Fantini cosmi Weekly Programmable Thermostats
Installation
WALL MOUNTING
Install the programmable thermostat at 1,5 meters above the floor level, far from kitchens, heat sources, windows and doors. Make sure the base is fixed to a level surface, without strains
ELECTRIC CONNECTIONS
Connect terminals 1 – 2 to the heating system with two wires thus replacing the traditional thermostat at any time and without adding further connections. When the ambient temperature increases, the relay will open terminals 1 – 2 and will close terminals 1-4. Terminal 4 is free and it may be used for signalling or other purposes, as required
OFF MODE SELECTION
When in OFF mode, Intellitherm may be set to keep a fixed temperature of 5°C to protect the system from the risk of freezing. This selection must be carried out during the installation and before inserting the batteries.
Note: if this selection is needed to be changed after the installation, Intellitherm has to be reset and reprogrammed.
MOUNTING THE THERMOSTAT BODY ON THE BASE
INSERTING AND REPLACING THE BATTERIES
Insert two long life AA 1,5V alkaline batteries, paying attention to the indicated polarity. Batteries last approximately 2 years: when they begin to run down, the battery symbol starts to flash on the display. If the batteries are not replaced within 15 days, Intellitherm C68 will switch-off automatically and the display will indicate OFF
TIME SETTING
(see the picture on the right)
PROGRAMMABLE THERMOSTAT
Display
Standard
Once the C68 is installed and connected, it is possible to use the weekly program with the pre-set operating time and temperatures, just positioning the switch on the A1 or A2 position.
Verify that the switch is in the HEATING position
Customization
Jolly Function
- With this function C68 enables you to cut out temporarily the automatic program at any time, without changing its settings, in order to have constantly the required temperature COMFORT – ECONOMY – OFF for a period from 1 to 240 hours
- With the switch in the A1 or A2 position, press the keys
to set for how many hours the C57RF has to cut the automatic program out, in order to force temporarily the temperature. The ring on the display will change the colour according to the selected temperature
- Once the set time is passed, C68 will resume the automatic program. To reduce or cut out the JOLLY period before the set time, press a different colour key than the one shown on the ring
Operating Hours
With C68 it is possible to know for how many hours the heating system worked the day before (closed relay – ON) and from the last Intellitherm initialization (last reset or battery insertion). The display will show the heating working hours, positioning the switches as indicated in the picture
Previous Day Minimum And Maximum Temperatures
- With Intellitherm C68 it is possible to verify the MINIMUM and MAXIMUM temperatures reached the day before and what time they were measured.
- Move the switch to the ECONOMY position to read the MINIMUM temperature or move to the COMFORT position to read the MAXIMUM temperature
- Move the switch to PROG
Summer / Air- Conditioning Mode
Intellitherm C68 starts the AIR-CONDITIONING mode moving the switch to the SUMMER position
The comfort temperature can be regulated setting the COMFORT/TMAX knob. The red sectors on the ring indicate what time the air-conditioning is ON; the other colours indicate when the system is OFF
Technical Data
- In compliance with EN 60730-1 and parts two.
- Contact rating 5 (3)A 250V c.a.
- Micro-disconnection (1BU).
- Software classe A.
- Voltage free switching contact.
- Temperature regulation: COMFORT from 16° to 34°C and ECONOMY from 5° to 23°C.
- Differential: +/- 0,25°C.
- Thermal gradient: 4°K/h.
- OFF mode with optional antifreeze protection (5°C) by a dip switch.
- Maximum room temperature: T45.
- double insulation.
- Protection degree IP20.
- Pollution degree 2.
- Impulse voltage 4000V.
- Power supply without connection to the electrical line with 2 AA 1,5V alkaline batteries (1 year battery life).
- Automatic control of the battery charge; the display will indicate if the charge is inadequate.
- Battery replacement without data dropout.
- Switch for the winter or summer operating modes.
- Reset the key to restore the set program.
- Dimensions 135 x 85 x 19 mm.
- ErP classification: ErP Class IV; 2% (EU Reg. 811/2013 – 813/2013)
REFERENCE:
DOWNLOAD MANUALS
Fantini cosmi C57 Weekly Programmable Thermostats INSTRUCTIONS Manual
OTHER MANUALS:
Fantini cosmi C57 Weekly Programmable Thermostats Technical Data Sheet
Fantini cosmi Weekly Programmable Thermostats INSTRUCTIONS Manual