Honeywell Home PRO 1000 Non-Programmable Thermostat
A quick reference to controls
Display screen
When “Heat On” or “Cool On” is flashing, compressor protection is engaged
Adjust the temperature
Need Help?
For assistance please visit:resideo.com
Built-in compressor protection
This feature helps prevent damage to the compressor in your air conditioning or heat pump system.
Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait 5 minutes before restarting. During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump model). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.
CAUTION
Equipment damage hazard
To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).
Battery replacement
Install two fresh AAA batteries when Lo Batt flashes on the screen. Lo Batt appears for 60 days before the batteries are depleted. Replace batteries once a year, or when you will be away for more than a month. The settings are stored in non-volatile (permanent) memory and are thus preserved when the thermostat is without batteries.
Electrical Ratings
System Voltage (50/60Hz) Running Current
- Heat (1st stage) 20-30 Vac 0.02-1.0 A
- (Powerpile) 750 mV DC 100 mA DC
- Auxiliary heat 20-30 Vac 0.02-1.0 A
- Cooling 20-30 Vac 0.02-1.0 A
In case of difficulty
If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.
| Display is blank | • Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is on. • Make sure furnace door is closed securely. • Make sure fresh AAA alkaline batteries are correctly installed. |
| The heating or cooling system does not respond | • Set the system switch to Heat. Make sure the temperature is set higher than the Inside temperature.
• Set the system switch to Cool. Make sure the temperature is set lower than the Inside temperature. • Wait 5 minutes for the system to respond. |
| Temperature
settings do not change |
Make sure heating and cooling temperatures are set to acceptable ranges:
• Heat: 40° to 90°F (4.5° to 32°C). • Cool: 50° to 99°F (10° to 37°C). |
| “Heat On” or “Cool On” is flashing | • Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor. |
| “Heat On” is not displayed | • Set the System switch to Heat, and set the temperature level above the current room temperature. |
| “Cool On” is not displayed | • Set the System switch to Cool, and set the temperature level below the current room temperature. |
Product Manuals
Search online for Resideo 69-2798EFS for the User Guide.
Resideo Technologies Inc. 1985 Douglas Drive North, Golden Valley, MN 55422
honeywellhome.com/support
33-00309EFS—05 M.S. Rev. www.resideo.com 07-20 | Printed in United States | Imprimé aux États-Unis | Impreso en EE. UU.
© 2020 Resideo Technologies, Inc. All rights reserved.
The Honeywell Home trademark is used under license from Honeywell International, Inc. This product is manufactured by Resideo Technologies, Inc. and its affiliates.
Este producto es fabricado por Resideo Technologies, Inc. y sus afiliados.
Reference
Download Manual:
Honeywell Home PRO 1000 Non-Programmable Thermostat Product Information Guide
OTHER MANUALS
Honeywell Home PRO 1000 Vertical Non-Programmable Thermostat Installation Guide
Honeywell Home PRO 1000 Non-Programmable Thermostat Operating Manual
Honeywell Home PRO 1000 Non-Programmable Thermostat User Manual
Honeywell Home PRO 1000 Non-Programmable Thermostat Product Information Guide
Leave a Reply