Honeywell LR-HWLV-HVAC TouchPRO Wireless Thermostat
System Types
- Gas, oil, or electric heat with air conditioning
- Warm air, hot water, high efficiency furnaces, heat pumps, steam, gravity
- Heat only — including power to open and close zone valves (Series 20), and normally open zone valves
- Heat only with fan
- Cool only
- 750 mV heating systems
MERCURY NOTICE
This thermostat does not contain mercury. However, do not place your old thermostat in the trash if it contains mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www. thermostat-recycle.org or 800.238.8192 for information on how and where to properly and safely dispose of your old thermostat.This thermostat contains a Lithium battery which may contain Perchlorate material. Perchlorate Material—special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate
Wallplate installation
- Separate wallplate from thermostat.
- Mount wallplate as shown below.
Battery Replacement
The TouchPRO Wireless thermostat has a coin cell battery that retains the time and date during a power failure. Under normal circumstances the coin cell should last five years. Should the time and date need to be reset after a power failure, this is an indication that the coin cell needs to be replaced. You should replace the battery every five years, or before leaving home for an extended period.![Skip to main contentSkip to toolbar About WordPress thermostat.guide 33 updates available 00 Comments in moderation New View Post Performance 1 View Post (AMP) Howdy, wpx_thermostats Log Out Screen OptionsHelp Edit Post Add New A recently published post has been automatically submitted to the Instant Indexing API. Dismiss this notice. Post updated. View post Dismiss this notice. Add title Honeywell LR-HWLV-HVAC TouchPRO Wireless Thermostat Installation Guide Permalink: https://thermostat.guide/honeywell/honeywell-lr-hwl…stallation-guide/ Edit Add MediaAdd PDFVisualText Paragraph P Word count: 1619 Draft saved at 7:10:45 am. Last edited by wpx_thermostats on April 4, 2023 at 7:02 am Move upMove downToggle panel: Yoast SEO Move upMove downToggle panel: Publish Preview Changes(opens in a new tab) Status: Published EditEdit status Visibility: Public EditEdit visibility Revisions: 3 BrowseBrowse revisions Published on: Apr 4, 2023 at 06:47 EditEdit date and time SEO: Not available Readability: OK Purge from cache Move to Trash Move upMove downToggle panel: Show AMP for Current Post? Show Hide Move upMove downToggle panel: Featured image HoneywellHoneywell- LR-HWLV-HVAC- TouchPRO- Wireless -Thermostat- PRO- LR-HWLV-HVAC- TouchPRO- Wireless -Thermostat- FEA Click the image to edit or update Remove featured image Move upMove downToggle panel: Tags Add New Tag Separate tags with commas Remove term: Honeywell HoneywellRemove term: Honeywell LR-HWLV-HVAC Honeywell LR-HWLV-HVACRemove term: Installation Guide Installation GuideRemove term: LR-HWLV-HVAC LR-HWLV-HVACRemove term: LR-HWLV-HVAC Thermostat LR-HWLV-HVAC ThermostatRemove term: TouchPRO Thermostat TouchPRO ThermostatRemove term: TouchPRO Wireless Thermostat TouchPRO Wireless Thermostat Choose from the most used tags Move upMove downToggle panel: Table of Contents The table of contents will be automatic added to this post. Customize Disable TOC Move upMove downToggle panel: Categories All Categories Most Used Honeywell 2GIG ABB Airtouch AIRXCEL Alarm.com American Standard Aprilaire ATAG Aube AVATTO Azel Becasmart Beok Bitron Blaupunkt Boneco Bosch Braeburn Bryant Bryant Housewise bticino Building 36 Busch-Jaeger CADET CARRIER Center Coleman ComfortNet Daikin Danfoss DeLOCK Devolo digitalSTROM Doit DOMETIC Domos Drayton Eaton Eberle Ecobee EcoFactor ECONET ELEKTROBOCK Elgato Emerson EMOS EnerGenie EPH Controls EUROtronic Evolve Exo Terra FAQ Flomasta fontastic Frost Sentry Fujitsu GE APPLIANCES GE-CYNC Gewiss GIRA Google Google Nest Greenlite Hager hama Heat decor Heatdecor Heatit Heatmiser Heatmisser Hitachi Hive Honeywell Home Honeywell AUBE Honeywell Home Honeywell PRO HORSTMANN Hotpoint HQ Hunter ICM Controls ICY Ideal Ideal Halo IEC ILiving Innogy Interlogix intertechno JABLOTRON JUNG KALOR TECH KETOTEK King King Electric Kontakt-Simon Legrand Lennox levoit Lightwave Lux Lux/Go Luxpro Maxx Air Meross Minco Heat MITSUBISHI ELECTRIC Moes Mysa Nedis Nefit Neomitis Nest Labs Nexia NorthQ Nuheat Ojelectronics Orbit OWON Peco Poly Pool Popp Pro1 Pro1 Technologies Proselect Prostat PROSTATE QuietWarmth RADEMACHER Rayotec Remeha Ritetemp Robertshaw Salus Saswell Schluter Systems SCHNEIDER ELECTRIC Secure SENSI Shelly SIEMENS Somfy Stelpro SunStat SUNTOUCH Tado TCS Bays Controls Tekmar Thermosoft Thermostats Trane Uponor Venstar Verdant Vimar Vine Vive WarmlyYours Warmup Waterfurnace Worcester Worcester Bosch Wyze Xavax ZEN ZEN THERMOSTAT + Add New Category Move upMove downToggle panel: Post Attributes Template Default template Move upMove downToggle panel: Custom AMP Editor Use This Content as AMP Content If you want to add some special tags, then please use normal HTML into this area, it will automatically convert them into AMP compatible tags. Add MediaAdd PDFVisualText Paragraph Copy The Content Move upMove downToggle panel: AMP Page Builder Start the AMP Page Builder Move upMove downToggle panel: sameAs Move upMove downToggle panel: Schema Exclude Turn Schema OFF Tick this checkbox to turn off Schema output on this entry. Move upMove downToggle panel: Revisions wpx_thermostats, 8 seconds ago (April 4, 2023 @ 07:02:30) wpx_thermostats, 37 seconds ago (April 4, 2023 @ 07:02:01) [Autosave] wpx_thermostats, 15 mins ago (April 4, 2023 @ 06:47:47) Move upMove downToggle panel: Comments Add Comment No comments yet. Thank you for creating with WordPress.Version 6.2 Close dialog Add media Actions Upload filesMedia Library Filter mediaFilter by type Uploaded to this post Filter by date All dates Search Media list Showing 16 of 16 media items ATTACHMENT DETAILS Honeywell-LR-HWLV-HVAC-TouchPRO-Wireless-Thermostat-3.png April 4, 2023 30 KB 453 by 226 pixels Edit Image Delete permanently Alt Text Learn how to describe the purpose of the image(opens in a new tab). Leave empty if the image is purely decorative.Title Honeywell- LR-HWLV-HVAC- TouchPRO- Wireless -Thermostat- 3 Caption Description File URL: https://thermostat.guide/wp-content/uploads/2023/04/Honeywell-LR-HWLV-HVAC-TouchPRO-Wireless-Thermostat-3.png Copy URL to clipboard ATTACHMENT DISPLAY SETTINGS Alignment Center Link To None Size Full Size – 453 × 226 Selected media actions 1 item selected Honeywell- LR-HWLV-HVAC- TouchPRO- Wireless -Thermostat- 3](https://thermostat.guide/wp-content/uploads/2023/04/Honeywell-LR-HWLV-HVAC-TouchPRO-Wireless-Thermostat-3.png)
Power Requirements
The TouchPRO Wireless thermostat is shipped from the factory with the coin cell installed. To keep the battery from discharging during shipment and storage, the TouchPRO Wireless thermostat is shipped with a plastic tab inserted in the battery holder. This tab must be removed during installation. Simply pull the plastic tab out of the battery tray. Make sure that the battery tray is fully inserted into the TouchPRO Wireless thermostat.
Wiring
- Remove factory-installed jumper only for two-transformer systems
- Push excess wire back into the wall opening. Plug wall opening with non-flammable insulation
Terminal Designations
Wiring guide—heat pump systems 
Wiring guide—conventional systems
Verify battery function
- After receiving time and date from the TouchPRO Wireless thermostat, remove the thermostat from the wallplate.
- Wait 10 seconds and replace the thermostat.
- After a few seconds the thermostat should return to its normal display. If it does, you are done.
- Remove the battery tray, adjust the metal tabs for good contact and verify battery polarity.
- Re-install battery tray and repeat steps 1, 2 and 3.
- If battery function cannot be verified, replace battery. If thermostat does not return to its normal display, do not install the thermostat. Return it for evaluation.
Installer setup
| 0170 | System type | 1 | 1 heat/1 cool conventional |
| 2 | 1 heat/1 cool heat pump (no aux. heat) | ||
| 3 | Heat only (2-wire systems) | ||
| 4 | Heat only with fan | ||
| 5 | Hot water Series 20 system (power to open & close zone | ||
| valves/normally open zone valves) | |||
| 6 | Cool only | ||
| 7 | 2 heat/1 cool heat pump (with aux. heat) | ||
| 8 | 2 heat/2 cool multistage conventional | ||
| 9 | 2 heat/1 cool multistage conventional | ||
| 10 | 1 heat/2 cool multistage conventional | ||
| 11 | 2 heat/2 cool heat pump (no aux. heat) | ||
| 12 | 3 heat/2 cool heat pump (with aux. heat) | ||
| 0173 | Heat pump type | 0 | Air to air heat pump |
| 1 | Geothermal heat pump | ||
| 0180 | Fan control | 0 | Gas/Oil heat (equipment controls heating fan) |
| (heating) | 1 | Electric furnace (thermostat controls heating fan) | |
| 0190 | Changeover valve | 0 | O/B terminal controls valve in cooling |
| (O/B terminal) | 1 | O/B terminal controls valve in heating | |
| 0200 | Auxiliary Heat | 0 | Electric backup heat |
| 1 | Fossil fuel backup heat | ||
| 0210 | External Fossil Fuel | 0 | None |
| Kit | 1 | Yes | |
| 0220 | 1st Stage Cool/ Compressor cycle rate | 3 | Recommended for most compressors
[other options: 1, 2, 4, 5, or 6 CPH] |
| 0230 | 2nd Stage Cool/ Compressor cycle rate | 3 | Recommended for most compressors
[other options: 1, 2, 4, 5, or 6 CPH] |
| 0240 | First stage heat | 5 | Gas or oil furnaces of less than 90% efficiency |
| cycle rate (CPH= | 1 | Steam or gravity systems | |
| cycles per hour) | 3 | Hot water systems & furnaces of 90%+ efficiency | |
| 9 | Electric furnaces | ||
| [Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH] | |||
| 0250 | Second stage heat | 5 | Gas or oil furnaces of less than 90% efficiency |
| cycle rate (CPH) | 1 | Steam or gravity systems | |
| 3 | Hot water systems & furnaces of 90%+ efficiency | ||
| 9 | Electric furnaces | ||
| [Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH] | |||
| 0260 | Third stage heat | 9 | Electric auxilliary heat |
| cycle rate (CPH) | 1 | Steam or gravity systems | |
| 3 | Hot water systems & furnaces of 90%+ efficiency | ||
| 5 | Gas or oil furnaces of less than 90% efficiency | ||
| [Other options: 2, 4, 6, 7, 8, 10, 11, 12 CPH] | |||
| 0280 | Backlight | 0 | Backlight ON for approx. 8 seconds after keypress |
| 1 | Backlight always on low intensity, full bright after | ||
| keypress |
| 0300 | Manual/Auto | 1 | Automatic changeover (Heat/Cool/Auto/OFF) |
| changeover | 0 | Manual changeover (Heat/Cool/OFF) | |
| 0320 | Temperature | 0 | Fahrenheit ( ºF) |
| display | 1 | Celsius ( ºC) | |
| 0340 | Remote Temperature | 0 | None |
| Sensor | 1 | Outdoor for Display | |
| 2 | Outdoor for Control | ||
| 3 | Remote Indoor | ||
| 0345 | Dual Fuel Heat Pump | 0 | Balance point only |
| Control | 1 | Balance point + Failed to Maintain Heat protection | |
| 2 | Low lockout + High Lockout + Failed to Maintain | ||
| protection in between. | |||
| 0346 | Dual Fuel Heat Pump | 0 | Disabled |
| Upstage to Furnace | 0.5 | 0.5 hours | |
| Timer | 1 | 1 hour | |
| 1.5 | 1.5 hours | ||
| 2 | 2 hours | ||
| 3 | 3 hours | ||
| 4 | 4 hours | ||
| 5 | 5 hours | ||
| 6 | 6 hours | ||
| 8 | 8 hours | ||
| 10 | 10 hours | ||
| 12 | 12 hours | ||
| 14 | 14 hours | ||
| 16 | 16 hours | ||
| 0347 | Drop Temperature | 2 | 2 ºF 1.0 ºC |
| 3 | 3 ºF 1.5 ºC | ||
| 4 | 4 ºF 2.0 ºC | ||
| 5 | 5 ºF 2.5 ºC | ||
| 0350 | HP Compressor | 40 | 40 ºF 4.5 ºC |
| Lockout also Balance | 0 | None | |
| Point | 5 | 5 ºF -15.0 ºC | |
| 10 | 10 ºF -12.0 ºC | ||
| 15 | 15 ºF -9.5 ºC | ||
| 20 | 20 ºF -6.5 ºC | ||
| 25 | 25 ºF -4.0 ºC | ||
| 30 | 30 ºF -1.0 ºC | ||
| 35 | 35 ºF 1.5 ºC | ||
| 45 | 45 ºF 7.0 ºC | ||
| 50 | 50 ºF 10.0 ºC | ||
| 55 | 55 ºF 13.0 ºC | ||
| 60 | 60 ºF 15.5 ºC |
| 0360 | HP Aux Lockout | 40 | 40 ºF | 4.5 ºC |
| 0 | None | |||
| 5 | 5 ºF | -15.0 ºC | ||
| 10 | 10 ºF | -12.0 ºC | ||
| 15 | 15 ºF | -9.5 ºC | ||
| 20 | 20 ºF | -6.5 ºC | ||
| 25 | 25 ºF | -4.0 ºC | ||
| 30 | 30 ºF | -1.0 ºC | ||
| 35 | 35 ºF | 1.5 ºC | ||
| 45 | 45 ºF | 7.0 ºC | ||
| 50 | 50 ºF | 10.0 ºC | ||
| 55 | 55 ºF | 13.0 ºC | ||
| 60 | 60 ºF | 15.5 ºC | ||
| 65 | 65 ºF | 18.5 ºC | ||
| 0500 | Furnace Filter 1 | 0 | Disabled | |
| Change Reminder | 1 | 10 R.T. Day | ||
| 2 | 30 R.T. Day | |||
| 3 | 60 R.T. Day | |||
| 4 | 90 R.T. Day | |||
| 5 | 120 R.T. Day | |||
| 6 | 180 R.T. Day | |||
| 7 | 270 R.T. Day | |||
| 8 | 365 R.T. Day | |||
| 9 | 30 C Days | |||
| 10 | 60 C Days | |||
| 11 | 90 C Days | |||
| 12 | 120 C Days | |||
| 13 | 180 C Days | |||
| 14 | 365 C Days | |||
| 0502 | Furnace filter | 0 | Counts heat and cool | |
| reminder run time equipment counts | 1 | Counts cool only | ||
| 0510 | Humidifier Pad | 0 | Disabled | |
| Replacement | 1 | 90 C Days, 30 R.T. Days | ||
| Reminder | 2 | 180 C Days, 60 R.T. Days | ||
| 3 | 365 C Days, 90R.T. Days | |||
| 0520 | UV Lamp | 0 | Disabled | |
| Replacement | 1 | 365 Days | ||
| Reminder | 2 | 730 Days (2 years) | ||
| 0580 | Compressor protection | 5 | 5 minute compressor OFF time
[Other options: 0, 1, 2, 3 or 4-minute off time] |
|
| 0640 | Clock format | 12 | 12-hour time (i.e., “3:30 pm”) | |
| 24 | 24-hour time (i.e., “15:30”) | |||
| 0650 | Extended fan | 0 | OFF | |
| timer (heat) | 90 | Fan runs for 90 seconds after call for heat ends | ||
| 0660 | Extended fan | 0 | OFF | |
| timer (cool) | 90 | Fan runs for 90 seconds after call for cooling ends | ||
| 0670 | Keypad lock | 0 | Keypad unlocked (fully functional) | |
| 1 | Partially locked (access to temperature settings only) | |||
| 0680 | Heat temperature | 2 | Standard temperature control (recommended) |
| control | 1 | Choose if room is warmer than set temperature | |
| 3 | Choose if room does not reach set temperature | ||
| 0690 | Cool temperature | 2 | Standard temperature control (recommended) |
| control | 1 | Choose if room is cooler than set temperature | |
| 3 | Choose if room does not reach set temperature | ||
| 0700 | Temperature display offset | 0 | Thermostat displays actual room temperature
[Other options: -3 ºF, -2 ºF, -1 ºF, 1 ºF, 2 ºF, 3 ºF offset (-1.5 ºC, -1.0 ºC, -0.5 ºC, 0.5 ºC, 1.0 ºC, 1.5 ºC)] |
| 0710 | Reset | 0 | No reset |
| 1 | Reset HVAC installer options to factory default (only date | ||
| and time settings are retained) and remove from Lutron® | |||
| system | |||
| 0900* | Lutron System | 0 | Remove from Lutron system |
| Connection | 1 | Connected |
Installer system test
Adding the thermostat to a Lutron system
- Use the Lutron PC software to start activation mode. When a Lutron system is in activation mode, an unaddressed thermostat will show “Device Is Unaddressed” at the top of the screen.
- To activate thermostat press MORE. The thermostat will now show the connection screen and display “Press Connect” at the top of the screen.
- Press the CONNECT button. The CONNECT button will blink and the thermostat will display “Addressing” at the top of the screen.
- Return to the Lutron software and confirm thermostat activation. When activated, the thermostat will exit the connect screen and display “Device Is Addressed” at the top of the screen.
- The thermostat is now activated.
Special functions
Auto Changeover (Setup Function 0300): When set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature. Heat and cool settings must be at least 2 ºFapart.
Compressor Protection (Setup Function 0580): Forces the compressor to wait a few minutes before restarting, to prevent damage. During this time, the message “Wait” flashes on the display.
Accessories & replacement parts
- Please contact your distributor to order replacement parts.
- Cover plate*……………………………………………………. Honeywell Part Number 32003796-001
- Outdoor Temperature Sensor………………………… Honeywell Part Number C7089U1006
- Remote Indoor Temperature Sensor……………… Honeywell Part Number C7189U1005
- *(Use to cover marks left by old thermostats.)
Specifications
- Temperature Ranges
- Heat: 40 ºF to 90 ºF
- (4.5 ºC to 32.0 ºC)
- Cool: 50 ºF to 99 ºF
- (10.0 ºC to 37.0 ºC)
- Operating Ambient Temperature
- 0 ºF to 120 ºF (-18 ºC to 49 ºC)
- Shipping Temperature
- -30 ºF to 150 ºF (-34 ºC to 66 ºC)
- Operating Relative Humidity
- 5% to 90% (non-condensing)
- Physical Dimensions
- 4-15/16 in H x 6-9/16 in W x
- 1-7/16 in D
- (125 mm H x 166 mm W x 36 mm D)
Electrical Ratings
| W Heating | 20-30 V | 0.02-1.0 A |
| (Powerpile) | 750 mV | 100 mA DC |
| W2 Heating | 20-30 V | 0.02-0.6 A |
| Y Cooling | 20-30 V | 0.02-1.0 A |
| Y2 Cooling | 20-30 V | 0.02-0.6 A |
| Aux Auxiliary heat | 20-30 V | 0.02-1.0 A |
| O/B Changeover | 20-30 V | 0.02-0.6 A |
| E Emergency heat | 20-30 V | 0.02-1.0 A |
| L Heat pump reset | 20-30 V | 0.02-0.6 A |
Optional THP9045 Wiring Module
The THP9045 Wiring Module is designed to be used with applicable thermostats in 1 Heat/1 Cool retrofit applications where only 4 wires are available. The K terminal on the thermostat can be used to operate both the fan and compressor on a single wire, and the module is designed to receive the signal from the K terminal, split that signal and reroute it to operate the compressor, and/or fan for normal operation. See the THP9045 manual for further details.
Technical Assistance
- 24 hours a day, 7 days a week
- www.lutron.com
- U.S.A. / Canada: 1.800.523.9466
- Mexico: +1.888.235.2910
- Other Countries: +1.610.282.3800
Warranty: For warranty information, please see the Warranty enclosed with the product, or visit www.lutron.com/resiinfo
Technical Assistance
- 24 hours a day, 7 days a week
- www.lutron.com
- U.S.A. / Canada: 1.800.523.9466
- Mexico: +1.888.235.2910
- Other Countries: +1.610.282.3800
Lutron
- Lutron Electronics Co., Inc.
- 7200 Suter Road
- Coopersburg, PA 18036-1299
- USA
- TEL: +1.610.282.3800
- FAX: +1.610.282.1243
- www.lutron.com
Honeywell
- Honeywell International Inc.
- 1985 Douglas Drive North
- Golden Valley, MN 55422
- http://yourhome.honeywell.com
Reference
Download Manual:
Honeywell LR-HWLV-HVAC TouchPRO Wireless Thermostat Installation Guide
Honeywell LR-HWLV-HVAC TouchPRO Wireless Thermostat Installation Guide
Leave a Reply