DANFOSS LX205T TOUCH SCREEN PROGRAMMABLE THERMOSTAT Quick Start Guide

DANFOSS LX205T TOUCHSCREEN PROGRAMMABLE THERMOSTAT  

CONTENTS

HOME SCREEN

ITEMS

• Day and time
• Current temperature
• Target temperature or setpoint
• Heating indicator – when visible, system is heating
• Next scheduled change
• Access Main Menu
• GFCI Test Button
• On/Off/GFCI Reset Button
• Press to turn system ON
• Hold to turn system OFF
• Press to reset the GFCI

WARNINGS:

• To avoid electric shock, disconnect the heating system power supply at the main panel before installation and maintenance of the thermostat.
• Keep thermostat air vents clean and free from obstruction. This thermostat is an electrical device and must be installed in compliance with national and/or local electrical codes. Installation must be performed by qualified personnel where required by law.
• If a power module with an equipment ground fault protection device (EGFPD) is to be installed where national and/or local electrical codes require a ground fault circuit interrupter (GFCI), a separate GFCI must also be installed.

INSTRUCTION

• Loosen the screw at the bottom and remove the faceplate.
• Do not attempt to remove the screw completely
• Turn the power source OFF at the breaker panel. Make electrical connections to the power base. See Warnings.
• AWG between 12 and 20.
• Note! Do not detach the screws from the terminals.
• When tightening the screws, use a torque of between 0.8 and 1.2 Nm, (0,6 and 0,8 ft.lbs)
• The floor sensor must not come in contact with electrical wires in the wall and must be routed outside the electrical box.
• Thread the floor sensor cable through hole in the power base.
• Push the electrical wires to the back of the electrical box
• Push the power base into the electrical box.
• Secure the power base to the wall
• The Floor sensor has no polarity. Connect it to the terminals C and D.
• The power module connects to the termianals A and B*
• Make the sensor connections.
• Remount the faceplate.
• Tighten the screw at the bottom.
• Perform system and GFCI/EGFPD tests. Once thermostat setup is complete, confirm “Your thermostat will start heating the floor” to complete the startup wizard.

CLASSIFICATION

The product is a Class II device (reinforced insulation) and must be connected to the following leads:

•  Phase L1 (L) 120 V
•  Neutral L2 (N) 0-120 V
•  Max. load 15 A (resistive load)
•  The thermostat is intended to be used with underfloor heating.

TECHNICAL DATA

• Supply Range………………………………………………. 120/240 Vac 50/60 Hz
• Load ……………………………………………………….max. 15 A (resistive load)
• Max. power at e.g. ……………………………………………. 1800 W at 120 Vac
• ………………………………………………………………………. 3120 W at 208 Vac
• ………………………………………………………………………. 3600 W at 240 Vac
• UDG4 (GFCI) …………………………………………….. Class A (5 mA trip level)
• Temperature range ……………………………..+5 to +40°C / +41 to +104°F
• Amb. temp. range …………………………………. 0 to +25°C / +32 to +77°F

CERTIFICATION

• UL Listed for the US and Canada
• According to the following standards:
• Thermostat: UL 60730-1
• UL 60730-2-9
• CSA E60730-1:13
• CSA E60730-2-9
• UL file number: E157297
• UDG4 GFCI: UL 943 4th ed.
• CSA C22.2 No. 144.1-06

Danfoss

• 11655 Crossroads Circle
• Baltimore, MD 21220
• 1.866.676.8062
• © 2015 OJ Electronics. All rights reserved.
• This manual and parts thereof are protected under Danish and international copyright laws

REFERENCE:

DOWNLOAD MANUALS:

DANFOSS LX205T TOUCH SCREEN PROGRAMMABLE THERMOSTAT Quick Start Guide

OTHER MANUALS:

DANFOSS LX205T TOUCH SCREEN PROGRAMMABLE THERMOSTAT Installational Manual

DANFOSS LX205T TOUCH SCREEN PROGRAMMABLE THERMOSTAT Product Specifications Guide

DANFOSS LX205T TOUCH SCREEN PROGRAMMABLE THERMOSTAT Quick Start Guide