Hitachi SPX-WFG02 air Cloud Home Adapter THERMOSTAT
General Information
airCloud Home is an cloud-based solution for remotely controlling your Hitachi air conditioning system via smart phone. The airCloud Home Adapter SPX-WFG02 is used to connect your air conditioning system to Cloud through your W-iFi home router. Please read the guide and safety precautions before installing the Adapter. The installation is required to be performed by a professional. Please follow all of the instructions below carefully and keep the guide for the entire life of the Adapter. Any installation or use not foreseen by Johnson Controls-Hitachi Air Conditioning will be deemed noncompliant. This would invalidate the warranty and discharges Johnson Controls-Hitachi Air Conditioning of all liability, as does any failure to comply with the instructions given herein
General Safety Advice
- Do not try to open the housing of the Adapter. Avoid dropping or impact and Never immerse the Adapter in liquid.
- Do not use abrasive products or solvents to clean the housing of the Adapter. Its surface can be cleaned using a soft dry cloth.
- Do not use the Adapter outdoors. Do not route the connection cable outdoors.
- Any use or modification of the equipment not foreseen by Johnson Controls-Hitachi Air Conditioning could endanger users.
Packing List
Product Component Name
Installation Procedure
- Please reserve more than 40mm space in the lower part of the indoor unit as shown on figure (a).
- Remove the front cover of the air conditioning unit and the cover of the electric box. Refer to the air conditioner installation manual for instructions on removing the front cover and to open the electric box.
- The connecting cord supplied with the Adapter must be connected to the electronic board inside the electric box. Please pull the connecting cord from the connecting cord outlet as shown on figure(b), figure(c) and figure(d).
- Connect the connecting cord to the electric box as shown on figure (e). The connector on the electric board is usually marked as CN7. The position of CN7 connector may vary depending on the air conditioning model. Refer to the air conditioning system installation manual to confirm the connector number.
- Close the cover of the electric box, taking care not to trap the cable. Close the front cover of the air conditioning unit. Refer to the air conditioner installation manual for instructions on closing the electric box and closing the front cover
- Insert the hole side of the ②fixing clip into the groove of ①Adapter.
- Insert ②fixing clip and clamp to the right side lower cover of indoor unit please confirm the air conditioner installation manual on how to install the lower cover of indoor unit.
- Please confirm the air conditioner installation manual on how to install the lower cover of indoor unit.
Status Indicator (LED Indicator may light up while the air conditioner is turned off)
Initial Setting of App
Installation of App
- Go to Google Play or the Apple Store (depending on your smartphone) and download the “airCloud Home” Application.
- Please read and agree to “the Terms of Use” on the App.
- The App is free. Communication charges will be incurred for download and operation as per the local cell phone provider.
- Android is a trademark and registered by Google Inc.
- iPhone is a trademark and registered by Apple Inc.
- QR code is a trademark and registered by DENSO WAVE Inc.
Registration on App
- Click “Create Account”.
- Enter your name and click “Continue”.
- Enter your phone number and password (or click “E-mail” tab, and enter your E-mail address and password), read the “terms and condition” and check on the box, click “Continue”.
- Enter received verification code you received and click “Continue”.
- Click “Auto-Detect My Location” or Enter address details manually, and click “Finish”.
- The account has been created successfully.
Air Conditioner Registration and Router Connection
- Click “Add Air Conditioner” on the top screen after registration and login your App.
- Scan QR code on the bundled SSID&KEY label.
- Select “Connect using AP method”.
- If the SSID shown on the App is your home router, enter your home router password, click “OK”. Otherwise, click “Change Wireless Network”, select your home router enter password and click “OK”.
- press and hold the MODE button for 3 to 7 seconds until Link LED 2 flashes. The Link LED 2 keeps flashing till communication with the Wi-Fi router is succeeded
- Click “Change Wireless Network”, select the Wi-Fi access point of the Adapter with SSID printed on the bundled SSID&KEY Label, input password (the KEY). Click right arrow icon on the screen top to continue for connecting your smart phone with the Adapter.
- Waiting for the Adapter to connect to your home router. When communication is established, Link LED 1 turns on, Link LED 2 turns off.
- Your air conditioner has been successfully configured. You can reconnect your smart phone to your home router following the instruction of the App.
Restore Factory Setting
Reset the internal settings (restore the factory settings) by pressing and holding MODE button for 15 seconds. Please note that the configuration will be cleared and new pairing procedure will be required to use the Adapter. Please restore factory setting when discarding this Adapter.
- While the power light turns on, keep pressing MODE button until the LED flashes (about 15 seconds).
- Make sure all LEDs flash 4 times repeatedly.
- Only the power LED turns on after restoring factory setting succeed.
For Installers
- Make sure there is no dust on connection points such as the power terminals and/or on the cable. Risk of fire or electric shocks.
- Only use the cable supplied. It must not be altered. Risk of cable heating, resulting in a fire.
- Do not install the Adapter near devices that could be affected by radio waves.
- Do not allow children to touch the Adapter. Risk of injury.
- Do not install the Adapter in a location where devices using radio frequencies as a transmission medium are prohibited (refer to the applicable local standards).
- Do not install the Adapter in a location where there may be people with heart pacemakers
- Avoid installing the Adapter in an environment with high humidity (e.g. bathroom).
For Users
- Do not operate the air conditioner with ambient humidity above 80%.
- Water droplets may collect on the moving flaps and drip onto and damage equipment placed under the indoor unit. The damage may be worse if the problem is not detected during remote operations from App.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Make sure that the Air Conditioning unit is active during Wi-Fi communication operations.
- Abnormal operation may result in fire or electric shocks. Have the
- Adapter installed by a qualified installer
Technical Specifications
- ABS plastic housing.
- Configuration: AP and WPS.
- Operating temperature: 5°C to 35°C.
- Operating humidity: between 30% and 80%.
- index protection rating IP30.
- Pollution category: Class 2.
- Dimensions (l × w × h): 80 × 40 × 16.5 mm.
- Wireless LAN standard: IEEE 802.11b/g/n
- Security: WEP/WPA/WPA2/Open.
- the frequency used and maximum power used: 2.4000 GHz – 2.4845
- GHz/erp < 100 mW.
- wer supply: 12V 150mA DC.
- Integrated antenna.
Recycling
Do not dispose of the Adapter with the household waste. Please take it to a collection point or an approved center to ensure it is recycled.
Declaration of Conformity
Hereby, Johnson Controls-Hitachi Air Conditioning declares that the
radio equipment type 2 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.airdocumentation.com
Hitachi
- Europe importer: Johnson Controls Hitachi Air Conditioning Europe SAS
- Rue de Lombardie, Parc Aktiland II – 69800 Saint Priest, France
- Manufacturer: Johnson Controls-Hitachi Air Conditioning Wuhu Co., Ltd.
- No.2 Qiluoshan Road, Wuhu City, Anhui Province 241009, China
REFERENCE:
DOWNLOAD MANUALS:
Hitachi SPX-WFG02 airCloud Home Adapter THERMOSTAT Installation Guide
Hitachi SPX-WFG02 airCloud Home Adapter THERMOSTAT Installation Guide