Honeywell Home Red Link Wireless System with True ZONE Panel & Wireless Adapter System
Provides wireless control of HZ322 or HZ432 RedLINK TrueZONE Panels. (See zone panel information for heat/cool stage capacity. )
Installation guide for
- FocusPRO® wireless thermostats
- Wireless remote control
- Wireless outdoor air sensor
DISCONNECT POWER BEFORE BEGINNING INSTALLATION. Can cause electrical shock or equipment damage.
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not place the old control in the trash. Contact your local waste
management authority for instructions regarding recycling and proper disposal.
Must be installed by a trained, experienced technician
Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.
System installation at a glance
Installation procedure
This document covers linking and installation procedures for FocusPRO wireless thermostats and RedLINK accessories in TrueZONE applications. Before you begin, you must mount, wire & configure the TrueZONE panel and wireless adapter (see TrueZONE Installation Guide), then follow steps below.
You must configure the TrueZONE panel before you begin
- Install batteries in wireless devices……………………………… Page 3
- Link all devices to wireless network…………………………Pages 3-5
- Exit wireless setup……………………………………………………..Page 6
- Customize thermostat (installer setup)……………………Pages 6-10
- Mount thermostat and outdoor sensor………………………..Page 11
- To replace system components if needed, see page 13
If you have more than one TrueZONE Panel: Thermostats are linked to specific zone panels. Optional accessories must be linked to each zone panel separately.
Install batteries in wireless devices
When system wiring is complete and the TrueZONE panel is configured for RF, install batteries in all devices. Make sure batteries are inserted properly (see illustrations below).
Remote control (optional) Outdoor air sensor (optional)
Link all devices to a wireless network
Make sure the Connected light on the wireless adapter is flashing green. If the light stops flashing before you have linked all devices, press connects again. If the light does not flash, another EIM/wireless adapter may be in wireless setup mode. Exit wireless setup at the other EIM/wireless adapter
Link thermostats to a wireless network
- Press s or t to set a zone number for this thermostat (1 to 4), then press next.
- Press s or t to change the name or location of this zone, then press next.
- Example: 31 = Living room See complete zone list on page 8
- Press connect to establish a link to the wireless network.
- If E1 appears, see the error codes on page 12.
- After a brief pause, the confirmation screen at left should be displayed, to verify that the wireless connection has been established.
- Press did display the home screen
Link remote control to a wireless network (optional)
- Make sure the Connected light on the wireless adapter is flashing.
- Press connect at the remote. There will be a short delay as the remote seeks a signal from the wireless network.
- When the screen displays “Connected,” press done.
- Press no at the next screen to save and exit. (Or press yes and repeat steps 1-4 to link another zone panel.)If E1 appears, see the error codes on page 12.
The linking procedure may time out if there is no keypress within 30 minutes. To begin again, press and hold the blank space (or arrow if present) in the lower right corner of the screen until the display changes (about 3 seconds)
Link outdoor sensor to a wireless network (optional)
- Make sure the Connected light on the wireless adapter is flashing.
- Press the connect button on the back of the sensor.
- Check the thermostat to verify that the outdoor sensor is working. After about 15 seconds, the thermostat should display outdoor temperature and humidity. (If you are installing more than one zone of the panel, repeat steps 1-3 for each.)
Exit wireless setup
Press connect at the wireless adapter to exit the wireless setup (the light should stop flashing).
Note: The wireless adapter will automatically exit the wireless setup after 15 minutes of inactivity.
Note: If installing more than one zone panel, you must exit the wireless setup before installing an additional zone panel
Customize thermostat (installer setup)
Follow the steps below to begin the installer setup. At each function screen, press s or t to change the setting as desired, then press next to advance to the next function screen. See tables on pages 7-9 for a description of options for each function
Installer setup tables
Installer setup tables
Special functions
Adaptive Intelligent Recovery (Setup Function 13): Allows the thermostat to “learn” how long the furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the scheduled time. Compressor Protection (Setup Function 15): Forces the compressor to wait a few minutes before restarting, to prevent damage. During this time, “Heat On/Cool On” flashes on the display.
Comfort/Economy (Setup Function 26): If you choose Comfort, the auxiliary heat will respond quickly to meet the temperature setpoint. If you choose Economy, the system will wait longer. Auxiliary heat will be activated only if the setpoint is not reached within a reasonable time.
System test
Follow the procedure below to test for proper operation.
| 02 | Wireless test | 0 | Off |
| 1 | Test radio signal (after a brief pause, the screen displays 1-10 to show signal strength; 5 or higher is recommended) | ||
| 10 | Heating system | 0 | Heat and fan turn off |
| 1 | Heat turns on | ||
| 2 | Stage 2 heat turns on | ||
| 3 | Stage 3 heat turns on | ||
| 20 | Emergency | 0 | Heat and fan turn off |
| heating system | 1 | Heat and fan turn on | |
| 30 | Cooling system | 0 | The compressor and fan turn off |
| 1 | The compressor and fan turn on | ||
| 2 | Stage 2 compressor turns on | ||
| 40 | Fan system | 0 | Fan turns off |
| 1 | Fan turns on | ||
| 70 | Thermostat | 71 | Software revision number (major revisions) |
| information | 72 | Software revision number (minor revisions) | |
| (for reference only) | 73 | Configuration identification code (major) | |
| 74 | Configuration identification code (minor) | ||
| 75 | Production configuration date code (week) | ||
| 76 | Production configuration date code (year) |
CAUTION: EQUIPMENT DAMAGE HAZARD. Compressor protection (minimum off time)
is bypassed during testing. To prevent equipment damage, avoid cycling the compressor
quickly.
Mount thermostat & outdoor sensor
Outdoor sensor (optional)
To check the location before mounting: Restore the thermostat Home screen, then hold the sensor where you intend to install it and press the CONNECT button. If the sensor is working properly, the thermostat will switch to display outdoor temperature and humidity.
Verify proper setup
When the wireless setup is complete, make sure the Connected light on the wireless adapter is solid green (see below), then follow the steps in the Checkout section of the TrueZONE installation guide to verify proper operation.
Wireless status light
- Solid green: the wireless adapter is working properly and communicating with wireless devices.
- Flashing green: Linking to wireless devices (light flashes for 15 minutes after you press CONNECT).
- Solid red: Communication problem. Check wireless adapters and other wireless devices.
Error codes (thermostat & remote control)
If E1 appears during setup, check error code number (right side of screen):
- 29 Attempting to connect incompatible wireless devices.
- 30 Verify that the thermostat zone number matches number assigned at zone panel.
- 31 Verify that this zone number is configured at the zone panel as an RF thermostat.
- 34 Low signal strength. Move the wireless device to a different location and try again.
- 38 Make sure Connected light on wireless adapter is flashing and you are 2+ feet away from wireless adapter.
Replacing system components
Thermostat
To replace a thermostat, install batteries and follow the procedure on page 4 to link it to the wireless network. If necessary, modify settings as needed (see tables on pages 7-9)
Remote control & outdoor sensor
To replace a remote control or outdoor air sensor, install batteries and
follow the procedure on page 5 to link it to the wireless network.
TrueZONE panel & wireless adapter
After installing a new zone panel or wireless adapter, you must reset the thermostat and remote control to communicate with the new equipment, as described below.
At the thermostat:
- Press and hold the fan and s buttons for 3 seconds.
- Press back twice to display Function 39 (wireless setup).
- Press t to change the Function 39 setting to 0 (disconnect from old equipment).
- Follow the procedure on page 4 to link to new equipment.
At the remote control:- Press and hold the blank space (or arrow if present) in the lower right corner of the screen until the display changes (about 3 seconds).
- Press remove, then yes to disconnect from old equipment.
- Follow the procedure on page 5 to link to new equipment.
Specifications & replacement parts
Operating Ambient Temperature
- Thermostat: 32 to 120° F (0 to 48.9° C)
- Remote control: 32 to 120° F (0 to 48.9° C)
- Wireless Adapter: -40 to 165° F (-40 to 73.9° C)
- Outdoor air sensor: -40 to 140° F (-40 to 60° C)
Operating Relative Humidity
- Thermostat: 5% to 90% (non-condensing)
- Remote control: 5% to 90% (non-condensing)
- Wireless Adapter: 5% to 95% (non-condensing)
- Outdoor air sensor: 0% to 100% (condensing)
Physical Dimensions (height, width, depth)
- Thermostat: 3-9/16 x 5-13/16 x 1-1/2 inches (91 x 147 x 38 mm)
- Wireless Adapter: 5-9/16 x 4-3/8 x 1-1/4 inches (141 x 112 x 32 mm)
- Outdoor air sensor: 5 x 3-1/2 x 1-11/16 inches (127 x 89 x 43 mm)
Accessories & Replacement Parts
Item Part Number
- Wireless adapter THM4000R1000
- FocusPRO® wireless thermostat (programmable) TH6320R1004
- FocusPRO® wireless thermostat (non-programmable) TH5320R1002
- Remote control REM5000R1001
- Outdoor air sensor C7089R1013
- Battery holder 50007072-001
- Cover plate (covers marks left by old thermostats) 50002883-001
Regulatory information
FCC Compliance Statement (Part 15.19) (USA only)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Warning (Part 15.21) (USA only)
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement (Part 15.105 (b)) (USA only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- Wireless adapter, thermostats and outdoor sensor
To comply with FCC and Industry Canada RF exposure limits for general population/ uncontrolled exposure, the antenna(s) used for these transmitters must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
Remote control
This portable transmitter with its antenna complies with FCC and Industry Canada RF exposure limits for the general population/uncontrolled exposure. Section 7.1.5 of RSS-GEN
Operation is subject to the following two conditions
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
CAUTION: ELECTRONIC WASTE NOTICE
The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal of end-of-life equipment will help prevent negative consequences for the environment and human health.
Leave a Reply