Braeburn-5300-Universal-Thermostat-product

Braeburn 5300 Universal Thermostat Installation Guide

Braeburn-logo

Braeburn 5300 Universal Thermostat 

Braeburn-5300-Universal-Thermostat-product

Important Safety Information

WARNING

  • Always turn off power to the air conditioning or heating system prior to Installing, removing, cleaning or servicing thermostat.
  • This thermostat is a dual power thermostat and either requires 24 Volt AC Power or two (2) properly installed “AA” Alkaline batteries for normal operation and control of the heating or cooling system.
  • Properly installed batteries will allow the thermostat to retain clock settings in the event of loss of AC Power due to power outage or rolling blackouts when used as a hardwired thermostat.
  • This thermostat should only be used as described in this manual. Any other use is not recommended and will void the warranty.

Specification

  • Electrical Rating: 24 Volt AC (18-30 Volt AC)
    • 1 amp maximum load per terminal
    • 5 amp maximum load (all terminals)
  •  Control Range: 45º – 90º F (7º C – 32º C)
  • Accuracy: +/- 1º F (+/- .5º C)
  • AC Power: 18-30 Volt AC
  • DC Power: 3.0 Volt DC (2 “AA” Alkaline batteries included)
  • Compatibility: Compatible with low-voltage single-stage or multi-stage Heat / Cool systems, including heat pumps with up to three stages of heating and two stages of cooling, or conventional systems with up to two stages of heating and two stages of cooling. This thermostat can also be used on 250 to 750-millivolt heating-only systems.
  • Terminations: A, G, Rc, Rh, W2, B, O, Y1, Y2, W1/E/W3, C, L, S1, S2

Installation

Replacing Existing Thermostat

  • The cover, which may snap or hinge over the existing thermostat.
  • The electronics or body, which controls the existing system.
  • The sub-base, where the wires attach through the wall to the existing system.
  1. Always turn off power to the air conditioning and heating system prior to removing existing thermostat.
  2. Carefully remove the cover and electronics body from the old thermostat sub-base. Depending on the brand, these parts may pull off or need to be unscrewed. The old sub-base should remain wired and on the wall until steps 4 and 5.
  3. Label every old wire with the letter of the connection to which the wire is attached. Example letters are R, M, Y, etc. Depending on the brand of the old thermostat, your letters may be different.
    Old Terminal from Existing Thermostat New Terminal for New Thermostat (Model 5300)  

    Terminal Description

    A A External Air output
    G or F G Fan Control
    Rc Rc 24 Volt AC (Cooling for Dual Transformer Systems)
    R, V-VR or VR-R Rh 24 Volt AC
    W1, W2 or W-U W2 Stage 2 Heating
    B B Reversing Valve (Heating)
    O or R O Reversing Valve (Cooling)
    Y, Y1 or M Y1 Stage 1 Compressor
    Y2 Y2 Stage 2 Compressor
    W1/E/W3 W1/E/W3 1st Stage Heating for Conventional Systems or Emergency Heating for 3 Stage Heat Pumps
    C, X or B C 24 Volt AC, Transformer Common
    L or X L System Malfunction Indicator
    S1 S1 Optional Remote Sensor
    S2 S2 Optional Remote Sensor
  4. After labeling the old wires, loosen each connection and remove them from old sub-base. Secure the wires to prevent them from slipping into the opening in the wall.
  5. Remove the old sub-base from the wall, again being careful that the wires do not slip into the opening in the wall.
  6. Use the chart on page 1 to determine the new thermostat connections. As an example, if the old thermostat had a G or F connection, it goes to G on the new thermostat. It may be helpful to use the chart by circling (with a pencil or pen) the letter of each wire removed from the old thermostat.

NOTE: This thermostat is designed for use on low voltage 24-volt AC single-stage or multi-stage systems, including heat pumps with up to three stages of heating and two stages of cooling. Do not use this thermostat on systems with voltage higher than 30 Volts AC. This thermostat requires a transformer common wire for proper installation if used as a hardwired thermostat.

Installing New Thermostat

NOTE: When installing this thermostat in a new location, following a few simple guidelines and the applicable building codes will give the best results. Install the thermostat in a location that provides good airflow by avoiding areas behind doors, near corners, air vents, direct sunlight or heat-generating devices. The wiring must conform to all building codes and ordinances as required by local and national code authorities having jurisdiction for this installation.

  1. Always turn off the power to the air conditioning and heating system prior to installing this thermostat.
  2. Locate the release latch on the bottom (not the back) of the thermostat. Press the release latch in and separate the body from the sub-base of the thermostat. Because this thermostat has 14 possible connection points, you may need to apply moderate force to separate the parts.
  3. Set the thermostat electronics and cover down on a clean surface. Place the sub-base on the wall in the desired location.
  4. Using the slotted mounting holes in the sub-base, mark the placement of the mounting holes through the slots and onto the wall. Ensure the wires come out of the wall into the center hole of the sub-base.
  5. After verifying the drill will not damage items in the wall, use a 3/16 drill to create the mounting holes. Gently tap the supplied plastic anchors into the holes in the wall.
  6. Place the thermostat sub-base against the wall in the desired location. Ensure the thermostat is level, the wires are inserted in the opening, and the mounting holes are aligned with the slots on the sub-base.
  7. Fasten sub-base to wall using supplied screws into the plastic wall anchors.
  8. Connect wires to the quick wiring terminal blocks. Use the wiring diagram chart to ensure the old and new connections are correct.
  9. To prevent electrical shorts and potential damage to the thermostat, make sure all wire connections are secure and not touching each other.
  10. Locate the thermostat body, and ensure the cover is still installed properly. Using the mounting tabs on the top of the sub-base as a guide or hinge, close up the thermostat case by pivoting the body and cover closed. The latch on the bottom of the thermostat will click when the case is properly closed. Because this thermostat has 14 possible connection points, you may need to apply moderate force to close the case.
  11. Flip the front thermostat cover up and open the battery compartment door.
  12. Locate the positive [+] ends of the batteries and match them with the positive [+] terminals located in the battery compartment. Install the two new “AA” alkaline batteries (supplied). Close battery compartment door.
  13. Restore system power and proceed to programming and system checkout.

Quick Reference

Braeburn-5300-Universal-Thermostat-fig.1

  1. SYSTEM Button: Selects AUTO (Heat/Cool), COOL, OFF, HEAT or EMER.
  2. PROG Button: Press to enter the program setup mode where you can select the time, temperature and fan setting for each program period. Scrolls backwards between user/installer setup screens.
  3. HOLD Button: Enables or disables extended hold mode or temporary program override.
  4. RETURN Button: Press and hold for 4 seconds to enter the user settings mode (see user manual). Scrolls between user/installer setup screens. Returns unit to normal mode when in program mode.
  5. DAY/TIME Button: Enters time and day setting mode. Selects individual days in program mode.
  6. FAN Button: Selects AUTO, ON, CIRC (recirculate) and PROG (program) modes.
  7. RESET Button: Resets time, program and some user settings back to the factory default. See section 4 for a list of functions that will return to their factory default settings after the RESET button is pressed.
  8. Button: Turns on backlight for 10 seconds.
  9. Button: Increases setting (time, temperature, etc.). Scrolls between option settings.
  10. Button: Decreases setting (time, temperature, etc.). Scrolls between option settings.
  11. RETURN and Buttons: Press both buttons at the same time and hold for 4 seconds to enter the installer settings mode (see section 4).
  12. RETURN and PROG Buttons: Press both buttons at the same time to exit the installer settings mode.
  13. PROG and HOLD Buttons: Press and hold both buttons at the same time to view the outdoor temperature if an outdoor sensor is connected.
  14. CLEAR Button: Located on the back of the thermostat. Resets the thermostat to all factory default settings. See section 4 for a complete list of settings.

Programming Installer Settings

Status After CLEAR–Factory Default Settings
At initial power up or after Installer CLEAR is pressed, the thermostat is reset to factory defaults. Installer CLEAR is located on the circuit board.

Function Status After CLEAR
Operation mode OFF, Auto Changeover enabled
Temperature hold Permanent and temporary hold cleared
Fan Switch AUTO
Clock 12:00 pm, Monday
Room temperature Display 70° F (21.0° C), to be renewed within 5 seconds
Set point temperature 62° F (17.0° C) for Heat and Emergency Heat 83° F (28.0° C) for Cool
Temperature scale Fahrenheit
Operating program DAY program, Monday
Low-battery warning Off, to be renewed within 5 seconds
AC interrupted warning Off, to be renewed within 5 seconds
1st stage differential 0.2° F (0.1° C)
2nd stage differential 2° F (1.0° C)
3rd stage differential 2° F (1.0° C)
Programming 7 Day, 4 Event
Deadband 3° F
Residual Cooling Fan Delay 60 seconds
Short cycle protection timer On, 5 minutes, Reset
Adaptive Recovery Mode OFF
Output relays All turned off
Recirculating Fan Timer reset, with 24 min OFF, 12 min ON, Lock OFF
Extended Hold Long (indefinite)
Filter Check Monitor 0 days-No Warning, Timer reset
Keypad Lock Complete (level 2)
System type Conventional, Single Stage
1st Stage Heat Fan Control Gas
2nd Stage Heat Fan Control Electric
Fossil Fuel Compressor Lock Off
Auto Changeover Enabled
Compressor Outage Protection Off, Timer reset
Temperature Sensor Internal
12 / 24 Hour Clock 12 hour
Adjustment Limit from Set Point 0, OFF
AC Interrupt Warning Mode OFF
User Profile Residential
Compressor Balance Point 0 deg – No Lockout
Function Status After CLEAR
Auxiliary Balance Point 0 deg – No Lockout
Economizer Control None – Disabled
UV Monitor 0 days – No Warning, Timer reset
Humidifier Pad Monitor 0 days – No Warning, Timer reset
Heat Limit 90 deg – No Limit
Cool Limit 45 deg – No Limit
Maximum Override Duration 4 hours

Status After RESET–Factory Default Settings

When the User RESET button is pressed, the following options will reset to the factory defaults. All other settings are saved when the RESET button is pressed.

Function Status After RESET
Programming Default setting depending on programming mode setting (see User Manual). For manual mode: Heat – 62° F, Cool – 83° F.
Clock 12:00 pm, Monday
1st stage differential 0.2° F (0.1° C)
2nd stage differential 2° F (1.0° C)
3rd stage differential 2° F (1.0° C)
Filter, UV and Humidity Pad Check Monitor  

0 days-No Warning, Timer reset

Adjustment Limit from Set Point 0, OFF
Temperature Hold Permanent and temporary hold cleared, reset to Long Hold
Short Cycle Timer Reset
Recirculating Fan Timer reset, 24 minute off cycle. With recirculating lock set, fan state defaults to CIRC.
Maximum Temporary Override Duration  

4 hours

Setting Thermostat Installer Options

The Installer Options section allows the system and programming parameters to be set up at installation. The Installer Options mode is menu driven. As the different options are programmed you may eliminate specific options. For example, if the system is set to a single-stage heat pump, Option 8, selecting the AUX stage fan control will no longer be available.
The Installer Option mode is entered by holding the RETURN and buttons together for 3 seconds. Installer Option 1 (Residential or Commercial) will be displayed. Pressing the or buttons will scroll between choices. To scroll to the next installer option, press the RETURN button. To scroll backward between installer options, press the PROG button. The thermostat will return to normal operating mode by pressing the RETURN and PROG buttons at the same time.
NOTE: The thermostat will return to normal operating mode automatically after 30 seconds if no buttons are pressed.
NOTE: Any changes to Installer Option 6 (System Type) will cause Options 7, 8, 9, 10, and 11 to reset to the default values that are dependent on system selection.
NOTE: Any changes to Installer Options 1 through 6 will cause all User Options and Programming to reset to their default values if the User Options were previously programmed. See User Manual, Section 2.

Braeburn-5300-Universal-Thermostat-fig.6 Braeburn-5300-Universal-Thermostat-fig.7 Braeburn-5300-Universal-Thermostat-fig.8 Braeburn-5300-Universal-Thermostat-fig.9Braeburn-5300-Universal-Thermostat-fig.10

  1. Selects a Residential or Commercial (BUS) profile. Determines programming events per day. If Residential is selected, 4 events per day are available. If Commercial is selected, 2 events per day are available. Only the 7 day programmable mode is available for the Commercial profile.
  2. Selects the programming mode, either full 7 days or 5-2 day (weekday weekend) programming or non-programmable. If the Commercial profile was selected in step 1 this option is not available.
  3. Selects either a 12-hour or 24-hour clock.
  4. Selects a preferred temperature scale of either ºF or ºC.
  5. Selects Auto Changeover on or off. When off is selected, the AUTO icon will not be displayed when selecting the system options with the system button. When Auto Changeover mode is enabled and selected, the system automatically switches between heating and cooling when the room temperature meets the programmed heating or cooling set points.
  6. Selects single-stage conventional (11C), 2-stage conventional (22C), single-stage heat pump (11HP), 2-stage heat pump (22HP), or 3-stage heat pump (32HP). Any change made to the system type resets Installer Options 7 through 11 to their default values depending on the system selected.
  7. Selects between 1st stage gas or electric heat Fan Control. This Installer Option is not available with a heat pump system.
  8. Selects aux-stage gas or electric heat Fan Control. This Installer Option is only available with a 2 or 3-stage heat pump system.
  9. For heat pump units with an electric auxiliary stage, both the first and second stages of heating will run when a call for second-stage heat is made. For heat pump units with a fossil fuel auxiliary stage, the compressor stage(s) will be locked out one minute after a second stage heat call, and the second stage will only be used.
    NOTE: Can be overridden by auxiliary balance point. See item 20 on page 10 for details.
  10. Select between turning the AC power interrupt warning off or on. During a power loss when batteries are installed, the thermostat will display an outage warning. The system clock will continue to run, and all settings will be maintained until the outage period is over. This Installer Option is only available when the thermostat is installed as a hardwired unit.
  11. This thermostat provides cold weather compressor protection by locking out the compressor stage (1st stage) of heating for a period of time after a power outage greater than 60 minutes. The lockout period is one hour less than the outage time, up to a maximum of 12 hours. During that period of time, the auxiliary heat stage will still be available to maintain the set point temperature. The compressor lockout can be disabled by setting this option to OFF
  12. This thermostat includes an automatic compressor protection feature to avoid potential damage to the cooling system from short cycling. This thermostat automatically provides an adjustable delay after turning off the cooling system output to protect the compressor. This protection is also present in the heat mode of operation on single-stage heat pump systems to protect the compressor.
  13. During the COOL mode of normal operation, the fan will stay on for 60 seconds after the cooling system has satisfied the set point temperature and has turned off the compressor. This allows the system to provide higher efficiency during cooling operations.The delay is selectable between 0, 30, 60 or 90 seconds.
  14. The Recirculating Fan can be “locked on”, so that the only fan selections available to the user are CIRC and ON. The Recirculating Fan Mode provides more even temperature distribution and improves indoor air quality by circulating air through the furnace filtration system more often. By locking the Recirculating Fan on, the user will only have the option to run the fan all the time (ON) or use the Recirculating Fan Feature (CIRC). If the Recirculating Fan lock is set to off, the thermostat is put into the Recirculating Fan Mode by pressing the FAN button until the CIRC icon is displayed. If no call for heating or cooling occurs within the fan off cycle set in the User Options (see User Manual), the fan will run for 12 minutes. When the fan lock is set to on, the highest setting, 120 minutes, will run the fan least often – 9% minimum running time. The lowest setting, 24 minutes (factory default), will run the fan most often – 33% minimum running time. The Recirculating Fan feature is available in the COOL, OFF, HEAT, or EMER modes.
    Fan Cycle Setting Fan Off Time (minutes) Fan Run Time (minutes)
    24 24 12
    40 40 12
    60 60 12
    120 120 12
  15. Enables or disables the ARM™ feature. During ARM™, room temperature is recovered gradually by turning on the heating or cooling before the end of the setback period. In a multi-stage configuration, room temperature is recovered gradually by using only the first stage heating or cooling until the last 20 minutes, to minimize the use of the 2nd stage heating or cooling. The set point temperature is changed to that of the upcoming comfort program temperature. The start time of recovery is based on the difference between the current room temperature and the upcoming comfort program set point temperature. ARM™ does not operate when the unit is in the temporary or permanent HOLD mode or if the program is temporarily overridden or if emergency heat is selected for multi-stage heat pumps. If the ARM™ feature is disabled the thermostat will recover the set point temperature at the programmed set point time after the setback period ends.
  16. If a Braeburn® indoor or outdoor remote sensor is connected during installation, the thermostat will automatically detect the type of sensor. When an indoor sensor is detected, you may select between internal (sensI), external (sensE), or averaging (sensA) for temperature control. When an outdoor sensor is automatically detected, the thermostat will remove the choices for indoor sensing from the menu and enable outdoor measurement. The outdoor sensor may be used to determine if balance points have been exceeded, and outdoor temperature display. For proper auto-detection, you must use a Braeburn brand external sensor. Should the external sensor become unwired, the thermostat will retain the settings, but the balance points, and outdoor temperature display will be disabled until the external sensor is repaired. Test the operation of the external sensor by pressing the PROG and HOLD buttons at the same time.
    Option Setting Temperature Control Balance Points and Outdoor Display
    sens I (Internal Thermostat Sensor) At Thermostat N/A
    sens E (External Remote Indoor Sensor) At Remote Sensor N/A
    sens A (Internal and Remote) Average between Internal and Remote N/A
  17. The keypad lockout feature has two levels of security. Level one locks all buttons (including the reset) except for the , and backlight buttons. Level 2 locks the entire keypad except the backlight button. The and buttons can be pressed together to enter the lock code but the buttons do not work individually to adjust the temperature. The lock level is set during the Installer Options and the lock code is set in the User Options. See the User Manual, Section 2.
  18. When Auto Changeover mode is enabled and selected, the system automatically switches between heating and cooling when the room temperature meets the normal criteria for either a heating or cooling call. There is a forced separation (dead band) between the heating and cooling set points, so the systems do not work against each other. This option selects Auto Changeover Dead Band of 2º, 3º, 4º or 5º F. The default is 3º F.
  19. Only available with multi-stage heat pump and outdoor sensor connected. Locks out the use of the compressor heat stage for outside air temperatures less than installer setting. Select from no lockout or a setting between 10º F to 50º F (-9º C to 10º C).
  20. Only available with multi-stage heat pump and outdoor sensor connected. Locks out the use of the auxiliary heat stage for outside air temperatures over installer setting. Select from no lockout or a setting between 70º F to 40º F (21º C to 4º C). NOTE: This balance point overrides the fossil fuel compressor lockout. If the lockout is set to AG and the outdoor temperature is over the AUX balance point, the compressor will remain on during a second stage call. The unit will recover to the set point without the AUX stage.
  21. Selects Outside Air Intake Options. Scroll between none (disabled), economizer mode and time of day mode. Enables the operation of an outside air damper system in either the economizer mode or time of day mode. Available only in commercial (BUS) mode.
    Time Step / Override Cooling Call External Air Output (A)
    Economizer Mode Time of Day Mode Disabled
    Occupied YES or NO ON ON OFF
    Unoccupied YES ON OFF OFF
    NO OFF OFF OFF
    Override YES or NO ON ON OFF
  22. Selects the heating set point upper limit, scrolls between 90º F and 60º F (32º C and 10º C).
    Time Step / Override Heating Call External Air Output (A)
    Economizer Mode Time of Day Mode Disabled
    Occupied YES or NO ON ON OFF
    Unoccupied YES OFF OFF OFF
    NO OFF OFF OFF
    Override YES or NO ON ON OFF
  23. Selects the cooling set point lower limit, scrolls between 45º F and 80º F (7º C and 27º C).

Testing the Thermostat

WARNING! Read BEFORE Testing

  • Do not short (or jumper) across terminals on the gas valve or at the heating or cooling system control board to test the thermostat installation. This could damage the thermostat and void the warranty.
  • do not select COOLING test modes if the outside temperature is below 50° F (10° C). Doing so could possibly damage the compressor system and may cause personal injury.
  • This thermostat includes an automatic compressor protection feature that is DISABLED during test mode. When testing, DO NOT quickly switch the compressor on, off and on. Doing so could possible damage the compressor and may cause personal injury.
    This thermostat features a menu-driven operational test mode. This test mode is intended for use by trained HVAC technicians. If you are unfamiliar with the operation of this equipment, please contact a qualified service technician to perform these tests.
  • To START TEST MODE, Press PROG and at the same time for 3 seconds.
  • To NAVIGATE TEST MODE, Press RETURN to move forward to the next test type.
  • tO RUN THE TEST, press to start or stop the test.
  • To EXIT TEST MODE, Press PROG and RETURN at the same time for 3 seconds.
Test Type System Function System Type Active Terminals
Cooling 1st Cooling Stage Conventional or Heat Pump Y1, O, G
Cooling 2nd Cooling Stage Conventional or Heat Pump Y1, Y2, O, G
Heating 1st Heating Stage Conventional W1, B, G*
Heating 1st Heating Stage Heat Pump Y1, B, G
Heating 2nd Heating Stage Conventional W1, W2, B, G*
Heating 2nd Heating Stage 2 Stage Heat Pump Y1, W2, B, G
Heating 2nd Heating Stage 3 Stage Heat Pump Y1, Y2, B, G
Heating 3rd Heating Stage 3 Stage Heat Pump Y1, Y2, W3, B, G
Heating Emergency Heat 2 or 3 Stage Heat Pump E, B, G*
Fan Fan Only Conventional or Heat Pump G
Econ Economizer Business A

To provide time to verify equipment operation, a test will run for 5 minutes. At the end of that time, the thermostat will return to normal operating mode. To stop a test early press PROG and RETURN at the same time for 3 seconds.
NOTE: Only tests that apply to the current thermostat settings will be displayed. As an example, tests for 3rd stage heating will not be available on a thermostat configured for a 2 stage conventional system.
*Notes on Fan (G Terminal) Function: The G terminal will only be active if the stages are configured as electric heat. Systems that have the heating stages configured as gas will not activate the fan (G) terminal.

Wiring Diagrams

Braeburn-5300-Universal-Thermostat-fig.2

NOTES:

  1. Transformer Common connection not required for battery-only operation of thermostat.
  2. Second Stage Control connections not used for single stage heating or cooling systems.
  3. Remote Sensor Terminals can be either for Outdoor or Indoor Remote Sensor.
  4. For millivolt or other 2 wire heating systems, connect wires from heating control to Rh and W1.

Braeburn-5300-Universal-Thermostat-fig.3

NOTES:

  1. Transformer Common connection not required for battery-only operation of thermostat.
  2. Second Stage Control connections not used for single stage heating or cooling systems.
  3. Remote Sensor Terminals can be either for Outdoor or Indoor Remote Sensor.
  4. For millivolt or other 2 wire heating systems, connect wires from heating control to Rh and W1.

Braeburn-5300-Universal-Thermostat-fig.4

NOTES:

  1.  Transformer Common connection not required for battery-only operation of thermostat.
  2. Second Stage Control connections not used for single stage heating or cooling systems.
  3. For units requiring reversing valve to be energized during heating, connect reversing valve to B terminal. For units requiring reversing valve to be energized during cooling, connect reversing valve to O terminal.
  4. Required for units with 2 stage heat only.
  5. For 2 stage heat units not having a separate Emergency Heat Terminal, add installer supplied jumper.
  6. Remote Sensor Terminals can be either for Outdoor or Indoor Remote Sensor.
  7. If L Terminal is used, 24VAC common (C terminal) must be connected.

Braeburn-5300-Universal-Thermostat-fig.5

NOTES:

  1. Transformer Common connection not required for the battery-only operation of the thermostat.
  2. For units requiring reversing valve to be energized during heating, connect reversing valve to the B terminal. For units requiring reversing valve to be energized during cooling, connect reversing valve to O terminal.
  3. Remote Sensor Terminals can be either for Outdoor or Indoor Remote sensors.
  4. If L Terminal is used, 24VAC common (C terminal) must be connected.

Warranty

Store this booklet for future reference
Braeburn Systems LLC, as an Energy Star partner, has determined that this product meets the Energy Star Guidelines developed by the U.S. Environmental
Protection Agency & the U.S. Department of Energy for maximum energy efficiency.
©2009 Braeburn Systems LLC • All Rights Reserved.
U.S. Patents D525,154; D531,528; 7,156,317; 7,438,469 • Made in China • No. 5300-100-008
Braeburn Systems LLC warrants each new Braeburn thermostat against any defects that are due to faulty material or workmanship for a period of five years after the original date of purchase by a professional service technician. This warranty and our liability does not apply to batteries, nor does it include damage to merchandise or the thermostat resulting from accident, alteration, neglect, misuse, improper installation or any other failure to follow Braeburn installation and operating instructions.
Braeburn Systems LLC agrees to repair or replace at its option any Braeburn thermostat under warranty provided it is returned postage prepaid to our warranty facility in a padded carton within the warranty period, with proof of the original date of purchase and a brief description of the malfunction. This limited warranty does not include the cost of removal or re-installation.
This warranty gives you specific legal rights and you may also have other rights that vary from state to state or province to province. Answers to any questions regarding our limited warranty may be obtained by writing our corporate offices.
Braeburn Systems LLC
2215 Cornell Avenue • Montgomery, IL 60538
Technical Assistance: www.braeburnonline.com
Call us toll-free: 866-268-5599 (U.S.)
630-844-1968 (Outside the U.S.)
WARRANTY FACILITY: Braeburn Systems LLC
Attn: Warranty Department
2215 Cornell Avenue Montgomery, IL 60538

REFERENCE

Download Manual

Braeburn 5300 Universal Thermostat Installation Guide

other manuals

Braeburn 5300 Universal Thermostat User Manual

Braeburn-logo

Braeburn 5300 Universal Thermostat Installation Guide


Posted

in

by

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *