Devireg 530 Electronic Thermostat
Applications and Functions
- The Devireg™ 530 series is a line of electronic thermostats used for control of indoor heating.
- The Devireg™ 530 is used for control of floor heating installations. The thermostat is equipped with a floor sensor for control of the desired floor temperature.
- The Devireg™ 531 is used for control of room heating installa-tions. The thermostat is equipped with a built-in air sensor for control of the desired room temperature.
- The Devireg™ 532 is used for room heating installations. The thermostat is equipped with a built-in room sensor and floor sensor. The room sensor is used for control of the room tem-perature. The floor sensor is used for maximum temperature limitation in wooden floors and other heat sensitive floors. The range of operation can be limited:
Maximum floor temperature setting
Maximum floor temperature is preset at the factory to 35°C for cable temperature safety.
Warning: Local building regulations must be observed when changing the maximum preset tempera ture.You can/must set the maximum floor tempera ture on the Devireg™ 532 by taking off the front cover and with a screwdriver adjust the sunken temperature dial in the top left hand corner between 20° to 50°C.
Notice:
The floor temperature is measured where the floor sensor is placed. The temperature of the bottom of a wooden floor can be up to 10 degrees higher than the top. Floor manufactures often specify the max. temperature on the surface of the floor.Please contact your floor supplier for maximum surface temperature.
Light indications (LED)
The Devireg™ 530 series has a LED indicator above the 2 pole safety switch (see illustration).
The LED has four indications:
- No light means the system is off.
- Red light means system is heating.
- Green light means system is standing by. floor sensor (only applicable for 530 and 532). Call your electrician.
Check connections, if they are OK, then disconnect the 2 sensor wires.
Measure the ohm value and check with the values in the table in Technical Specifications.
is used for setting the thermostat in frost protection mode, i.e. keeping the room/floor temperature (depending on type of thermostat) at approx. 5°C at any time.
Installation instructions
- When installing a thermostat from Devireg™ 530 series, you must first remove the front cover.
- To remove the front cover, gently press the release tabs under the bottom of the thermostat with a screwdriver. Then remove the front.
- You do not need to remove the set point dial.
Placement of Devireg™ 530, 531, and 532
- Installation height, typically between 80-150 cm for Devireg 531/532
- In wet rooms it should be installed on an even surface, according to local building regulations.
- At least 50 cm away from windows/doors that will be left open occasionally.
- Not on a wall where it will be subjected to direct sunlight.
- Not on the inner side of a wall facing the outside.
Configuration – Max. floor temp
Technical specifications for Devireg™ 530, 531, and 532
| Operation voltage | 180-250 VAC, 50/60 Hz |
| Standby consumption | Max. 0.25W |
| 3FMBZT:
t 3FTJTUJWF MPBE t *OEVDUJWF MPBE |
230V ~ 15A/3450W cos φ = 0.3 Max. 4A |
| Sensing unit | NTC 15 kOhm at 25°C |
| Sensing values: t 0¡$ t 20¡$ t 50¡$ |
42 kOhm 18 kOhm 6 kOhm |
| Hysteresis | +/- 0.4°C for 530 (528)
+/- 0,2 for 531 + 32 |
| Ambient temperature | -10° to +30°C |
| Frost protection | 5°C |
| Temperature range:
t 530 t 531 t 532 |
5-45°C 5-35°C 5-35°C, floor temperature limiter range: 20-50° C |
| Sensor failure monitoring | The thermostat has a built-in monitoring circuit, which will switch off the heating if the sensor is disconnected or short-circuited. |
| IP class | 31 |
| Dimensions | 85 mm x 85 mm |
The 2-Year DEVI Warranty
- You have purchased a DEVI heating system which we are sure will serve to improve the comfort and economy of your application.
- DEVI provides superior electrical heating solutions for total climate control in and around homes and buildings. DEVI offers a complete product program with DeviflexTM heating cables or DevimatTM heating mats, DeviregTM thermostats, DevifastTM fixing strips and Devi Self-limiting heating cables combined with additional products completing the product program.
- This 2 year warranty applies to all DEVI products.
- Should you, against all expectations, experience a problem with your DEVI product, you will find that DEVI offers a 2-year warranty from the date of purchase on the following conditions:
- During the warranty period, DEVI shall offer a new comparable product or repair the product in case the product is found to be faulty by reason of defective design, materials or workmanship. Repair or replacement shall be carried out at
discretion. DEVI shall not be liable for any consequential or incidental damages including, but not limited to, damages to property or extra utility expenses. - This warranty shall only be valid on the production of proof of purchase and must be submitted to the installer or seller without undue delay.
- An extension of the warranty period following repairs undertaken under warranty cannot be granted.
- The DEVI Warranty shall not cover any damage caused by incorrect conditions of use, incorrect installation or if installa-tion has been carried out by non-authorized electricians. All work will be invoiced in full if DEVI is required to inspect or repair faults that have arisen as a result of any of the above. The DEVI Warranty shall not extend to equipment that has not been paid in full.
- DEVI will, at all times, provide a rapid and effective response to all complaints and inquiries from our customers.
- The warranty explicitly excludes all claims exceeding the above conditions.
2-YEAR WARRANTY Warranty Certificate
The DEVITM Guarantee is granted to:
Attention:
The Warranty Certificate must be completed correctly for the Warranty to be valid.Please read the Warranty conditions on the previous page.
Address: DEVI A/S Ulvehavevej 61 DK-7100 Vejle
Tel: +45 74 88 85 00
Fax: +45 74 88 85 01
www.devi.com
Reference
Download Manual:
Devireg 530 Electronic Thermostat Installation Guide