only to the original consumer purchaser of the product and is not transferable to any subsequent owner of the product, regardless of whether the product transferred ownership during the specified term of the limited warranty. The original consumer purchaser must provide verification of the defect or malfunction and proof of the date of purchase to claim the Limited Warranty Benefits.

Be Aware of Unauthorized Dealers or Sellers
This limited warranty does not extend to products purchased from unauthorized dealers or sellers. Arovast’s limited warranty only extends to products purchased from authorized dealers or sellers that are subject to Arovast’s quality controls and have agreed to follow its quality controls. Please be aware, products purchased from an unauthorized website or dealer may be counterfeit, used, defective, or may not be designed for use in your country. You can protect yourself and your products by making sure you only purchase from Arovast or its authorized dealers. If you have any questions about a specific seller, or if you think you may have purchased your product from an unauthorized seller, please contact our Customer Support Team via [email protected].

What’s Not Covered?

• Normal wear and tear, including parts that might wear out over time (e.g., batteries, filters, cleaning brush, essential oil pads, etc.).
• If the proof-of-purchase has been altered in any way or is made illegible.
• If the model number, serial number or production date code on the product has been altered, removed or made illegible.
• If the product has been modified from its original condition.
• If the product has not been used in accordance with directions and instructions in the user manual.
• Damages caused by connecting peripherals, additional equipment or accessories other than those recommended in the user manual.
• Damages or defects caused by accident, abuse, misuse, or improper or inadequate maintenance.
• Damages or defects caused by service or repair of the product performed by an unauthorized service provider or by anyone other than Arovast.
• Damages or defects occur during commercial use, rental use, or any use for which the product is not intended.
• If the unit has been damaged, including but not limited to damage by animals, lightning, abnormal voltage, fire, natural disaster, transportation, dishwasher, or water (unless the user manual expressly states that the product is dishwasher-safe).
• Incidental and consequential damages.
• Damages or defects exceeding the cost of the product.
• Claiming Your Limited Warranty Service in 5 Simple Steps:
• Make sure your product is within the specified limited warranty period.
• Make sure you have a copy of the invoice and order ID or proof of purchase.
• Make sure you have your product. DO NOT dispose of your product before contacting us.
• Contact our Customer Support Team via [email protected]
• Once our Customer Support Team has approved your request, please return the product with a copy of the invoice and order ID.

Sole and Exclusive Remedy
THE FOREGOING LIMITED WARRANTY CONSTITUTES AROVAST CORPORATION’S EXCLUSIVE LIABILITY, AND YOUR SOLE AND EXCLUSIVE REMEDY, FOR ANY BREACH OF ANY WARRANTY OR OTHER NONCONFORMITY OF THE PRODUCT COVERED BY THIS LIMITED PRODUCT WARRANTY STATEMENT. THIS LIMITED WARRANTY IS EXCLUSIVE, AND IN LIEU OF ALL OTHER WARRANTIES. NO EMPLOYEE OF AROVAST CORPORATION OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY IN ADDITION TO THE LIMITED WARRANTY IN THIS LIMITED PRODUCT WARRANTY STATEMENT.

Disclaimer of Limited Warranties
TO THE FULLEST EXTENT PROVIDED BY APPLICABLE LAW, EXCEPT AS WARRANTED IN THIS LIMITED PRODUCT WARRANTY POLICY, AROVAST CORPORATION PROVIDES THE PRODUCTS YOU PURCHASE FROM AROVAST CORPORATION “AS IS” AND AROVAST CORPORATION HEREBY DISCLAIMS ALL WARRANTIES OF ANY KIND, WHETHER EXPRESS OR IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR PARTICULAR PURPOSE.

Limitations of Liability
TO THE FULLEST EXTENT PROVIDED BY APPLICABLE LAW, IN NO EVENT WILL AROVAST CORPORATION, ITS AFFILIATES, OR THEIR LICENSORS, SERVICE PROVIDERS, EMPLOYEES, AGENTS, OFFICERS, OR DIRECTORS BE LIABLE FOR:

•  DAMAGES OF ANY KIND ARISING OUT OF OR IN CONNECTION WITH PRODUCTS PURCHASED FROM AROVAST CORPORATION IN EXCESS OF THE PURCHASE PRICE PAID BY THE PURCHASER FOR SUCH PRODUCTS, OR
•  INDIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR PUNITIVE DAMAGES EVEN IF AROVAST CORPORATION OR ONE OF ITS SUPPLIERS HAS BEEN ADVISED OF THE POSSIBILITY OR LIKELIHOOD OF SUCH DAMAGES.

AND REGARDLESS OF WHETHER CAUSED BY TORT (INCLUDING NEGLIGENCE), BREACH OF CONTRACT, OR OTHERWISE. OUR LIABILITY SHALL UNDER NO CIRCUMSTANCES EXCEED THE ACTUAL AMOUNT PAID BY YOU FOR THE DEFECTIVE PRODUCT, NOR SHALL WE UNDER ANY CIRCUMSTANCES BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, SPECIAL OR PUNITIVE DAMAGES OR LOSSES, WHETHER DIRECT OR INDIRECT. EXCEPT AS COVERED BY THIS LIMITED PRODUCT WARRANTY STATEMENT, AROVAST CORPORATION SHALL NOT BE LIABLE FOR COSTS ASSOCIATED WITH THE REPLACEMENT OR REPAIR OF PRODUCTS PURCHASED FROM IT, INCLUDING, BUT NOT LIMITED TO, LABOR, INSTALLATION, OR OTHER COSTS INCURRED BY THE USER AND, IN PARTICULAR, ANY COSTS RELATING TO THE REMOVAL OR REPLACEMENT OF ANY PRODUCT

OTHER RIGHTS YOU MAY HAVE
SOME JURISDICTIONS DO NOT ALLOW FOR: (1) EXCLUSION OF IMPLIED WARRANTIES; (2) LIMITATION ON THE DURATION OF IMPLIED WARRANTIES; AND/OR (3) EXCLUSION OR LIMIATION OF INCIDENTAL OR CONSEQUANTIAL DAMAGES; SO THE DISCLAIMERS IN THIS POLICY MAY NOT APPLY TO YOU. IN THESE JURISDICTIONS YOU HAVE ONLY THE IMPLIED WARRANTIES THAT ARE EXPRESSLY REQUIRED TO BE PROVIDED IN ACCORDANCE WITH APPLICABLE LAW. THE LIMITATIONS OF WARRANTIES, LIABILITY, AND REMEDIES APPLY TO THE MAXIMUM EXTENT PERMITTED BY LAW. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS IN YOUR JURISDICTION. THIS STATEMENT OF LIMITED WARRANTY IS SUBJECT TO APPLICABLE LAWS THAT APPLY TO YOU AND THE PRODUCT. PLEASE REVIEW THE LAWS IN YOUR JURISDICTION TO UNDERSTAND YOUR RIGHTS FULLY.

CHANGES TO THIS POLICY
We may change the terms and availability of this limited warranty at our discretion, but any changes will not be retroactive.

Attributions

• Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.
• App Store® is a trademark of Apple Inc.
• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Arovast Corporation is under license. Other trademarks and trade names are those of their respective owners.
• Google, Android, and Google Play are trademarks of Google LLC.
• iOS is a registered trademark of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.
• Zigbee Alliance’s trademarks and logos, and all goodwill associated therewith, are the exclusive property of the Zigbee Alliance.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

Customer Support
If you have any questions or concerns about your new product, please contact our helpful Customer Support Team.

• Arovast Corporation
• 1202 N. Miller St., Suite A
• Anaheim, CA 92806
• Support Hours
• Mon–Fri, 9:00 am–5:00 pm PST/PDT
• Email: [email protected]
• Toll-Free: (888) 726-8520

REFERENCE:

DOWNLOAD MANUALS:

Levoit LTM-A401S-WUS Programmable Thermostat USER MANUAL

Levoit LTM-A401S-WUS Programmable Thermostat USER MANUAL