Honeywell T8775A the Digital Round Non-Programmable Thermostat Product Data

Honeywell T8775A the Digital Round Non-Programmable Thermostat

FEATURES

• Attractive styling complements any decor.
• Simple to use. Turn the dial to adjust the setpoint temperature.
• Large easy-to-read display. The temperature reading is easily seen from a distance.
• Backlit display. On-demand backlighting makes it easy to read the display in a dark room or hallway.
• No batteries are required. The setpoint temperature is held permanently in memory in the event of a power failure.
• Powered through heating-cooling system controls.
• System and Fan switches on the T8775C model.
• The manual changeover from heat to cool on T8775C model.
• Easy installation and set up saves time and increase installer productivity.
• Easily configurable by the use of DIP switches.
• Fahrenheit or Celsius temperature display for added flexibility.
• Selectable heating cycle rates (1, 3, 6, 9 CPH) for a variety of applications.
• The cooling cycle rate is fixed at 3 CPH. This is the standard compressor setting.
• Minimum off-time for the compressor in the cooling mode. Protects and extends the life of the equipment.
• The decorative cover plate is available to cover marks on the wall or to mount the T8775 Thermostat to an electrical box.

SPECIFICATIONS

IMPORTANT

The specifications given in this publication do not include normal manufacturing tolerances; therefore, an individual unit might not exactly match the listed specifications. Also, this product is tested and calibrated under closely controlled conditions, and some minor differences in performance can be expected if those conditions are changed.

Models:
T8775A and T8775C TRADELINE® models include a thermostat, wallplate for mounting and wiring, mounting hardware, 4074FAB resistor, installation instructions and an owner’s guide.

Electrical Ratings:
24 Vac nominal: 18 Vac to 30 Vac, 60Hz.
Heating: .02 to 1.5 A run; 3.5A inrush.
Cooling: .02 to 1.5 A run; 6.0 A inrush.
Fan: .02 to 0.5 A run; 2.5A inrush.

Temperature Ratings:
Setting Range:
40°F to 90°F (4.5°C to 32.0°C) in heating.
45°F to 99°F (7.0°C to 37.0°C) in cooling.

Ambient Range:
40°F to 110°F (4.4°C to 43.3°C).

Shipping Temperature Range:
-20°F to 120°F (-28.9°C to 48.9°C).
Humidity Ratings: 5% to 90% RH, non-condensing.

Mounting Hardware:
Sheet metal screws: Two 1-in. (25 mm) 4-24, type AB. Drywall anchors: Two conical anchors, 3/16 in. (5 mm)
diameter by ¾ in. (19 mm) length.

4074 FAB Resistor:
1 Kohm, 3 Watts.
Installation Instructions packed with resistor.
Batteries: Not required.
Finish: Premier White®.

Accessories:
50000066-001 Decorative Cover Plate. Used to cover wall
marks, or to mount T8775 Thermostat to an electrical box. 32007680-001 Cover Ring.
Dimensions: See Fig. 1.

ORDERING INFORMATION

When purchasing replacement and modernization products from your TRADELINE® wholesaler or distributor, refer to the TRADELINE® Catalog or price sheets for the complete ordering number.
If you have additional questions, need further information, or would like to comment on our products or services, please write or phone:

1. Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory).
2. Honeywell Customer Care 1885 Douglas Drive North
   Minneapolis, Minnesota 55422-4386
   In Canada—Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.
   International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France, Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.

INSTALLATION

Separate Wallplate from Thermostat

1. Place your thumbs on top of the thermostat and wallplate. Use your thumbs to pull the thermostat away from the wall plate. See Fig. 3.

Mount Wallplate to Wall
NOTE: Level wallplate for appearance only. The thermostat functions normally even when not mounted level.Mount wallplate to wall (See Fig. 4) as follows:

1. Pull the thermostat wires through the wiring hole on the wallplate.
2. Use a pencil to mark the center of the screw holes on the left and right sides of the wallplate.
3. Remove the wallplate from the wall and drill two 3/16 in.(5 mm) holes in the wall (if drywall) at the locations you marked. For materials such as plaster, drill 7/32 in.
   (6 mm) holes were marked.
4. Tap the provided wall anchors into the drilled holes until they are flush with the wall.
5. Pull the thermostat wires through the wiring hole on the wallplate and reposition the wallplate over the wall anchors.
6. Attach the wallplate to the wall with the screws provided.
7. After wiring the wallplate, plug the hole to prevent drafts from affecting the thermostat; see the Wiring section.

WIRING

IMPORTANT
Use 18-gauge wire to wire the T8775A,C Thermostats.

All wiring must comply with local electrical codes and ordinances. Disconnect the power supply to prevent electrical shock or equipment damage.
NOTE: To ensure proper mounting of the thermostat, restrict all wiring to the shaded area. See Fig. 5.

The shape of the terminals permits insertion of straight or wraparound wiring connections; either method is acceptable. See Fig. 6.

 

Refer to Fig. 7 through 11 for typical wiring diagrams.

1. 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED.
2. REMOVE THE FACTORY-INSTALLED JUMPER BETWEEN R AND RC.
   Fig. 10. Typical hookup of T8775C in a heat-cool system with two transformers.

1. POWER SUPPLY. PROVIDE DISCONNECT MEANS
   AND OVERLOAD PROTECTION AS REQUIRED.
2. FACTORY-INSTALLED JUMPER.
3. USE A JUMPER WIRE (NOT SUPPLIED) TO CONNECT W TO Y.
4. USE EITHER O OR B FOR HEAT PUMP CHANGEOVER.
   Fig. 11. Typical hookup of T8775C in the single-stage heat pump system.

CUSTOMIZE THERMOSTAT

Setting Fuel Switch (T8775C only)
The fuel switch is preset at the factory in the F position. See Fig. 12. This is the correct setting for gas or oil systems. If the T8775C is being installed on an electric heat system, or a heat pump, set the switch to the E position. The E position allows the fan to turn on immediately with the heating equipment in a system where the G terminal is connected.

DIP Switch
To adjust the heat cycle rate or the Fahrenheit/Celsius temperature display, locate DIP switch 1, 2 and 3 on the back of the thermostat. See Fig. 13.

Set Heat Cycle Rate
Use DIP switches 1 and 2 to set the heat cycle rate. See Table 1.

Table 1. Heat Cycle Rate.

Heating System	Cycles Per Hour	DIP Switch 1	DIP Switch 2
Steam, Gravity	1	On	On
High Efficiency Warm Air (90%+ efficiency), Hot Water, Heat Pump	3	Off	On
Gas or Oil Warm Air (factory setting)	6	Off	Off
Electric Warm Air	9	On	Off
In Floor Radiant Heat	Check with the manufacturer for recommended cycle rate.

Fahrenheit/Celsius Indication
Use DIP switch 3 to set the desired temperature indication. See Table 2.

Table 2. Temperature Indication.

Fahrenheit/Celsius Display	DIP Switch 3
Fahrenheit (factory setting)	Off
Celsius	On

Mount Thermostat to Wallplate (see Fig. 14)

SET SYSTEM AND FAN SWITCHES (T8775C ONLY)

SYSTEM Switch: (See Fig.15) 
Heat: The thermostat controls the heating system. Off: Both the heating and cooling systems are off. Cool: The thermostat controls the cooling system.

FAN Switch: (See Fig.15)
Auto: The fan only runs with the heating and cooling system.
On: The fan runs continuously. Use for improved air circulation.

FEATURES AND OPERATION

Features and operation of The Digital RoundTM Thermostat (see Fig. 15 and 16):

• Simple to use. Turn the dial to adjust the temperature setting.
• Large easy-to-read display. The temperature reading is easily seen from a distance.
• Backlit display. On-demand backlighting makes it easy to read the display in a dark room or hallway.
• No batteries required. The temperature setting is held permanently in memory in the event of a power failure.

Backlit Display
Push the backlight button to turn on the backlight (See Fig. 15).
Display Temperature Setpoint

1. Turn the dial one click to display the temperature setpoint. An indicator points to Set when the temperature setpoint is displayed (see Fig.17).
2. If a change to the temperature setpoint is not made within five seconds, the display will switch to the current room temperature. An indicator points to Room when the room temperature is displayed (see Fig. 18).

Adjust Temperature Setpoint
Turn the dial clockwise to raise the temperature setpoint. Turn the dial counterclockwise to lower the temperature setpoint (see Fig. 16).

Power Stealing
The T8775 thermostat steals power from R and W or Rc and Y depending on the system switch position. See Table 3.

Table 3. T8775 Power Stealing.

Power Stealing Circuit
System Switch	T8775A	T8775C
Heat	R and W	R and W
Off	—	R and W
Cool	—	Rc and Y

Table 4. The sequence of Operations.

Fan Switch Settings	System Switch Settings	Call for Action	Energize Terminals	Display Icons
Auto	Off	None	None	None
Auto	Heat	Heating	Wa	Flame
Auto	Cool	Cooling	Y,G	Snowflake
On	Off	Fan	G	None
On	Heat	Heating	W,G	Flame
On	Cool	Cooling	Y,G	Snowflake

a If fuel switch is set to E, both W and G are energized in a call for heat.

CHECKOUT

Cooling (T8775C only)

CAUTION
Low-Temperature Hazard.
Operating at too low of an outdoor temperature may cause compressor damage.
Do not operate cooling if the outdoor temperature is below 50°F (10°C). Refer to the manufacturer’s recommendations.

Minimum Off-Timer
The minimum off-timer in the T8775C Thermostat assures that the cooling compressor does not turn on for at least five minutes after it turns off. The snowflake will flash in the display if there is a call for cooling during the 5-minute off-time.
The following activates the 5-minute minimum-off timer:

• Initial startup
• Power interruption
• Compressor turns off:
  • Setpoint is raised above the room temperature
  • The system switch is changed from the cool mode
  • The thermostat ends the call for cooling
    NOTE: The 5-minute minimum-off timer does not apply to heating.

1. Slide the system switch to COOL and the fan switch to AUTO.
2. Lower the temperature setpoint several degrees below the room temperature.
3. A snowflake will appear in the display and the cooling should turn on.
4. Raise the temperature setpoint several degrees above the room temperature.
5. The snowflake will disappear from the display and the cooling should turn off.

Heating 

1. Slide the system switch to HEAT and the fan switch to AUTO (T8775C only).
2. Raise the temperature setpoint several degrees above the room temperature.
3. A flame will appear in the display and the heat should turn on.
4. Lower the temperature setpoint below the room temper-ature.
5. The flame will disappear from the display and the heat should turn off.

Fan

1. Slide the system switch to OFF and the fan switch to ON. The fan should run continuously.
2. Slide the fan switch to AUTO. The fan should turn off.
   NOTE: Make sure that all equipment responds properly to  the thermostat.

TROUBLESHOOTING GUIDE

Automation and Control Solutions
Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422
Honeywell Limited-Honeywell Limitée 35 Dynamic Drive
Scarborough, Ontario M1V 4Z9

REFERENCE:

Download Manual:   

Honeywell T8775A the Digital Round Non-Programmable Thermostat Product Data

OTHER MANUALS:

Honeywell T8775A the Digital Round Non-Programmable Thermostat Owners Manual

Honeywell T8775A the Digital Round Non-Programmable Thermostat Installation Guide

Honeywell T8775A the Digital Round Non-Programmable Thermostat Product Data