Honeywell Home CT8602 PROGRAMMABLE THERMOSTAT OWNERS GUIDE

Total comfort temperature management with Smart Response Technology
Congratulations! You made a smart choice by purchasing your new Honeywell thermostat; the smart thermostat that:

Keeps you comfortable by automatically calculating exactly when the furnace or air conditioning should go on to have the house at the desired comfort temperature by the time you wake up or return home.
Saves the maximum amount of energy and money by automatically remembering to adjust the temperature when you leave home or go to sleep.
Provides the ultimate in comfort and convenience. It comes preprogrammed. You can use the preprogrammed schedule or set your own.
This manual answers many of the questions that can arise as you become familiar and comfortable with your
Honeywell thermostat the state-of-the-art in-home comfort control. Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.

MERCURY NOTICE
If this thermostat is replacing a control that contains mercury in a sealed tube, do not place your old control in the trash. Contact your local waste management authority for instructions regarding recycling and the proper disposal of this control, or of an old control containing mercury in a sealed tube.

TYPICAL LOCATION OF A MERCURY SWITCH IN A THERMOSTAT

Product Overview

STEP 1. PREPARE FOR INSTALLATION

Check the contents of your thermostat package to be sure all items are included.

Package Contents

Thermostat
Wallplate
Owners Guide
Wiring labels
Screws and anchors
! Locate the required tools to install your thermostat.

Tools Required

Screwdriver
Drill
Drill bits: 3/16 in. for drywall;
Hammer
Needle-nose pliers 7/32 in. for plaster

STEP 2. REMOVE OLD THERMOSTAT

Test your heating and cooling systems to make sure they work properly. If either system does not work, contact your local heating/air-conditioning dealer. To avoid compressor damage, do not operate the cooling system when the outdoor temperature is below 50°F (10°C).
Turn off power to the system at the furnace or the fuse/circuit breaker panel.
Carefully unpack your new thermostat and wallplate. Save package of screws, instructions, and receipt.
Remove the cover from the old thermostat. If the cover does not snap off when pulled firmly from the bottom, check for a screw or screws used to lock on the cover.
Loosen the screw or screws holding the thermostat to the wallplate and lift the thermostat away.
Disconnect the wires from the old thermostat. As you disconnect each wire, attach the enclosed labels with the old terminal designation. If there are only two wires, they do not need to be labeled. Wrap the wires around a pencil as shown to keep them from falling back into the wall.

Special Installations
Read this section if you are replacing:

Clock thermostat with separate wires for the clock.
Thermostat with six or more wires connected to it.
The thermostat in a heating-only system with three wires.

Replacing a Clock Thermostat that has C or C1 Clock Terminals
When replacing a Honeywell Chronotherm® Thermostat, you may find one or two wires going to the C or C1 clock terminals on the Chronotherm wiring wallplate. Do not allow them to touch, or you can damage the transformer. Disconnect the wires and wrap them separately using electrical tape. Do not wrap them together. Place the wires, where they will not interfere with the operation of the new thermostat. Record the colors and terminal designation labels of the remaining wires.
Replacing a Thermostat that has Six or More Wires
If there are six or more wires (excluding clock wires attached to terminals), you probably have a variation of a multistage heat pump or another multistage system. This thermostat is not compatible with multistage systems, so return the product to the place of purchase. For information about which programmable thermostats will work with your system, call Honeywell Customer Care at 1-800-468-1502.
Replacing a Thermostat that has Three Wires
If you have three wires for a heating-only system and can operate the fan using the fan On switch this thermostat works
with your system. However, some hot water (zoned) heating systems also have three wires. Your thermostat will work only if you install an isolating relay on these systems. For details, call your local heating and/or cooling contractor.STEP 3.

MOUNT THERMOSTAT WALLPLATE

Separate the wallplate from the thermostat by placing your thumbs between the bottom of the wallplate and the thermostat and pulling the wallplate up and away from the thermostat. See illustration.
position the wallplate on the wall. Level wallplate for appearance, if desired. Use a pencil to mark two mounting holes that best fit the application.
Remove the wallplate from the wall. Drill two 3/16 in. holes in the wall (if drywall) as shown. For plaster or wood, drill 7/32 in. holes as marked. Gently tap (provided) anchors into drilled holes until flush with the wall.
reposition wallplate over holes. Pull wires through the wiring opening. Loosely insert mounting screws into each of the holes.
Level wallplate, if desired. The thermostat functions correctly, even when not level.
Tighten mounting screws.

STEP 4. WIRE WALLPLATE TERMINALS

IMPORTANT
All wiring must comply with local codes and ordinances.
If unsure about household wiring procedures, call your local heating/air-conditioning contractor. Refer to the labels you placed on the wires when you removed the old thermostat (see illustration).

Match the letter of the old thermostat wire with the corresponding terminal letter on the new thermostat. Refer to Table 1.
Remove the factory-installed jumper connecting terminals R and RC if wires are connected to both of those terminals.
For wiring diagrams, if needed, see the Wiring Diagrams section.
Loosen terminal screws. Slip each wire beneath the matching terminal. Wraparound and straight connections are both acceptable, (see illustration). Tighten terminals.
Plug the hole in the wall with insulation to help prevent drafts from adversely affecting thermostat operation.

Table 1. Terminal Designations on Old and New Thermostats.

The terminal on Old Thermostat	Connect To	Description
R, RHA, 4, V	R	Power
Rc, R^a	Rc	Power for cooling
W, W₁, H	W	Heat
Y, Y₁, M	Y	Cooling
G, F	G	Fan
O	O	The changeover in cool. (Single-stage heat pump only).
Bb	Bb	The changeover in heat. (Single-stage heat pump only).
C^c, X^c, B^b	Do not connect.	Transformer common
W₂, H₂	Do not continue the installation. Call 1-800-468-1502.	Second stage heat.
Y₂	Do not continue the installation. Call 1-800-468-1502.	The second stage is cool.

if both RH and R terminals are present on the existing thermostat, remove the jumper and connect Rh to R and R to Rc.
Do not connect both O and B when wiring to a single-stage heat pump. Connect O to O. Tape off B.
Tape off end of the wire with electrical tape and push the taped wire back into the wiring hole in the wall.

STEP 5. INSTALL THE BATTERIES

IMPORTANT
Three fresh AA alkaline batteries must be installed for the programming and operation of the thermostat and the heating/ cooling system.

Install the batteries in the wallplate so the positive terminals all point up (see illustration).
If the thermostat is already mounted on the wall, remove the thermostat by placing your thumb between the thermostat and wallplate and pulling the thermostat up and away as shown on the next page.
When the batteries are running low, a REPL BAT message flashes for one to two months before the batteries run out completely. Replace the batteries as soon as possible once the message flashes.
IMPORTANT
Although the thermostat has a low battery indicator, replace the batteries once per year to prevent leakage and to prevent the thermostat and heating/cooling system from shutting down due to the lack of battery power in the thermostat.
If you insert new batteries within 20 to 30 seconds of removing the old batteries, the system retains the current time and day. If the display is blank, the batteries are dead or installed incorrectly. You must reset the time and day. Refer to Step 9. Set the Clock for instructions.
As a precaution when leaving home for longer than a month, change batteries before leaving to prevent the system from shutting down due to lack of power. Always use fresh alkaline batteries. Non alkaline batteries do not last as long and can leak, causing damage to the thermostat and the wall surface.

STEP 6. SET FAN OPERATION SWITCH

The thermostat fan operation switch, labeled FUEL SWITCH, is factory set in the F position. This is the correct setting for most systems. If your system is an electric heat system, set the switch to E. The E setting allows the fan to turn on immediately with the heating and cooling in a system where the G terminal is connected.

STEP 7. MOUNT THE THERMOSTAT

STEP 8. CUSTOMIZE YOUR THERMOSTAT

Your Honeywell CT8602 Thermostat comes preset to the most commonly used settings. The settings are:

Gas or oil forced air furnace.
Smart Response Technology on.
Temperature °F.
12-hour clock format.
You can change any or all of these settings.

IMPORTANT
Always press the keys with your fingertip or a similar blunt tool. Sharp instruments like pens and pencil points can damage the keyboard.

Press and hold down simultaneously until the display shows two numbers.
You now can change any of these settings.

System Type (Feature Number 4)
System type options are:

1 = Gravity or steam system.
3 = Hot water, high-efficiency furnace (90% or better), or single-stage heat pump.
6 = Gas or oil-forced air furnace (preset).
9 = Electric furnace.

To change your system type:

Press until the display shows your furnace or boiler type.
Press Time to move to the next feature or to return to the main display.

Smart Response Technology (Feature Number 13)
Smart Response Technology options are:

0 = Smart Response Technology on (preset).
1 = Smart Response Technology off.

To turn Smart Response Technology on or off:

Press once.
Press Time to move to the next feature or to return to the main display.
NOTE: See the Smart Response Technology section for information about this feature.

Temperature Format (Feature Number 14)
Temperature format options are:

0 = °F (preset).
1 = °C.

To change temperature format:

Pressonce.
Press Time to move to the next feature or to return to the main display.

Time Format (Feature Number 16)
Time format options are:

0 = 12-hour clock (preset).
1 = 24-hour clock.

To change time format:

Press once.
Press Time to move to next feature or to return to main display.

Heating Temperature Range Stops (Feature Number 34)
Temperature range options are:

90 = highest setting for heating setpoint (preset).
40 to 89 = temperature range (1°F increments) of heating setpoint settings.
Press or until the display shows the desired heating temperature range stop.
Press Time to move to next feature or to return to main display.

Cooling Temperature Range Stops (Feature Number 35)
Temperature range options are:

45 = lowest setting for cooling setpoint (preset)
46 to 99 = temperature range (1°F increments) of cooling setpoint settings.
Pressor until the display shows the desired cooling temperature range stop.
Press Time to move to next feature or to return to main display.

Factory Set Function (Feature Number 37)
Do not change this setting.

Press Time to move to next feature or to return to main display.

Furnace Air Filter Timer (Feature No. 43)
Filter timer options:

0 = off
1 = 30 days
2 = 90 days (preset)
3 = 180 days
4 = 365 days

To change your filter timer:

Pressuntil the display shows the desired number of days.
Press Time to move to next feature or to return to main display.
NOTE: The filter time is based on calendar days.

Humidifier Pad Timer (Feature No. 44)
Humidifier pad timer options:

0 = off (preset)
1 = 90 days
2 = 180 days
3 = 365 days

To change your humidifier pad timer:

Press until the display shows the desired number of days.
Press Time to move to next feature or to return to main display.
NOTE: The humidifier pad time is based on calendar days. See your humidifier instructions for complete details on replacing and/or cleaning your humidifier pad.

Ultraviolet (UV) Lamp Timer (Feature No. 45)
UV lamp timer options:

0 = off (preset)
1 = 365 days

To change your UV lamp timer:

Press until the display shows the desired number of days.
Press Time to move to next feature or to return to main display.
NOTE: The UV lamp time is based on calendar days. See your UV lamp instructions for complete details on replacing your UV lamps.

STEP 9. SET THE CLOCK

Set Current Day and Time
NOTE: On initial power-up, the screen flashes 1:00 pm until you press a key.

Press .
Press until the screen shows the current day.
Press Time until current time shows. (Tapping advances time in one-hour increments.)
Press until DST displays if daylight savings time is in effect.
Press .

STEP 10. PROGRAMMING

The keyboard is located behind the thermostat cover. The three most frequently used keys are near the display.
Pressing displays the current temperature settings. Pressing the keys to change the temperature. The thermostat displays day, time, program period, temperature, system and fan settings.
There is an individual key for each of the four program periods:

The program period when the house is at a comfortable temperature while you get ready for work or school. (This is a higher temperature during heating season and a lower temperature during cooling season.)
The program period you can set for an energy-saving temperature while you are away at work or school.
(This is a lower temperature during heating season and a higher temperature during cooling season.)
The program period when you want the house at a comfortable temperature for activities before bedtime.
(This is a higher temperature during heating season and a lower temperature during cooling season.)
The program period you can set for an energy-saving temperature while you are sleeping. (This is a lower temperature during heating season and a higher temperature during cooling season.)

Table 2. Default Temperature Settings.

eriod	Time	eating^a Temperature	Cooling Temperature
Wake	6:00 AM	70°F/21°C	78°F/25.5°C
Leave	8:00 AM	62°F/16.5°C	85°F/29.5°C
Return	6:00 PM	70°F/21°C	78°F/25.5°C
Sleep	10:00 PM	62°F/16.5°C	82°F/28°C

Your heating setpoints cannot be higher than 90°F (32°C) or lower than 40°F (4.5°C).
Your cooling setpoints cannot be higher than 99°F (37°C) or lower than 45°F (7°C).

Program the First Day

Start by programming the wake time and temperature for one day.

Press and release.
Press until the desired day displays (Mon, Tue, Wed, Thu, Fri, Sat, Sun).
Press time until the desired time shows in the display.
NOTE: Program times are in 15 minute intervals. For example, 8:00, 8:15, 8:30.
Pressor until the desired wake temperature displays.
The setpoint temperature range is 40°F to 90°F (4.5°C to 32°C) for heating and 45°F to 99°F (7°C to 37°C) for cooling.
Press to switch between setpoints.
NOTE: Program times are the same for heating and cooling.
Pressor until the display shows the desired temperature setpoint.
Press repeat these steps for each program period. The First Day is now programmed.
Repeat each step in Program the First Day for the rest of the week.
NOTE: After the first day is programmed, you can copy that day to any other day using the procedure in Copy a Day.
Press when the entire week is programmed.

Copy a Day
Your thermostat can copy program settings from one day to another.

Pressto enters programming mode.
Press until the display shows the day you want to copy.
Press .
Press until the display shows the day you want to copy to.
Pressto accepts the change.
Repeat these steps for each day you want to copy.
NOTE: donE appears for two seconds and then the normal program display appears.

Clear a Program Period
NOTE: Wake cannot be cleared.

Press for the program period you want to clear.
Press until the desired day displays.
Press and hold for approximately three seconds until time and temperature clear.
Repeat the above steps for each period to be cleared.
Press .

STEP 11. OPERATING YOUR THERMOSTAT

Change Temperature Setting Until the Next Program Period (Temporary Change)

Press or until the screen shows the desired temperature setting.
NOTE: The temporary temperature setting is displayed for about three seconds and then the room temperature is displayed. Temporarily appears in the display. The setting cancels when the next program period starts or when you press .

Change Temperature Setting Indefinitely (Hold)

Move the System switch to the desired position (Heat or Cool).
Press then or to change your setting if desired. (The display changes from showing the setpoint temperature to room temperature after approximately three seconds.)
To cancel Hold press.

Change the Temperature Setting Until a Designated Day and Period (Vacation Hold)

Press twice.
Pressor until display shows desired temperature setpoint.
Press Time until the desired number of days that you will be away (1 through 255) is displayed.
Press to select the program period when you want the program to restart.
NOTE: If Vacation Hold needs to be canceled before the designated time, press to return to the program.

Daylight Savings Time Key
This feature allows you to switch between standard time and daylight savings time.

Press during fall to set the time back one hour.
Press in spring to set time forward one hour. DST is displayed when operating on daylight savings time.
NOTE: Pressing Daylight Time key more than once in a five minute period scrolls through various time options.
(One hour earlier or later, with or without DST. Pressing the key six times in a five minute period returns you to the original setting.

View or Reset Timer Settings
When the thermostat activates a timer, the thermostat flashes Filter until you reset the timer.

Reset the timer by pressing the key until the expired timer is displayed.
Press the Time key to reset the timer.
Press the key.
NOTE: You can view the number of days remaining at any time by pressing thekey three or four times. If more than one timer is active, all active timers show sequentially when pressingthe key several times.

For complete instructions on replacing or cleaning your furnace filter, humidifier pad, or UV lamp, see the product owner’s manuals. Contact your local contractor or visit www.honeywell.com/yourhome.

STEP 12. SET THE FAN AND SYSTEM SWITCHES

First set Fan switch.

Fan On: The fan runs continuously. Use for improved air circulation or for more efficient central air cleaning. (In a heat-only system, fan runs continuously only if fan relay is connected to the G thermostat terminal.)
Fan Auto: Normal setting for most homes. The equipment controls the fan operation.

Then set System switch.

Heat: The thermostat controls your heating system.
Off: Both the heating and air conditioning systems are off.
Cool: The thermostat controls your air conditioning system.

IF YOU HAVE A PROBLEM

If…	Then.
Display does not appear.	• Make sure the batteries are fresh and installed correctly. • Make sure the thermostat is mounted and latched on the wallplate. Mount and latch the thermostat on the wallplate if it is not.
Temperature settings will not change (example cannot set the heating higher or the cooling lower).	• Make sure the temperature setpoints are: 40°F to 90°F (4.5°C to 32°C) for heating. 45°F to 99°F (7°C to 37°C) for cooling. • Check Customize Your Thermostat section, Feature Numbers 34 and 35. Reset as necessary.
Heating does not come on.	• Set the system switch to Heat. • Make sure heating setpoint is above room temperature. • Make sure circuit breaker is not tripped, and reset it if necessary. • Make sure power switch at equipment is in On position. • Wait five minutes for the system to respond.
Cooling does not come on.	• Set the system switch to Cool. • Make sure the cooling setpoint is below the room temperature. • Make sure the circuit breaker is not tripped, and reset it if necessary. • Make sure System switch at air conditioner is in On position. • Wait five minutes for the system to respond.
System on indicator( = heat, = cool) is lit, but no warm or cool air is coming from the registers.	Wait five minutes after seeing flame or snowflake and check registers again. If no hot or cool air is coming from registers, refer to Heating does not come on or Cooling does not come on. Or contact your local heating and cooling contractor.
Display flashes during programming.	The temperature setting limit was reached. Heating setting range is 40°F to 90°F (4.5°C to 32°C). Cooling setting range is 45°F to 99°F (7°C to 37°C).

If…

Then.

Temperature change occurs at the wrong times.

• Check the program times for the period in question.

• Make sure the AM and PM settings are correct.

• Make sure the current time and day settings are correct.

• Reprogram any incorrect settings.

NOTE: If your thermostat is set for Smart ResponseM technology, the start times occur before your programmed comfort periods.

Thermostat backlight appears dim.

• Wait until Replace Battery indicator is illuminated and replace batteries.

• Replace batteries now.

Toll-Free Customer Assistance
Please read and follow the instructions for this thermostat. If you have questions about this thermostat, visit our website at www.honeywell.com/yourhome, or call Honeywell Customer Care at 1-800-468-1502.

WIRING DIAGRAMS

Notice:
This thermostat is a Class B digital apparatus that complies with Canadian Radio Interference Regulations, CRC c. 1374.

Limited One-Year Warranty

Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time.
If the product is defective,

return it, with a bill of sale or other dated proof of purchase, to the retailer from which you purchased it, or
package it carefully, along with proof of purchase (including date of purchase) and a short description of the malfunction, and mail it, postage prepaid, to the following address:

Honeywell International Inc. USA Honeywell Canada:
Dock 4 MN10-3860 Honeywell Limited/Honeywell Limitée 1885 Douglas Drive North 35 Dynamic Drive
Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or the malfunction was caused by damage that occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Care, 1885 Douglas Drive North, Golden Valley, MN 55422-3992, or call 1-800-468-1502. In Canada, write Retail Products ON30 Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.

Automation and Control Solutions

Honeywell International Inc.
1985 Douglas Drive North Golden Valley, MN 55422
Honeywell Limited-Honeywell Limitée
35 Dynamic DriveScarborough, Ontario M1V 4Z9

www.honeywell.com/yourhome

REFERENCE:

Download Manual:

Honeywell Home CT8602 PROGRAMMABLE THERMOSTAT OWNERS GUIDE

other manuals:

Honeywell Home CT8602 PROGRAMMABLE THERMOSTAT Quick Installation GUIDE

Honeywell Home CT8602 PROGRAMMABLE THERMOSTAT OWNERS GUIDE

Honeywell Home CT8602 PROGRAMMABLE THERMOSTAT OWNERS GUIDE