Honeywell DT92E Wireless Room Thermostat Installation Manual

Honeywell DT92E Wireless Room Thermostat 

Installation

The DT92 wireless room thermostat comprises a DT92 Room Thermostat and a BDR91 Relay Box. These devices communicate on an 868MHz Radio Frequency (RF) band to control a single heating system component such as a boiler, pump or zone valve. RF communication is 2-way, allowing high performance energy efficient control, display of boiler information, and easy setup and communications check features.

Installation Notes

• The RF link between the Room Thermostat (DT92) and the Relay Box (BDR91) in Honeywell system packs is pre-configured at the factory and therefore should be installed at the same site.
• If products from individual system packs are separated, or mixed with other pre-configured system packs during installation, or a faulty unit is being replaced, the desired units must be specially configured to allow them to communicate with each other. This process is called Binding. Please refer to section 6) Binding / Rebinding Procedure.
• DT92 or BDR91 will not communicate with other RF products that use different frequencies or communications protocols.
• The DT92 room thermostat requires no power source other than the batteries provided.
• The BDR91 Relay Box requires a permanent 230V~ supply.
• The Relay Box should be installed before commencing the Room Thermostat installation

Installing the BDR91 Relay Box

• For best performance, install in an open space. Leave at least 30cm distance from any metal objects including wall boxes and boiler housing. Do not mount on metal wall boxes.
• EMC compliance considerations
• Keep AC mains supply/load cables separate from signal wiring.
• Refer to Code of Practice standards EN61000-5-1 and -2 for guidance

Installing the DT92 Room Thermostat

Power up

RF Communication Test

Locating the Room Thermostat

For best performance, install in an open space where DT92 can sense the room temperature, and where the signal strength is high. The Room Thermostat can be mounted on a wall or on the optional table stand. Leave at least 30cm distance from any metal objects and at least 1 metre from any other electrical equipment. Select the preferred location and test the Signal Strength before installation

Signal Strength Test

Mounting the Room Thermostat

Test & Binding Flow-chart

Basic System Operation

Automatic Operation

Temporary Manual Override

Loss of RF communications

Installer Mode 

To enter Installer Mode

To select a parameter

Display

To change a parameter

To exit Installer Mode

Parameter flowchart

Parameters

Description	Parameter	Range of values	Default
Minimum ON/OFF time Tempo minimo accesso	OT	1,2,3,4,5 m	1 m
Cycle rate	Cr	{3,6,9,12}	6
Proportional bandwidth	Pb	1.5 … 3.0 K	1.5K

Description	Parameter	Range of values	Default
Temperature measurement offset	tO	-3 … 3 K	0 K
temperature
Temperatur-Offset
Upper setpoint limit	uL	21 … 35 °C	35°C
consigne maximale
Limite superiore della temperatura
teplota
Lower setpoint limit	LL	5 … 21 °C	5°C
limite de consigne minimale
Temperatursollwertgrenze
lapel korlát
Najnižšia nameraná teplota
ECO temperature	ES	5 … 35 °C	18 °C
temperatuursinstelling
ECO deploy
Heat/cool changeover	HC	0 / 1	0
warmen/koelen Cambiamento Off setpoint adjust Room temperature sensor use Failsafe mode (loss of RF communications) Enable HR80 window-open function Enable HR80 local override Reset parameters	OS SuLC HO HL FS	0 = Disable / 1 = Enable– (= Off), 5…16°C 0 = DT92 sensor 1= HR80 sensor 2 = HR80 +DT92 sensor 0 = Off 1 = On 20% 0 / 1 0 = Disable / 1 = Enable Activado 0 = Disable / Disattivato i 1 = Enable /	0 = DT92 0 = Off 0  1 (factory)

Binding

The binding operation shown is required if:

•  any of the system components (Room Thermostat or Relay Box) are replaced
•  Relay Box has incorrect or no binding data stored (for example, when pre-bound system pack components have been mismatched).

Reset stored data in Relay Box

Put Relay Box into Binding Mode

Reset stored data in Room Thermostat

Put Room Thermostat into Binding Mode

Bind Room Thermostat to Relay Box

Now go to Section 3.2 RF Communication Test

Manufactured

Manufactured for and on behalf of the Environment and Combustion Controls Division of Honeywell Technologies Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle, Switzerland, by its Authorised Representative Honeywell Inc.

Reference

Download Manual:

Honeywell DT92E Wireless Room Thermostat Installation Manual

OTHER MANUALS:

Honeywell DT92E Wireless Room Thermostat User Guide

Honeywell DT92E Wireless Room Thermostat Installation Manual